John Lewis School House Opal Pendant
Thank you for purchasing this School House opal pendant. Please read theinstructions carefully before use to ensure safe and satisfactory operations of this product. Please keep this instruction for future reference.
Warnings!
For your safety, this product must be installed in accordance with local BuildingRegulations.If in any doubt, or where required by the law, consult a competent person who is registered with an electrical self-certification scheme. Further information is available online or phone your Local Authority.To prevent electric shock, switch off the mains supply before installing ormaintaining this product. Ensure other persons cannot restore the electricity supply without your knowledge.Always use the correct bulb type with the correct wattage as indicated in the specification table. This product is Class I = 
and should be fitted to a lighting Supply (with earth) protected by a 5 amp fuse or equivalent circuit breaker. When changing the bulb, always switch off at the mains and allow the old bulb to cool down before handling. Dispose of used bulbs carefully.
This fitting is rated IP44 making it suitable for use in Zones 1 & 2 of a bathroom when fitted in accordance with IEE wiring regulations (see diagram overleaf). Fitting must be connected to a supply protected by a 30mA RCD in Zone 1.Caution! The bulb and surrounding parts can become hot during use.For indoor use only.
Care instructions
We recommend cleaning with a soft dry cloth. Do not use abrasive materials, as these will damage the finish.Replace bulb from John Lewis or established brand of the same type and compatibility.
Parts list
|
Part List |
Qty | Part List | Qty | Part List |
Qty |
|||
|
A |
 |
1 |
C |
 |
2 |
F |
 |
1 |
|
D |
 |
2 |
||||||
|
B |
 |
1 |
E |
 |
2 |
Assembly
Never install your appliance on a wet, freshly painted or plastered surface. Ensure the house electricity supply is switched off at the fuse box. If removing an existing fitting, note down all wiring connections. Check the fixings will not touch any existing wiring before drilling and attaching the light to the ceiling.Ensure you thread the ceiling wires through the black insulating tube fixed to the appliance.
Step 1Remove mounting plate (B) from fitting by removing the retaining screws and any washers, retain for later. Using the mounting plate as a template, mark and then drill the fixing holes in the ceiling (ensure the screws are firmly fixed into a solid or other suitable mounting and not just the plasterboard.) Take care not to damage wiring. Attach mounting plate to the mounting surface using suitable fixings. Do not attach fitting to mounting plate at this stage. Make sure no wires are trapped in the process.
Step 2Ensuring that the power has been isolated, Lever open the terminal block box cover with a screwdriver, pierce a hole in the black rubber end cap of the terminal block then feed supply cable through.Make electrical connections as follows:
- Connect supply live to fitting live (marked “L”) on the terminal block.
- Connect supply neutral to fitting neutral (marked “N”) on the terminal block.Connect the supply earth to the earth (marked “
”) on the terminal block.
NOTE: Ensure electrical connections are tight and no loose strands of wire are left out of the connector block. Ensure terminals and rubber sleeve are correctly seated then close connector block housing. Excess cable must be carefully located inside ceiling cup or within the ceiling void.Height Adjustment: This fitting is height adjustable at point of installation only. No attempt must be made to adjust the height once it has been attached to the ceiling. If adjustment is required at a later date the fitting must be isolated from the mains and removed from the ceiling first. Lay the fitting on a clear covered surface. Using a suitably sized flat bladed screwdriver loosen the plastic screw clamp under the ceiling cup, also undo the screws or clamp located in the ceiling cup. Carefully pull the cable through the ceiling cup to the desired height and then retighten all screws to ensure that clamps are fully secured. Excess cable must be carefully located inside ceiling cup or within the ceiling void.
Step 3Carefully offer fitting over mounting bracket then secure in place with the screws and washers removed earlier. Fit the bulb, type and wattage as indicated on the fitting (bulb not supplied). The wattage indicated must not be exceeded. To fit the shade: loosen the screws on the lamp holder cap. Place the outer glass shade over the lamp holder. Tighten the securing screws a little at a time so they insert evenly until shade is fully secured. Take care not to cross-thread or over tighten as this may cause damage to the glass or the fitting. Once installation is complete, the electricity may be restored at the fuse box.
Recommended bulb
- 1 x 8 Watt ES energy efficient LED bulb
- Bulb not included
Specification
- Max power: 8W
- Voltage: 220~240V, 50/60Hz
- IP44
- Weight 1.6 Kg
Please retain these instructions for future reference.This symbol 
indicates that this product should not be treated as normal house hold waste and it should be recycled. John Lewis does not operate in store take back, but as members of the Distributer Take Back scheme have funded the development and upgrade of recycling facilities across the UK. Please take it to your nearest collection facility or for further details contact your local council or visit www.recycle more.co.uk.We have taken great care to ensure that this product reaches you in perfect condition. However, should any parts be damaged or missing please e-mail[email protected]
Troubleshooting
Why is the light not working when switched on?Check your power supply is switched onTurn off light and check that the bulb is inserted correctlyCheck the bulb is still in working order.
171 Victoria StreetLondon SW1E 5NNJohnlewis.com
References
[xyz-ips snippet=”download-snippet”]