JVC Marine Speaker Instruction Manual
Parts
IMPORTANT SAFETY INSTRUCTIONS
Caution: Read this page carefully to ensure safe operation.
WARNING
- Before mounting or wiring etc., be sure to remove the wire from the battery ground
- When extending the power supply wire (+12 V) or ground wire, make sure to use
- To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the speaker.
- If the product emits smoke or an unusual odor, turn off the power supply immediately the (set it to the standby mode) and stop using it. After this, please contact your dealer or nearest service station as soon as possible.
- This product is for 12 V power supply only.
- After taking the product out of the polyethylene bag, be sure to dispose of the poly-ethylene bag out of the reach of children. Otherwise, they may play with the bag, which could cause hazard of suffocation
Do not ingest the battery, Chemical Burn Hazard.The remote control supplied with this product contains a coin/button cell battery.
- If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children.
- If the battery compartment does not close securely, stop using the product and keep it away from children.
- If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
CAUTION
- Installation and wiring of the product requires expert skill and experience. To ensure safety, be sure to have your dealer or specialist perform the installation and wiring.
- Do not install the product in a spot exposed to excessive heat or humidity.
- Do not install the product in unstable locations or locations subject to dust.
- Do not use gasoline, naphtha, or any type of solvent to clean the product. Clean by wiping with a soft, dry cloth.
- Connect the speaker wires to appropriate speaker connectors separately. Sharing the negative wire of the speaker or grounding speaker wires to the metal body of the boat/vehicle can cause this product to fail.
- When making a hole under a seat, inside the trunk, or somewhere else in the boat/ vehicle, check that there is nothing hazardous on the opposite side such as a gasoline tank, brake pipe; or wiring harness, and be careful not to cause scratches or other damage.
- Do not secure the ground wire to the bolts or nuts of important safety equipment such as: Steering or braking devices, airbag mechanisms (Can cause accidents.)
- Fasten the product securely so that it does not get detached due to sudden deceleration and becomes a hindrance to driving to ensure that it does not pose a danger to the passengers. (Cause of injury or accidents.)
- After installing the product, check that the following electrical equipment are working properly.- Lights, navigation lights, brake lights, turn signal lights, windshield wipers, horn device, etc.
- The helmsman or driver must always stop the boat or vehicle in a safe location before performing the next action.- Remote control operation
- Do not use the product for purposes other than on-board mounting.
- Keep the volume of sound at an optimum level. Not being able to hear sounds from outside of your car can lead to traffic accidents.
- To prevent damaging the speaker, turn off the power of amplifier before connecting it to the speaker.
Connections
WARNING
Remove the ignition key and disconnect the negative
terminal of the battery to prevent short circuits.
CAUTION
Check that no unconnected wires or connectors are touching the metal parts or car body.
Wiring
- In a computer-equipped boat/vehicle, when you remove the
terminal of the battery, the memory may disappear, or a defect may occur in the electrical system of the boat/vehicle. Consult your dealer for further details. - Do not allow the wire to directly contact the edge of the iron plate by using grommets.
- Do not turn the power on if the ground wire is not connected. Connect the ground wire to a metal part of the car chassis that acts as an electrical ground passing electricity to the battery`s negative terminal.
Connecting the speaker cords
With this product, the speaker cords are not supplied. Obtain the audio speaker cords with the required length. To connect the speaker cords to the speaker, terminate the wires with female spade connectors.12 – 22 AWG speaker cord is recommended.
Connecting the power supply wires and link cable (RGB LED)
- Pass 2 heat shrink tubes (6) onto the link cable B(5) .
- Connect the link cable B (5) to the left and right speakers.
- Put the heat shrink tube (6)over the connection area of the connector. Apply heat with a heat gun or similar to shrink the tube and protect the connector from moisture, etc. (Refer to Fig. 3) Protect the 2 connectors that are not in use with heat shrink tubes(6). (Refer to Fig. 4)
- Connect the ground wire (black) and the +12 V wire (yellow) of the controller of speaker A (1)
- Reconnect the negative terminal of the battery. Do not use link cable A (4)for this connection.
Do not connect the +12 V wire and ground wire in reverse. Incorrect connections can cause failure.
When connecting the power supply (+12 V) directly to the battery
CAUTIONBe sure to connect a 3 A fuse between the power cord (+12 V) of the controller of speaker A(1) battery. The cord length between the battery and the fuse must not exceed 90 mm (3-9/16″).
Do not connect the +12 V wire and ground wire in reverse. Incorrect connections can cause failure.
When using multiple pairs of speakersA maximum of up to 6 pairs of speakers can be connected. Connect the link cables of the second and subsequent pairs of speakers as shown on the right. The figure shows an example of connecting 3 pairs of speakers. Connect the fourth and subsequent pairs speakers in the same way as the third pair. Protect the 2 connectors that are not in use with heat shrink tubes . (Refer to Fig. 4)You can control all the LED lights with one remote controller, but you cannot control just a specific speaker.
Do not let the wire come out from the tab.
Installation
Speaker locations
How to use the template
Controls
CAUTIONDo not leave or install the remote control in hot places such as on the dashboard.
(1) 
(Turn on/Standby)Press to switch the LED lights of the speakers ON/OFF (standby mode).Last memory functionWhen the product is turned on, it will operate in its previous status.
(2) SPEED – (3) SPEED +Dynamic speed adjust Adjust dynamic playing speed. Press SPEED+ to increase speed and press SPEED – to decrease speed.Adjust speed : 7 steps
(4) COLOR + (5)COLOR –Static color adjustSwitch to static color mode from dynamic mode, or switch between different static colors.Select color : 21 colors
(6)MODE +(7) MODE –Dynamic modes adjustSwitch to dynamic mode from static color mode, or switch between dynamic modes.Select mode : 21 modes
(8) BRIGHT + (9) BRIGHT –Brightness adjustAdjust static color brightness. Press BRIGHT+ to increase brightness and press BRIGHT – to decrease.Adjust brightness : 8 steps
(10)DEMOSwitching to the demo mode Press the MODE (+/-) key to exit the demo mode.
(11) Signal transmission indicatorThe LED lights up in red when a key is pressed and a signal is transmitted.
How to replace the batteryIf the Remote Controller operates only over shorter distances or does not operate at all, it is possible that the battery is depleted. In such instances, replace the battery with new one.
CAUTION
- Risk of fire or explosion if the battery is replaced by an incorrect type. Use a button battery CR2025 (use only the approved battery).
- Risk of fire, explosion or the leakage of flammable liquid or gas if the battery is left in an extremely high temperature surrounding environment and/or subjected extremely low air pressure. The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
- Risk of fire, explosion or the leakage of flammable liquid or gas if the battery is disposed into fire or a hot oven, recharged, shorted, mechanically crushed or cut of the battery.
- If spilled fluid comes in contact with your eyes or on clothing, immediately rinse with water and consult a physician.
Specifications
Design and specifications are subject to change without notice.SpeakersWoofer…………………………………………………………16 cm (6-1/2 in.) PP Mica coneTweeter……………………………………… 1.3 cm (1/2 in.) PEI Balanced domePeak power…………………………………………………………………………………………….260 W75 Watts RMS Impedance ……………………………………………………………………………………………..4Ω
Sensitivity……………………………………………………………………….86 dB / W at 1 mFrequency response ………………………………………………65 Hz ~ 21,000 HzCutout diameter…………………………………..5-11/16 in. (14.48 cm) CircleMounting depth ………………………………………………….. 2-9/16 in. (6.49 cm)[Control unit]Operating voltage………………………….12 V DC boat battery/car batteryMaximum current consumption………………………………………0.5 A (1 pair)Remote distance (open area)………………………………………………30 m (98 ft.)IPX5 Water resistant
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed nictations. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:— Reorient or relocate the receiving antenna.— Increase the separation between the equipment and receiver.— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Troubleshooting
Often, what appears to be a malfunction is due to user error. Before calling for service, please consult the following table.
Supplier’s Declaration of Conformity
Trade Name: JVCProducts: SPEAKERModel Name: CS-DR621MWL / CS-DR620MBLResponsible Party: JVCKENWOOD USA CORPORATION 2201 East Dominguez Street, Long Beach, CA 90810, U.S.A. PHONE: 310 639-9000
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
CALIFORNIA, USA ONLYThis product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material– special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate
References
[xyz-ips snippet=”download-snippet”]