KAISER BAAS KBA13113 S1 Single Axis Gimbal User Manual

KAISER BAAS KBA13113 S1 Single Axis Gimbal User Manual

SAFETY PRECAUTIONS

Before using your Kaiser Baas SI Gimbal Please ensure you read and understand the following product and safety precautions.

• Dropping or otherwise impacting the gamble may damage the product causing a to malfunction.
• Ensure there is nothing obstructing the Gimbal wren the SI Is powering on.
• The Si Gimbal is not water resistant. Do not use any liquid cleansers. Only use a soft dry cloth to clean the SI.
• Keep the Si away from sand and dust to safeguard the sensors In the motors.
• ONLY recharge the SI using the supplied USB cable: If using a wall charger, ensure that it is a certified product for your region. AC Input: i CO-240VAC 50/60Hz. CC Output. 5V Only use a USB wall charger with suitable approval and certification. Do not charge in conchtions outside of the 10°C – 45C range. If you do not know the voltage and current of your charger. use the Included cable to charge from you’ computer.
• The Gimbal should not be used in heal exceeding 55C (131`e).
• DO NOT drop. crush. pierce. bend. delorm, microwave. incinerate or damage the Gimbal.

IMPORTANT BATTERY SAFETY INFORMATION

• DO NOT use any third-party or unknown accessories or batteries.
• DO NOT disassemble the battery.
• DO NOT short-circuit the battery. Short circuiting may occur when the battery touches other motel objects.
• DO NOT charge the battery n direct sunlight.
• Always charge the battery in a designated space. away from people and animals.
• DO NOT leave a battery on prolonged charge when not in use.
• It the battery has a Non surface temperature, leave d to cool before no try to re-cterge it.
• DO NOT charge the battery it the ambient temperature is below 10’C or above 45^C.
• Always use the supplied charger and observe manufacturer charging requirements.
• Battery performance is best when within normal room temperature (5t-20t1).
• Batteries need to be charged before use.

PRODUCT DIAGRAM

PRODUCT DIAGRAM

1. Micro USB charging port
2. Positioning bead
3.  Phone clip
4. Gimbal status indicator
5. Gimbal power button
6. Rotation lock
7. Extend pole
8. Capture/record button
9. Bluetooth remote indicator
10. Tripod grip

CHARGING YOUR S1 GIMBAL

Charge your gimbal using the Micro USB cable supplied. Once the Si has finished charging the red LED indicator will turn off and the green LED indicator light will turn on.

CHARGING THE BATTERY IN YOUR REMOTE CONTROL

if you find it challenging opening the remote simply slot a strong slim object into the side slot on the remote and carefully twist.

TO TURN ON/OFF THE GIMBAL

To power ON / OFF the Gimbal, press and hold the power button 5 for few seconds.

TO TURN ON/OFF THE REMOTE CONTROL

To power ON / OFF the Remote Control, press and hold the power button 8 for few seconds.

SETTING UP YOUR REMOTE CONTROL

Pull out the battery insulter from the remote control.

CONNECTING THE REMOTE CONTROL TO YOUR PHONE

1. Turn on the remote control by pushing the power button for 3 seconds until the blue LED light flashes.
2. Turn on Bluetooth via Settings on your smartphone. Search and connect to KB-BT.

SETTING UP YOUR Si GIMBAL

1. Unfold the gimbal and tighten the rotation lock.
2. Open the Phone Clip and place your smartphone in the holder. Move and adjust the positioning until the phone is centered and balanced.Note; If the gamble is not well-balanced and turned on it could cause overheating or excessive power consumption.

USING GIMBAL MODE

The S1 one can be used with or without Gimbal mode turned on. To turn on gimbal mode rotate the gimbal unit clockwise so it isn’t clipped to the Positioning Bead. Press the Gimbal Power Button 5 for 3 seconds to turn on the gimbal function.

Take photos or videos using either your camera or the remote control if you have connected it.

SWITCHING BETWEEN PORTRAIT AND LANDSCAPE MODE

To switch between portrait or landscape simply click the Gimbal Power Button 5 and it will switch between vertical mode and landscape mode.

USING YOUR Si AS A SELFIE STICK

When the gimbal function is turned off turn the body of the gimbal around until it locks into the positioning bead and it can then be used as a selfie stick.

USING THE TRIPOD

Open the three tripod legs and place it on a horizontal table. Adjust the overall center of gravity depending on phone positioning to avoid tilting.

SPECIFICATION

Payload:300gNet Weight:230gBattery CapacityLio-ion 400mAhCharging Port:Micro USBCharging Voltage:5VOperating Current:50mA – 900mAOperating Time:2 – 3 HoursCharging Time: 2 HoursBluetooth Remote Range:10mBluetooth Remote Battery Type:CR1620Product Size:19010’40mmExtended Length:592mm

SUPPORT

Having trouble with your Gimbal?Don’t worry. our friendly support team can help. Please visit us at: www.kaiserbaas.com/supporl Or send us an email at: helpdeskRkaiserbaas.com

FAO

Q: My remote control isn’t working?A: The remote control MI go into sleep mode alter 10 minutes of no operatic” Simply clip the remote control capture button to wake it up. II this doesn’t work your battery may need replacing.Q: The remote control is showing a red LED.A: When the remote control battery ex low the red LED light turns on.