OA8500 Low Profile Digital HDTV Over The Air Antenna
TMOwner’s Manual
OA8500 · White OA8501 · Black
and and
………………………………………………… …………………………………………..………………………………………………. 3 …………………………………………………. 4 ………………………………………………………… …………………………………………………………………………….. 6
Please read thru the installation instructions before beginning. See page 2 for items supplied by the installer. See page 5 for information on the MB8200 Mounting Plate
Dimensions:
8.7″ H x 16″ W x 12.5″ L
Weight:
2.62 lbs.
Power Requirement: 12 VDC / 100 mA (supplied by KING Wall Mount Power Injector)
Frequency Bands:
VHF (54-216 MHz) UHF (470-698 MHz) FM (87.9-107.9 MHz)
Signal Meter Frequency Response: 54-698 MHz (Ch 2-51)
Enclosure/Mount: ASA-Automotive grade
1. Turn on TV and power injector (see above).2. Turn on KING SureLock Signal Meter with switch on side of enclosure.3. Press button and turn knob to rotate antenna in one direction until it hits the stop.4. Rotate attenuator dial fully clockwise.
5. Slowly rotate antenna a full 360 degrees. Antenna will hit stop again.As you rotate it, note where the maximum number of LEDs illuminate on signal meter.If the same number of LEDs stay lit through the whole rotation, turn the attenuator down slightly and rotate the antenna again.Rotate the antenna back to where the most LEDs illuminated and center it in that area.6. Rotate attenuator dial counter clockwise
Arrow on knob indicates which direction antenna is pointing.LEDs will illuminate from left (next to power) to right.All LEDs may not illuminate depending on signal strength.
8. Repeat steps 6 and 7 to pinpoint signal reception. 9. Follow instructions in TV or converter box owner’s manual to scan for available channels. Watch TV!Page 1
· Remove the existing adjustable connector from the upper connector located in the base mount.as shown at right and engage the extension onto the upper connector. · Leave extension sticking out of base mount more than the thickness of the roof.Page 2
1. Select an area on the roof for the base mount keeping in mind the following
:
2. Drill a 2-1/4″ hole
all the way thru the vehicle roof where the adjustable connector will go.
3. Carefully pull out the adjustable connector so it will extend beyond the thickness of the roof when the base mount is installed. It must extend thru the roof to allow installation of interior components. Exact length will be adjusted when interior components are installed.
4. Connect the coax from the power inserter’s antenna input to the open connection on the splitter in the base mount.
adjustable connector and interior coax going thru the roof hole and into the interior of the vehicle.6. Hold the base mount in position and rotate the antenna by hand. without interference from sealant, coax, roof insulation, etc. Fasten the base mount to the roof. Make sure the basemount is sealed all the way around. Make sure the coax channel and fastener heads are sealed as well.
Page 3
1. Press knob button and remove knob from enclosure base. 2. Route the coax thru the coax hole in the enclosure base. Place theenclosure base around the adjustable connector and against ceiling. (The enclosure base will seat around the centering ring on the adjustable connector.) Fasten the enclosure to the ceiling with four included screws. 3. Press the knob button and push knob onto the end of the adjustable connector. enclosure. Fasten knob to connector with screw. 4. Route the coax around the raised ring as shown and connect the coax to the RF connector on the KING SureLock signal meter. 5. Optional: If desired, apply the decal to the enclosure cover. 6. Carefully align the cover and snap into place. Make sure not to damage or bend LEDs or pinch the coax cable.Page 4
· Can be mounted in most standard electrical boxes. · Requires a +12 Volt DC power source. (Inadequate voltage may cause the green LED to not illuminate and the unit tonot function properly. · Requires .25″ female spade connectors for power and ground connections. · Has an internal fuse rated @ 400 mA max. If tripped, the fuse will reset when the circuit cools.Page 5
Every new KING Jack HDTV Antenna System is thoroughly inspected and tested before leaving the factory, and is covered by the following limited warranty from the date of original purchase:· Four-year parts warranty: The customer is not responsible for the cost of replacement parts if the original part is determined to be defective under the terms of the warranty. The customer is responsible for the cost of replacement parts after four years.· One-year labor warranty: The customer is not responsible for labor costs to repair unit if unit falls under the terms of the warranty. Any warranty labor outside of that performed at the factory is not covered unless the product has been installed by an authorized dealer/installer or OEM manufacturer. The customer is responsible for all labor costs after one year.Should any trouble develop during the warranty period, contact KING. You must contact KING before the warranty period expires. The customer must supply proof of purchase (such as a dated sales receipt) when requesting warranty service. If customer cannot supply proof of purchase, warranty period shall start 30 days after date of manufacture.KING may authorize the dealer to perform the necessary repairs, or may have the unit returned to KING for repairs.dealer on how to proceed with any repairs.If it is determined that the unit needs to be returned to KING, customer must return COMPLETE product, freight prepaid, to: .If inspection shows the trouble is caused by defective workmanship or material, KING will repair (or at its option, replace) without charge.When returning product, KING will supply an RMA number (Return Merchandise Authorization). This number must be clearly written on the box. Failure to clearly write RMA number on box may result in delays in processing claim. Along with product, customer should include in the box: his/her name, address, daytime phone number, proof of purchase and description of the problem.This warranty does not cover installation and external wiring, or remanufactured units. This warranty is not transferable from the original owner.This warranty also does not apply where: · The product has been abused, misused, improperly installed or improperly maintained. · The product has been used with an accessory other than a KING accessory designed for the product. · Repairs are required because of normal wear and tear. · Alterations have been made to the product. · The product or any associated component has been opened without authorization or disassembled to any degree. · Damage has been caused by power washing. · Circumstances beyond the control of KING cause the product to no longer operate correctly. · Customer is not the original owner.do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.Page 6
Simply better, by design.TM11200 Hampshire Avenue South, Bloomington, MN 55438 PH 952.922.6889 || FAX 952.922.8424 || kingconnect.com© 2018 KING 22600 Rev B
References
[xyz-ips snippet=”download-snippet”]