KitchenAid KCES950HSS 30 Inch Electric Cooktop with 5 Elements and Touch-Activated Controls User Guide

Table of Contents

Get the App and Get ConnectedWith your mobile device, get the app, connectivity setup instructions, terms of use, and privacy policy at: www.kitchenaid.com/connect

In Canada, visitwww.kitchenaid.ca/en_CAand click on the KitchenAid®Connected Appliances link.IMPORTANT: Proper installation of your appliance prior to use is your responsibility. Be sure to read and follow the Installation Instructions that came with your appliance.Connectivity requires Wi-Fi and account creation. App features and functionality are subject to change. Data rates may apply. If you have any problems or questions, call KitchenAid® Connected Appliances at 1-877-559-2603.

You Will Need:

■A home wireless router supporting Wi-Fi, 2.4Ghz with WPA2 security. If you are unsure of your router’s capabilities, refer to the router manufacturer’s instructions.■The router is to be on and have a live internet connection.■The 10-character SAID code for your appliance. The SAID code is either printed on a label on the appliance or can be foundon the LCD screen. Refer to the appliance User Guide for the location.

Once installed, launch the app. You will be guided through the steps to set up a user account and to connect your appliance. If you have any problems or questions, call KitchenAid®Connected Appliances at 1-877-559-2603.

Connected Appliance Regulatory Notices Federal Communications Commission (FCC) Compliance Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one ofthe following measures:─Reorient or relocate the receiving antenna.─Increase the separation between the equipment and receiver.─Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.─Consult the dealer or an experienced radio/TV technician for helpThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

RF Exposure Information

To comply with FCC/IC RF exposure requirements for mobile transmitting devices, this transmitter should only be used or installed at locations where there is at least a 20 cm separation distance between the antenna and all persons.To comply with FCC/IC RF exposure limits for general population/uncontrolled exposure, the antenna(s) used for thisthe transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Industry Canada (IC) Compliance Notice

This device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions:1. This device may not cause interference,2. This device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.)is not more than that necessary for successful communication.The radio transmitters IC: 10248A-WICHAM01 and10248A-FLDAAM01 have been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Antenna Type	Maximum PermissibleAntenna Gain (dBi)	Required Impedance(OHM)
Slot	1.2	50
Monopole(WICHAMO1 only)	0.5	50
Dipole	3.0	50
F	1.60	50
Planar F	4.2	50

To comply with FCC and Industry Canada RF radiation exposure limits for the general population, the antenna(s) used for this transmitter must be installed such that a minimum separation distance of 20 cm is maintained between the radiator (antenna) and all persons at all times and must not be co-located or operating in conjunction with any other antenna or transmitter.

OEM Responsibilities to comply with FCC and Industry Canada Regulations

The WICHAM01 / FLDAAM01 Modules have been certified for integration into products only by OEM integrators under the following conditions:1. The antenna(s) must be installed such that a minimum separation distance of 20 cm is maintained between the radiator (antenna) and all persons at all times.2. The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter. As long as the two conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).Module made by Whirlpool Corp.

IMPORTANT NOTE: In the event that these conditions cannot be met (for certain configurations or co-location with another transmitter), then the FCC and Industry Canada authorizations are no longer considered valid and the FCC ID and IC Certification Number cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC and Industry Canada authorization.

End Product Labeling

The WICHAM01 / FLDAAM01 Modules are labeled with FCC ID and IC Certification Number. If the FCC ID and IC Certification Number are not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case,the final end product must be labeled in a visible area or display the following:“Contains FCC ID: A5UWICHAM01”“Contains IC: 10248A-WICHAM01”or“Contains FCC ID: A5UFLDAAM01”“Contains IC: 10248A-FLDAAM01”The OEM of the WICHAM01 / FLDAAM01 Module must only use the approved antenna(s), which have been certified with this module. The OEM integrator has to be aware not to provide information to the end-user regarding how to install or remove this RF module or change RF-related parameters in the user manual of the end product.

The user manual for the end product must include the following information in a prominent location:

“To comply with FCC and Industry Canada RF radiation exposure limits for the general population, the antenna(s) used for this transmitter must be installed such that a minimum separation distance of 20 cm is maintained between the radiator (antenna) and all persons at all times and must not be co-located or operating in conjunction with anyother antenna or transmitter.”

report this ad

References

[xyz-ips snippet=”download-snippet”]

Posted

2023-01-30

KitchenAid

admin

Tags:

30 Inch Electric Cooktop with 5 Elements and Touch-Activated Controls, KCES950HSS, KitchenAid