KITMA Electric Steam Table Owner’s Manual

KITMA Electric Steam Table

FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

WARNING: Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. Read the Installation, Operating and Maintenance Instructions thoroughly before installing or servicing this equipment.

WARNING: In Europe, appliance must be connected by an earthing cable to all other units in the complete installation and thence to an independent earth connection in compliance with EN 60335-1 and/or local codes.

WARNING: An earthing cable must connect the appliance to all other units in the complete installation and from there to an independent earth connection.

OWNER’S INFORMATION

General Information:

1. Always clean equipment thoroughly before first use.
2. Check rating label for your model designation and electrical rating.
3. For best results, use stainless steel counter tops.

General Operation Instructions:

1. All food‐service equipment should be operated by trained personnel.
2. Do not allow your customers to come in contact with any surface labeled “CAUTION HOT”.
3. Never pour cold water into dry heated units.
4. Do not cook, or hold food directly in wells. Always use steam table pans or inserts.
5. Never hold food below 150°F

SAFETY INFORMATION

Kitma equipment is designed, built, and sold for commercial use and should be operated by trained personnel only. Clearly post all CAUTIONS, WARNINGS and OPERATING INSTRUCTIONS near each unit to insure proper operation and to reduce the chance of personal injury and/or equipment damage. This product is used for the cooking, defrosting or re-thermalization of food products only.

Always disconnect power before servicing the unit.Surfaces will remain hot after power has been turned off.Allow unit to cool before cleaning or servicing.Never clean the unit by immersing it in water.The unit is not protected against water jets;DO NOT CLEAN THE STEAM TABLE WITH A WATER JET.Always clean equipment properly before first use.

Safety Signs and Messages

The following Safety signs and messages are placed in this manual to provide instructions and identify specific areas where potential hazards exist and special precautions should be taken. Know and understand the meaning of these instructions, signs, and messages. Damage to the equipment, death or serious injury to you or other persons may result if these messages are not followed.

This message indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.This message indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.This message indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices.This message is used when special information, instructions or identification are required relating to procedures, equipment, tools, capacities and other special data.

ELECTRICAL SPECIFICATIONS

MODEL	VOLTS	Wells	WATTS/Well	Total WATTS	PH
KSTEA-2	120V	2	500	1000	1
KSTEA-3	120V	3	500	1500	1
KSTEA-4	120V	4	500	2000	1
KSTEA-5	120V	5	500	2500	1
KSTEB-2	240V	2	750	1500	1
KSTEB-3	240V	3	750	2250	1
KSTEB-4	240V	4	750	3000	1
KSTEB-5	240V	5	750	3750	1

The Data plate is located on the front panel.

Power Cord:Six (6) foot, 3 wire grounded cord. If the supply cord is damaged, the manufacturer, or an authorized service agent, must replace it in order to avoid a hazard and warranty. Please contact the factory by calling the 800 # located on the unit

DIMENSIONS

MODEL	Length	Width	Height	Top opening	Cube ft. Crated	Weight
in	mm	in	mm	in	mm	Lbs.	kg
KSTEA-2	30	762	291/2	748	331/2	851	2	10.59	63.9	29
KSTEA-3	441/8	1120	291/2	748	33 1/2	851	3	14.5	83.7	38
KSTEA-4	58	1479	291/2	748	331/2	851	4	18.7	108.7	49.3
KSTEA-5	72 1/2	1836	291/2	748	33 1/2	851	5	28.6	130.5	59.2
KSTEB-2	30	762	291/2	748	331/2	851	2	10.59	63.9	29
KSTEB-3	44 1/8	1120	291/2	748	331/2	851	3	14.5	83.7	38
KSTEB-4	58	1479	291/2	748	331/2	851	4	18.7	108.7	49.3
KSTEB-5	721/2	1836	291/2	748	331/2	851	5	28.6	130.5	59.2

INSTALLATION INSTRUCTION

If the carton appears damaged, or damage is discovered once the carton is opened, stop immediately and contact the freight company to file a damage claim.

CAUTION: The Steam Table is shipped without the legs, under shelf or cutting board shelf attached. Please read the installation and operation instruction before operating the unit. Remove all supports and packaging materials before operating the unit. Failure to remove all packaging materials may lead to a fire and / or damage to the appliance.

1. Remove all external packaging that is protecting top portion of unit
2. Remove all internal packaging to the unit, if present.
3. Visually inspect all external and internal portions of unit for damage.
4. Wipe down the exterior of the unit using a damp cloth with warm water. Do not use abrasive pads or cleaners as they will damage the stainless steel surface.Note: Ambient Conditions – Make sure that the operating location is in an area where the ambient temperature is held constant (minimum 70°F). Please avoid areas such as near exhaust fans and air conditioning ducts.Warning! Operating environmentEnsure that operation location is at a reasonable distance from combustible walls and materials otherwise combustion or discoloration could occur.Caution! Operating environmentPlace unit on a stable, level floor. The unit must be level, both front and back and left to right, in order to maintain an equal water depth throughout the wells. To eliminate rocking or adjust height turn the adjustable feet in the proper direction until the desired results are obtained.Note: Maximum adjustment is 1 inch
5. Before plugging unit into wall outlet or permanently electrical connecting, the unit should be adjusted to the desired height and align with other equipment.
6. The voltage and wattage ratings of this steam table are given on the device nameplate. Connect the steam table to a circuit having a voltage and type of current similar to that stamped on the device nameplate. For movable equipment a proper cord and plug are included for connection to the matching power supply outlet.
7. Plug unit into grounded electrical outlet with correct voltage, and plug configuration.a. Warning! Using any receptacle that is not designed to match the attached cord and plug MAY cause personal injury and WILL void your warranty. Please attach the Steam Table, to an individual branch circuit
8. For permanent installations, connections to supply line may be made through conduit or armored cable. Use copper wire for power supply or suitable copper to aluminum wire connector.
9. The body of the appliance should be grounded by connecting the ground stud provided in the junction box to a good electrical ground.
10. The steam table is not fused and consequently must be connected to a fused circuit equipped with suitable disconnect means, as required by local code authorities.
11. To assembly the units follow steps 1 thru 6 listed below.

NOTICE

UNIT IS SHIPPED UNASSEMBLED. TO MEET NATIONAL SANITATION FOUNDATION STANDARDS, THE INSTALLER MUST USE A NSF APPROVED SILICONE SEALANT TO SEAL THE SEAMS BETWEEN THE UNIT AND ASSEMBLED PARTS.

Step 1Place the unit on the floor upside down. Be sure to protect the top surface and well from damage when the unit is placed on its top on the floor. Once the leg inserts are in place, tighten the set screws in the unit.

Step 2Slide the legs inside the shelf, and tighten it to the unit by the fixed leg inserts

Step 3Locate the shelf at minimum 6 inches from the floor to allow for cleaning and to comply with NSF standards. Tighten the 4 set screws located in each corner of the shelf leg inserts.

Step 4Install the supporting board on the fixing brackets first, then positioning this part in the front of the shell by screws.

Step 5Install the cutting board stops through the shelf and the shelf support brackets at each end as shown.

OPERATION INSTRUCTION

1. PREHEAT – To preheat individual sections, turn the switch dial to high for 10 – 20 minutes before the foods are placed in the compartments. Insure that pan openings are covered to prevent loss of heat.
2. If only part of the food warmers is needed, the compartment not in use does not need to be heated.
3. SWITCH SETTINGSa. The most satisfactory switch settings must be determined by experience based on the nature of the foodservice and the type of operation as well as individual preference of the restaurant operator. The proper switch setting necessary to keep foods at the desired temperature will vary dependent upon the frequency of turnover, size of food containers, amount of food in each container, room temperature, location of food warmer with respect to range or other heated equipment, air outlets, fans, doors and passageways.

CLEANING

Insure the appliance has been turned off and has had sufficient time for all surfaces to cool down before cleaning.

DAILY CLEANING

1. Turn the control knob to the OFF position and allow unit to cool before cleaning.
2. Clean or remove water from the well.CAUTION: Do not allow water to splash or run on to the controls or wiring.
3. Use a soft cloth or sponge with a mild detergent to clean the entire warmer assembly.Rinse completely with warm water and then dry.
4. A plastic scouring pad and a mild detergent may be used to remove hardened food.NOTICE: Do not use steel wool.

WEEKLY CLEANING

1. Scale deposits due to the mineral content of the water may be removed using a plastic scouring pad and a de-scaling agent approved for use on stainless steel. It is important to keep these deposits from building up as they may cause corrosion of the stainless steel well.
2. After de-scaling, the well assembly should be rinsed thoroughly with a solution of vinegar and water to neutralize all cleaner residues.
3. Wipe the well assembly dry and leave uncovered.

WARNINGDo not use any highly caustic cleaners, acids or ammonia. These may cause corrosion and/or damage to the stainless steel well. Do not allow water to stand in the well.Water must be removed from the well and the well cleaned after each use.

CLEANING PROCEDURES FOR THE CUTTING BOARDS

When high pressure cleaning equipment is not available; use hot water, a granular cleanser or detergent and a stiff bristle brush. (Abrasive action is necessary, as simply wiping the board will not suffice.) After Scrubbing, rinse thoroughly with hot water. Allow to lie flat.

Several excellent germicidal cleaners are also available, including Calgon’s “Big Cat” and Johnson’s “Break Up”. Clorox is another good cleaner and is USDA approved.

The tabletop material is cut into sections not larger than 36″ in any plane, and no section weighs more than fifty (50) pounds. These are stipulations of the National Sanitation Foundation to facilitate cleaning. The tops should be turned over daily to reduce possibility of warping and should never be stood on end. Periodically, go over the board with a clean, flat stainless steel scraper to help seal some of the knife marks.

The use of cleavers on synthetic boards or tabletops is not recommended.

TROUBLESHOOTING

Always ask and check the following:

TROUBLE SHOOTING GUIDE

1. Problem: Unit does not heat:a. Has unit been connected to a proper electrical source of the proper voltage?b. Is electric turned on at the main? Check the circuit breaker or fuse.c. Are the control knobs set to the “ON” position?
2. Problem: Unit does not maintain proper food temperature.a. Are the controls set to the proper setting?b. Has unit been pre-heated appropriately?c. Were pans of food placed into unit at or above desired temperature?d. Has the food been kept covered?e. Are there air conditioning ducts, take-up air ducts or fans located near or over unit, causing cool drafts?f. Has unit been connected to a proper electrical source of the proper voltage? If so, is there a “low” voltage condition?

PREVENTATIVE MAINTENANCE SCHEDULE

Please follow the cleaning section for the daily and weekly preventative maintenance schedule.

1. Use the proper tools.When cleaning stainless steel products, use non-abrasive tools. Soft cloths and plastic scouring pads will not harm steel’s passive layer. Stainless steel pads also can be used but the scrubbing motion must be in the direction of the manufacturers’ polishing marks.
2. Clean with the polish linesSome stainless steel comes with visible polishing lines or “grain.” When visible lines are present, always scrub in a motion parallel to the lines. When the grain cannot be seen, play it safe and use a soft cloth or plastic scouring pad.
3. Use alkaline, alkaline chlorinated or non-chloride containing cleaners.While many traditional cleaners are loaded with chlorides, the industry is providing an ever-increasing choice of non-chloride cleaners. If you are not sure of chloride content in the cleaner used, contact your cleaner supplier. If your present cleaner contains chlorides, ask your supplier if they have an alternative. Avoid cleaners containing quaternary salts; it also can attack stainless steel and cause pitting and rusting.
4. Keep your food equipment clean.Use alkaline, alkaline chlorinated or non-chloride cleaners at recommended strength. Clean frequently to avoid build-up of hard, stubborn stains. If you boil water in stainless steel equipment, remember the single most likely cause of damage is chlorides in the water.Heating cleaners that contain chlorides have a similar effect.
5. Rinse.If chlorinated cleaners are used, wipe equipment and supplies dry immediately.The sooner you wipe off standing water, especially when it contains cleaning agents, the better. After wiping equipment down, allow it to air dry; oxygen helps maintain the stainless steels passivity film.
6. Never use hydrochloric acid (muriatic acid) on stainless steel.
7. Regularly restore/passivate stainless steel.

KSTEA-2/KSTEB-2 Wiring Diagram

KSTEA-3/KSTEB-3 Wiring Diagram

KSTEA-4/KSTEB-4 Wiring Diagram

KSTEA-5/KSTEB-5 Wiring Diagram

Parts List and Exploded View

PARTS LIST

Item#	Description	KSTEA-2	KSTEA-3	KSTEA-4	KSTEA-5
1	Heating element-120V:500W	KSTEA-2-001
2	Body-SUS	KSTEA-2-002	KSTEA-3-002	KSTEA-4-002	KSTEA-5-002
3	Thermostat-120V:13A	KSTEA-2-003
4	Control panel-PET	KSTEA-2-004
5	Power light-120V 56K LED	KSTEA-2-005
6	knob guard-Q235 Chromed	KSTEA-2-006
7	Knob-PA	KSTEA-2-007
8	Heating light-120V 56K LED	KSTEA-2-008
9	Cutting board-PE	KSTEA-2-009	KSTEA-3-009	KSTEA-4-009	KSTEA-5-009
10	Position shaft-SUS	KSTEA-2-010
11	Supporting board-SUS	KSTEA-2-011	KSTEA-3-011	KSTEA-4-011	KSTEA-5-011
12	Fixing bracket-SUS	KSTEA-2-012
13	Power cord	KSTEA-2-014	KSTEA-4-014
14	Adjustable feet-SUS	KSTEA-2-013
15	Round lube-SUS	KSTEA-2-015

PARTS LIST

Item#	Description	KSTEB-2	KSTEB-3	KSTEB-4	KSTEB-5
1	Heating elemenl-208-240V:750W	KSTEB-3-001
2	Body-SUS	KSTEA-2-002	KSTEA-3-002	KSTEA-4-002	KSTEA-5-002
3	Thermostat-208-240V:13A	KSTEB-3-003
4	Control panel-PET	KSTEA-2-004
5	Power light-250V 156K LED	KSTEB-3-005
6	knob guard-Q235 Chromed	KSTEA-2-006
7	Knob-PA	KSTEA-2-007
8	Heating light-250V 156K LED	KSTEB-3-008
9	Cutting board-PE	KSTEA-2-009	KSTEA-3-009	KSTEA-4-009	KSTEA-5-009
10	Position shaft-SUS	KSTEA-2-010
11	Supporting board-SUS	KSTEA-2-011	KSTEA-3-011	KSTEA-4-011	KSTEA-5-011
12	Fixing bracket-SUS	KSTEA-2-012
13	Power cord	KSTEB-3-014
14	Adjustable feet-SUS	KSTEA-2-013
15	Round lube-SUS	KSTEA-2-015