USER GUIDE
PORTABLE TV MOUNT STAND CART
(32″ – 55″)KASTTVPB55A
SAFETY & WARNINGS
CAUTION:Rated weight for the TV stand is 33kg (77 lbs). The rated weight for the storage shelf is 5kg (11 lbs).Use with products heavier than the rated weights indicated may result in instability causing possible injury.
- Please closely follow the assembly instructions. Improper installation may result in damage or serious personal injury.
- Safety gear and quality tools must be used.
- When in use, make sure the stand is on a flat level surface and the caster wheels are locked.
- Do not allow children to play near this stand.
- This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
- A minimum of two people are recommended for this installation. Failure to use safety gear and safe working methods may result in property damage, serious injury or death.
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, contact your place of purchase for a replacement.MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at least every three months).
Suitable for TVs 32″ – 55″ maximum
VESA compatibility:100×100, 200×100, 200×200, 300×200, 300×300, 400×200, 400×300, 400×400
COMPONENTS
Stand assembly:
A (x1) B (x2)
C (x1) D (x1)
E (x1) F (x1) G (x1) H (x1)
I (x1) J (x4) K (x1) L (x1)
M (x2) N M6x50 (x4) O M6x35 (x4) P M6x16 (x11)
Q (x8) R (x1) S (x1) T (x1)
Adapters (Depends on TV):
M-A M5x14 (x4) M-B M6x14 (x4) M-C M6x30 (x4) M-D M8x30 (x4)
M-E M8x50 (x4) M-F (x4) M-G (x8) M-H (x8)
ASSEMBLY
Step 1: Assembling the base
Attach the cross-beam (C) to the two base beams (B), using the Allen key (S) to tighten the M6x16mm (P) and M6x35mm (O) screws in place as shown below.
After the cross-beam is secured, attach the locking caster wheels (J), using the spanner (T) to tighten. Once the casters are installed, clamp the locks down to ensure the stand does not move suddenly during the remainder of the assembly. Place the joint left and right joint covers (K, L) into position as shown below.
Step 2: Attaching the stand
Place the stand (A) and joint cover (I) into position on the cross-beam, securing it with x4 washers (Q) and M6x50mm screws (N). Use the Allen key (S) to tighten.
Warning: To adjust the height, pull the safety spring lock outwards (1) while pulling the column upward (2) at the same time. Always ensure the spring lock aligns with the keyhole, otherwise a sudden drop may occur resulting in injury or property damage.
Note: The MAX line found on the column indicate the highest position. Never go beyond the MAX line marking.
Step 3:
Insert the supporting M6x16mm screw (P) into the extended stand, tightening it with the Allen key. Insert the hole covers (R, M) in place.
Step 4:
Attach the mounting plate (D) to the front of the stand, securing it with x4 washers (Q) and M6x16mm screws (P), using the Allen key to tighten.
Step 5:
Attach the shelf (G) to the stand, securing it to the shelf mount (H) with M6x16mm screws (P). The shelf is suitable for use with laptops, DVD and Blu-ray players, hard drives, gaming consoles, or anything else as long as the weight limit (5 kg) is not exceeded.
Step 6:
Attach the mounting brackets to your TV. Depending on your TV, a combination of spacers (M-G, M-H) may be required to help create the correct amount of space for the brackets. Ensure the screws are fitted correctly into your TV’s VESA mount holes, and are not too long or too short in the back of the TV.
Also note that the M-F adapter is used for both small screws (M-A, M-B) and large screws (M-C, M-D, M-E) depending on its orientation.
Step 7:
NOTE: Ensure the locking caster wheels (J) are locked before attempting to mount the TV.
With two people, lift the TV up and above the mounting plate and gently lower down into place, ensuring the TV is evenly positioned in the middle of the stand.
The brackets each feature a vertical screw to secure to the bottom of the mount. Hook this screw underneath the mount and tighten to secure.
A minimum of two people are recommended for this installation. Failure to use safety gear and safe working methods may result in property damage, serious injury, or death.
OPERATION
Cable Management:
The stand features built-in cable management functionality, as per the below image:
Tilting:
CAUTION: Loosen the knobs as shown and adjust the display to the desired angle, then tighten the knobs.
NOTES
Need more information?
We hope that this user guide has given you the assistance needed for a simple set-up.For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com
[xyz-ips snippet=”download-snippet”]