Kress KUY02P Impact Drill Instruction Manual

Kress KUY02P Impact Drill Instruction Manual

PRODUCT SAFETY GENERAL POWER TOOL SAFETY WARNINGS

PRODUCT SAFETY GENERAL POWER TOOL SAFETY WARNINGSWARNING Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. 

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery- operated (cordless) power tool.

1)Work area safety

  1. Keep work area clean and well Cluttered or dark areas invite accidents.
  2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or Power tools create sparks which may ignite the dust or fumes.
  3. Keep children and bystanders away while operating a power Distractions can cause you to lose control.

2) Electrical safety

  1. Power tool plugs must match the in serious personal injury.
  1. Use personal protective Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off-position before

connecting to power source and/or battery pack, picking up or carrying the tool.Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.

  1. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal
  2. Do not Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
  3. Dress properly. Do not wear loose clothing or Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
  4. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly Use of dust collection can reduce dust- related hazards.

Never modify the plug in any way. Do

  1. Do not let familiarity gained from           

not use any adapter plugs with earthed

frequent use of tools allow you to become                    3(grounded) power tools. Unmodified plugs and

complacent and ignore tool safety

matching outlets will reduce risk of electric shock.

  1. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or
  2. Do not expose power tools to rain or wet Water entering a power tool will increase the risk of electric shock.
  3. Do not abuse the Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
  4. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric
  5. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected Use of an RCD reduces the risk of electric shock.

3) Personal safety

  1. Stay alert, watch what you are doing and use common sense when operating a power Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result

principles. A careless action can cause severe injury within a fraction of a second.

4) Power tool use and care

  1. Do not force the power Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
  2. Do not use the power tool if the switch does not turn it on and Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
  3. Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool
  4. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power Power tools are dangerous in the hands of untrained users.

e) Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the

power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

  1. Keep cutting tools sharp and Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be

performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

  1. Keep handles and grasping surfaces dry, clean and free from oil and Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

5) Service

  1. Have your power tool serviced by a qualified repair person using only identical replacement This will ensure that the safety of the power tool is maintained.

DRILL SAFETY WARNINGS

1 ) Safety instructions for all operations
  1. a) Wear ear protectors when impactExposure to noise can cause hearing loss.

4          b) Use auxiliary handle(s).Loss of control can cause personal injury.

  1. c) Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory or fasteners may contact hidden wiring or its own Cutting accessory or fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

2)  Safety instructions when using long drill bits

  1. Never operate at higher speed than the maximum speed rating of the drill bit. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal

b) Always start drilling at low speed and with the bit tip in contact with the workpiece. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.

  1. Apply pressure only in direct line with the bit and do not apply excessive pressure. Bits can bend causing breakage or loss of control, resulting in personal

SYMBOLS

COMPONENT LIST

1. KEYLESS CHUCK
2. AUXILIARY HANDLE
3. HAMMER DRILL /DRILL SELECTOR DIAL
4. LOCK-ON BUTTON
5. ON/OFF SWITCH
6. FORWARD AND REVERSE ROTATION CONTROL

Not all the accessories illustrated or described are included in standard delivery

TECHNICAL DATA

Type designation KUY02P (Y02P-designation of machinery, representative of Impact Drill)

 

 

 

           

8

 Voltage 220-240V~50/60Hz
Rated input power 650W
Rated no load speed 0~3000/min
Impact rate 0-45000bpm
Chuck capacity 13mm
 

Max drilling capacity

 Steel 13mm
Concrete 13mm
Wood 25mm
Machine weight 1.69kg
Protection class  /ll

ACCESSORIES

Auxiliary Handle                                    1Depth Gauge                                         1

We recommend that you purchase your accessories listed in the above list from the same store that sold you the tool. Refer to the accessory packaging for further details. Store personnel can assist you and offer advice

OPERATING INSTRUCTIONS

NOTE: Before using the tool, read the instruction book carefully.

INTENDED USE

The machine is intended for hammer drilling in brick, concrete and stone. It is also suitable for drilling without impact in wood, metal and plastic.

ASSEMBLY AND OPERATION

Action FIGURE
Clamp and release the auxiliary handle

WARNING! To avoid accidents, please be sure

to check and tighten the handle before use.

  

 

See Fig. A1,A2
Chuck Adjustment See Fig. B1,B2
Connect the power See Fig. C
On/off switch and lock-on button See Fig. D
Forward and reverse rotation control Note: Do not move the forward and reverse rotation control when the drill is working or the switch is locked to avoid damage to the drill.  

 

See Fig. E
Hammer drill /drill selector dial See Fig. F

1. WORKING HINTS FOR YOUR TOOL

  1. FOR DRILLING OF STONES AND CONCRETE Set the hammer/drill control button to the “hammering” Tungsten carbide drill bits are used for rapid drilling of stones and concrete.

2.  FOR DRILLING OF STEEL

Set the hammer/drill control button to the “drilling” position. High-speed steel drill bits are used for drilling of steel in a slow manner.

3.  FOR LOCATING HOLES

When drilling large holes in rigid materials such as steel, it is recommended to drill a small locating hole before using a large drill bit.

4.  FOR DRILLING OF TILES

Set the hammer/drill button to the “drilling” position. After penetrating the porcelain, set to the “hammering” position

1.  COOLING MOTOR

If your power tool becomes over heated, set the speed to maximum and run no load for 2-3 minutes to cool the motor.

MAINTENANCE

Remove the plug from the socket before carrying out any adjustment, servicing or maintenance.

Your power tool requires no additional lubrication or maintenance.There are no user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls free of dust. Occasionally you may see sparks through the ventilation slots. This is normal and will not damage your power tool.If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

PROBLEM SOLUTION

  1. If the drill does not work, please check if the power plug is connected firstly.
  2. If the drilling effect is poor, check whether the drill bit is If any wear, replace the drill bit. Check whether the drill is set to “forward rotation” position    9 under normal use.
  3. If it cannot be resolved, please return the drill to your local dealer for
report this ad

Positec Australia Pty Limited 10 Corporate Blvd Bayswater, VIC 3153, Australia

 

 

Read More About This Manual & Download PDF:

References

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

, , , , ,