Leggett Platt 18 Button PT – Glass Top Remote Control User Guide
Product Overview
SNORE BUTTONPress and hold to raise head to the preprogrammed position. Head will automatically lower to flat after 15 minutes.
- To program a position, adjust base to desired position, press and hold the set button until the massage motors and underbed light turn on and off, then press and hold the Snore button until the massage motors turn on and off.
HEAD UP/DOWN BUTTONPress and hold to raise or lower the head section.
PILLOW TILT UP/DOWN BUTTONPress and hold to raise or lower the pillow tilt section.
SET BUTTONPress and hold to program M1, M2 and Snore presets
HEAD MASSAGE UP/DOWN BUTTONPress to increase or decrease massage intensity. Massage has 3 speeds: Low, medium and high. Massage will automatically shut off after 15 minutes.
MASSAGE ON/OFF BUTTONPress “on” to turn both massage motors on. Press “off” to turn both massage motors off.
FLAT BUTTONPress and hold to lower the base to the level position.
UNDERBED LIGHT BUTTONPress to turn underbed light on. Press again to turn underbed light off.
LOCK BUTTONPress to lock remote control. Press again to unlock remote control.
FOOT UP/DOWN BUTTONPress and hold to raise or lower the foot section.
M1 BUTTONPress and hold to adjust base to the programmed position.
- To program a position, adjust base to desired position, press and hold the set button until the massage motors and underbed light turn on and off, then press and hold the M1 button until the massage motors turn on and off.
M2 BUTTONPress and hold to adjust base to the programmed position.
- *To program a position, adjust base to desired position, press and hold the set button until the massage motors and underbed light turn on and off, then press and hold the M2 button until the massage motors turn on and off.
FOOT MASSAGE UP/DOWN BUTTONPress to increase or decrease massage intensity. Massage has 3 speeds: Low, medium and high. Massage will automatically shut off after 15 minutes.
NOTE REMOTE CONTROL REQUIRES (3) AAA SIZE BATTERIES.
TOUCH & HOLD TO ONE TOUCH
Note: If using 2 remotes to operate 1 or more bases, both remotes must be set to the same “touch & hold” or “one touch” mode.To change remote control functions from “touch and hold” to “one touch” (“one touch” = touch and release), simultaneously touch the HEAD MASSAGE DOWN and FOOT MASSAGE DOWN buttons for 5 seconds. The massage motor and underbed light will turn on and off confirming the change. Your base is now set to “one touch.”
When in “one touch” mode:M1, M2, and Snore buttonsTouch and release (one touch) button. Base will adjust to the programmed position. Touch any other button to stop the base during movement.
Flat buttonTouch and release (one touch) button. Base will shut off massage motor, if active, and adjust base to level position. Touch any other button to stop the base during movement.To revert back to factory settings, simultaneously touch and hold the SET button and the FLAT button for 5 seconds. The massage motor will turn on and off confirming the change. Your base is now set to factory settings.
REMOTE CONTROL PROGRAMMING REMOTE TO OPERATE 1 BASE
STEP 1 Unplug base for 30 seconds, then plug back in.
STEP 2Remove the battery compartment door from the remote control (FIGURE 1).
STEP 3Push the LEARN BUTTON on the control box in two times (FIGURE 2). The underbed light will come on.
STEP 4Using a pointed object, press and hold the LEARN SWITCH on the remote control (FIGURE 1) until the underbed light goes off.
STEP 5Operate the remote control to verify the base functions correctly
REMOTE CONTROL PROGRAMMING – 1 OR 2 REMOTES TO OPERATE 2 BASES
Note: Make sure both remotes are in “touch & hold” mode before beginning procedure. If using 2 remotes, both remotes must be in the same “touch & hold” or “touch & release” mode.
STEP 1Plug both bases into power source. Operate each base with its respective remote control to verify the base functions properly. Lower both bases to the flat position.
STEP 2UNPLUG both bases.
STEP 3Place both bases on their sides close to each other.CAUTION: DUE TO RISK OF INJURY, TWO ADULTS ARE REQUIRED TO HANDLE AND MOVE ADJUSTABLE BASE.
STEP 4Locate the sync cable (FIGURE 3).
STEP 5Unplug the existing cable from the MFP of the control box on both bases, then insert one male plug of the sync cable into the MFP of base 1 control box and the other male plug of the sync cable into the MFP of base 2 control box (FIGURE 4).
STEP 6Insert unplugged cable from base 1 into one female plug of the sync cable, then insert unplugged cable from base 2 into the other female plug of the sync cable (FIGURE 4).
STEP 7Turn both bases over onto their legs.CAUTION: DUE TO RISK OF INJURY, TWO ADULTS ARE REQUIRED TO HANDLE AND MOVE ADJUSTABLE BASE.CAUTION: MAKE SURE SYNC CABLE IS NOT CAUGHT IN BASE OR PINCH POINTS.
STEP 8Plug both bases back into power source.
STEP 9Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare.Note: If bases do not operate in unison with the remote, verify sync cable connections are fully seated in both MFP ports. Unplug both bases, wait 10 seconds, then plug bases back in.
REMOTE CONTROL PROGRAMMING – SEPARATING 2 BASES (INDEPENDENT MOVEMENT)
STEP 1UNPLUG both bases.
- Remote Control 1
- Remote Control 2
STEP 2Place both bases on their sides close to each other.CAUTION: DUE TO RISK OF INJURY, TWO ADULTS ARE REQUIRED TO HANDLE AND MOVE ADJUSTABLE BASE.
STEP 3On both bases, remove the male plug of the sync cablefrom the MFP port on the control box (FIGURE 5).
STEP 4On both bases, remove the cable inserted into the femaleplug of the sync cable and insert it into the MFP port ofthe control box (FIGURE 6). Store sync cable for possiblelater use.
STEP 5Turn both bases over onto their legs.CAUTION: DUE TO RISK OF INJURY, TWO ADULTS ARE REQUIRED TO HANDLE AND MOVE ADJUSTABLE BASE.
STEP 6Plug both bases back into power source. Remote control 1 should now operate base 1 and remote control 2 should now operate base 2. If they do not, refer to Remote Control Programming – 1 Remote to Operate 1 Base.
POWER DOWN OPERATION
Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use.Note: Power down device uses 9-volt alkaline batteries, which are not included.
STEP 1Unplug base from electrical source.STEP 2Insert (2) 9-volt alkaline batteries into the power brick (FIGURE 7).
STEP 3Press the HEAD DOWN BUTTON, PILLOW DOWN BUTTON, and the FOOT DOWN BUTTON on the remote control until each section is flat (FIGURE 8).
STEP 4Remove batteries from power brick and discard. Note: Batteries are good for only one use.When power is restored from outage, plug base into power source. Base is ready to resume normal operation.
TROUBLESHOOTING
If the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:
|
SYMPTOM |
SOLUTION |
|
Remote control illuminates and appears to be operable, but will not activate base. |
|
|
No features of the base will activate. |
|
| Remote control will not illuminate. |
|
|
Head or foot section will elevate, but will not return to the horizontal (flat) position. |
|
|
Excessive massage motor noise. |
|
ADVISORY
IMPORTANT INFORMATION
READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT
WARNING
FOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED). FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.
ELECTRICAL RATINGElectrical components are rated for 100-240V, 50-60Hz, 1.5A.ELECTRICAL GROUNDINGThis product is equipped with a polarized or grounded electrical power cord. The power cord will only fit into a grounded, electrical surge protection device (not included) or a grounded electrical outlet.
WARRANTY WARNING
Do not open any control boxes, motors or remote control devices (with the exception of the remote control and power down box battery compartments). The product warranty will be void if these components are tampered with. Do not attempt to alter component wiring or adjust or modify the structure of the product in any way or the warranty will be void. Any repair or replacement of base parts must be performed by authorized personnel.
LUBRICATIONThis product is designed to be maintenance free. The lift motors are permanently lubricated and sealed—no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.
SMALL CHILDREN / PETS WARNINGAfter the base is unboxed, immediately dispose of packaging material as it can smother small children and pets. To avoid injury, children or pets should not be allowed to play under or on the base. Children should not operate this base without adult supervision.
MASSAGE OPERATION
The massage feature will emit a minimal tone during operation. This is normal. When the massage level is increased, motor resonance will intensify accordingly.
LOCATION ENVIRONMENTThe level of sound experienced during operation is directly related to the location environment. For example, when a base is located on a hardwood floor with the massage feature in operation, a vibrating tone will be audible.
PRODUCT RATINGSThe base lift motors are not designed for continuous use. Reliable operation and full life expectancy will be realized as long as the lift motors do not operate any more than five (5) minutes over a forty-five (45) minute period, or approximately 11% duty cycle. Note: Massage equipped bases are not designed for continuous, extended massage operation. Massage systems are rated for a maximum of 2 hours of use within any 6 hour period. Any attempt to circumvent or exceed product ratings will shorten the life expectancy of the product and may void the warranty.
The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position.Avoid placing entire weight on head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME.
UL (Underwriters Laboratories) recognized components. Adjustable base is tested to UL (Underwriters Laboratories) standards. CFR 1633 approved for use with most mattresses.
ADVISORY
IMPORTANT INFORMATION
READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT
HOSPITAL USE DISCLAIMER
This base is designed for in-home use only. It is not approved for hospital use and does not comply with hospital standards. Do not use this base with tent type oxygen therapy equipment, or use near explosive gases. Manufacturer makes no representation or warranty that the adjustable base constitutes a medical device or is suitable for medical or therapeutic use.
SERVICE REQUIREMENTSService technicians are not responsible for moving furniture,removing headboards and footboards or any items required toperform maintenance on the base. In the event the technician is unable to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.
LIFTING/LOWERING MECHANISMSThe lift/lower feature will emit a minimal humming sound during operation. This is normal.
During operation, the lift arm wheels make contact with the platform support of the base. This applies slight tension on the moving components and resonance is reduced to a minimum level. If excessive noise or vibration is experienced, reverse the movement action (up or down) of the base with the remote control. This should realign the base’s activating mechanisms to the proper operational position.
FABRIC CLEANING INFORMATIONSpot clean only with water based shampoo or foam upholstery cleaner. Pretest a small, inconspicuous area before proceeding.Do not over wet. Do not use solvents to spot clean. Pile fabrics may require brushing with a non-metallic, stiff bristle brush to restore appearance. Hot water extraction or steam cleaning is not a recommended cleaning method.
To prevent overall soiling, frequent vacuuming or light brushing with a non-metallic stiff bristle brush to remove dust and grime is recommended. When cleaning a spill, blot immediately to remove spilled material. Clean spots or stains from the outside to the middle of the affected area to prevent circling. Use a professional furniture cleaning service when an overall soiled condition is apparent.
PACEMAKER WARNINGThis product produces a vibrating sensation. It is possible that individuals with heart-assist pacemakers may experience a sensation similar to exercise. Consult physician for complete information.
FCC COMPLIANCEThe equipment has been tested and found to comply with thelimits for a Class B digital device, pursuant to Part 15 of theFCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning off the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Radio Frequency = 2.4 GHz.
report this ad
CUSTOMER SERVICE toll free: (800) 888-3078
[xyz-ips snippet=”download-snippet”]