Junior Jungle Tanzania
USER MANUALJunior Jungle TanzaniaWARNING: The disassembled product may contain small parts which pose a choking hazard to children under 3. IMPORTANT:This product may contain sharp points and small parts prior to assembly. The owner’s manual contains safety, assembly, use and maintenance instructions. This product must be assembled by an adult who has read and understood these instructions. Keep the packaging away from children and dispose of all packaging before use. For the installer and your children’s safety, it is important to fully read and understand the instructions and safety hazards before commencing the assembly of the product. NOTE: This manual should not be used to guide your purchasing decision. Your product, and the contents inside its carton, may vary from what is listed in this manual. This manual may also be subject to updates or changes. Updated manuals are available through our website at www.lifespankids.com.au.
TABLE OF CONTENTS
I. GENERAL SAFETY INSTRUCTIONS
3
1.1 Danger for Children
3
1.2 Risk of Injuries
3
1.3 Product Damage
3
1.4 Assembly Advice
4
II. SAFETY INSTRUCTIONS
5
III. ASSEMBLY INSTRUCTIONS
7
3.1 Monkey Bars – Parts List
7
3.2 Set Up
8
3.3 Climbing Net & Rope – Parts List
15
3.4 Swing Set – Parts List
19
IV. MAINTENANCE
25
V. WARRANTY
26
I. GENERAL SAFETY INSTRUCTIONSNOTE: This product is intended for outdoor domestic use only.1.1 DANGER FOR CHILDRENWARNING: No eating while using the product at the same time.· Children do not recognize potential dangers from this product. The unassembled product must be stored out of reach of children and pets.· This product may only be used with adult supervision at all times. · The packaging material is not suitable for children due to choking and suffocationhazards.1.2 RISK OF INJURIES · Do not use the product if it is damaged or defective. If it is damaged or defective, please contact a qualified technician. · Check the product before each use. Defective parts must be changed immediately as they can impair the function and the safety of the product. · No more than one person to use the product at the same time. · Use the product only on even and non-slipping surfaces. Never use it near water and keep sufficient space around for safety. · Beware of moving parts such as the springs or elastics, which could catch your arms and legs. Do not place any objects or body parts in the product’s openings.1.3 PRODUCT DAMAGE · Do not make alterations to the product. Only use original spare parts. Qualified technicians should only carry out repairs improper repairs can lead to danger for the user. Use this product only as described in this manual.GENERAL SAFETY INSTRUCTIONS 3
1.4 ASSEMBLY ADVICE· The assembly of the product must be done carefully and by an able-bodied adult. If in any doubt, ask a technically qualified person.· Before you start with the assembly, read the instructions carefully. · Remove all packaging materials and lay down all parts on an open space.This gives you an overview and simplifies the assembly procedure. · Check with the parts list that all parts are available. Dispose of the packaging materialwhen the assembly is completed. · Beware that when using tools or doing technical work, there is always a risk of injuries.Assemble the product with care. · Create a danger free environment; for example, do not let tools lay around the workspace.Store the packaging material in a way that cannot cause any danger. · After installing the product according to the instruction manual, ensure all screws, bolts andnuts are correctly installed and tightened and that all joints are secure. · Reasonable space must be kept between the product and possible sources of danger, suchas other equipment swimming pools and fences. · The product must be assembled correctly before use. · Your play structure must be installed on a flat horizontal surface with a minimum of 2mbetween it and any structure or obstacle such as a fence, garage house, tree branches, cloths lines, or electric cables. · Modifications made to the original product shall be carried out according to the instructions of the manufacturer.· The product must always be used in a well-lit area.· Do not place anything under the product.· Use gloves during assembly and disassembly.· Outdoor products should be equipped with a device that in strong wind conditions avoid displacement due to wind (e.g. steel bars in the ground or loads like sandbag or water bags).· In certain areas during winter, snow buildup and the low temperatures can damage the product. It is recommended to remove snow buildup and to store the product indoor.· We strongly recommend visual inspections every 3 months to ensure the integrity of the entire product. Replace any parts as necessary.4 GENERAL SAFETY INSTRUCTIONS
II. SAFETY INSTRUCTIONS· The safety instructions of the product should always be considered and obeyed.· Using the product may result in permanent injury such as paralysis, or even death. Falling off the product may lead to injuries, particularly to the back, neck or head.· No clothes with hooks or lose parts should be worn or carried during product usage in order to avoid hooks getting caught and causing injury.· Strong winds can result in the product being blown away or damaged. If strong winds are predicted the product must be disassembled and moved to a sheltered area or sufficiently anchored down.· Moving the product whilst assembled may affect the integrity of the frame. Should it be necessary to move the product, please consider the following:1. Force to be evenly spaced around the frame to lift the product off the ground. 2. The product must be carried horizontally. 3. Use caution whilst moving as it could bend the product frame.· Users should be familiar with the assembly manual. This manual contains assembly guidance; selected precautionary measures as well as recommendations for servicing and maintenance of the product, in order to ensure a secured and fun use of the product.· It is the responsibility of the owner or the supervisor to guarantee that all users of the product are informed sufficiently of all warning references and safety instructions.For the supervisorThe supervisor’s role is to make sure users are aware of all safety precautions and that these precautions are enforced. When a supervisor is not available, the product may be disassembled or covered to limit access.· The product can be only used if it is in good condition, worn or damaged parts should be replaced.· Objects, which could be dangerous to the user, should be away from the product. · Avoid unauthorized and unsupervised use of the product. · Do not use the product under influence of alcohol or drugs (incl. medicines). · Do not use the product as a jumping platform for other articles.SAFETY INSTRUCTIONS 5
Consumer Information Sheet for Playground Surfacing MaterialsThe US Consumer Product Safety Commission (CPSC) estimates that about 100 000 playground equipment-related injuries resulting from falls to the ground surface are treated annually in US hospital emergency rooms. Injuries involving this hazard pattern tend to be among the most serious of all playground injuries, and have the potential to be fatal, particularly when the injury is to the head. The surface under and around playground equipment can be a major factor in determining the injury-causing potential of a fall. It is self-evident that a fall on to a shock-absorbing surface is less likely to cause a serious injury than a fall onto a hard surface. Playground equipment should never be placed on hard surfaces, such as concrete or asphalt, and while grass may appear to be acceptable, it may quickly turn to hard-packed earth in areas of high traffic. Shredded bark mulch, wood chips, tine sand or the gravel are considered to be acceptable shock absorbing surfaces when installed and maintained at a sufficient depth under and around playground equipment.Table B.1 lists the maximum height from which a child would not be expected to sustain a lifethreatening head injury in a fall on to four different loose-fill surfacing materials if they are Installed and maintained at depths of 150 mm, 225 mm and 300 mm.
TABLE B.1: Fall height in millimetres from which a life-threatening head injury would not be expected.
TYPE OF MATERIALDouble Shredded Bark Mulch Wood Chips Fine Sand Fine Gravel
DEPTH OF SURFACING MATERIAL
150mm 1800 1800 1500 1800
225mm 3000 2100 1500 2100
300mm 3300 3600 2700 3000
However, it should be recognised that all injuries due to falls cannot be prevented, no matter what surfacing material is used.It is recommended that a shock absorbing material extend a minimum of 1800mm in all directions from the perimeter of stationary equipment such as climbing frames and slides. However, because children may deliberately jump from a moving swing, the shock absorbing material should extend in the front and rear of a swing a minimum distance of twice the height of the pivot point measured from a point directly beneath the pivot on the supporting structure.This information is intended to assist in comparing the relative shock-absorbing properties of various materials. No particular material is recommended over another. However, each material is only effective when properly maintained. Materials should be checked periodically and replenished to maintain correct depth as determined necessary for the equipment in question. The choice of a material depends on the type and height of the playground equipment, the availability of the material in a particular area, and its cost.
6 SAFETY INSTRUCTIONS
III. ASSEMBLY INSTRUCTIONS MONKEY BARS – PARTS LIST
FC 4914 X 2pcs. FC 4902 X 3pcs.
FC 4912 X 9pcs.
FC 4903 X 2pcs.
FC 4904 X 2pcs.
FC 4905 X 8pcs.
FC 4911 X 2pcs.
FC 4915 X 4pcs.
BR 01 12pcs.
BR 02 6pcs.
BR 03 5pcs.
E Anchor5pcs.
A M8X48MM18+1pcs.
B M8X50MM4pcs.
C M8X42MM13+1pcs.
D M8X60MM16+1pcs.
F M8X35MM18+1pcs.
ASSEMBLY INSTRUCTIONS 7
SET UPSTEP 1-1: FRAME & RUNGS ASSEMBLY Please pay attention to the hole direction, the big holes are inside for inserting rungs.
F M8 x 35MM
FC 4912 x 9
FC 4914 x 2
STEP 1-2: SUPPORT BARS ASSEMBLY ATTENTION: Do not over fasten bolts before complete assembly.CC M8 x 42MM FC 4915 x 48 ASSEMBLY INSTRUCTIONS
C C
STEP 2 ATTENTION: Do not over fasten bolts before complete assembly.
A C
A C
A
C
FC 4906 x 4
A C
FC 4902 FC 4902
FC 4902 FC 4902
POSITION 1: H1880MMA AB
POSITION 2: H1620MMBAB
FC 4902 TOP
POLE DIRECTIONASSEMBLY INSTRUCTIONS 9
STEP 3 ATTENTION: Do not over fasten bolts before complete assembly.
FC 4905 x 16
1
A
B AB A B
2
FC 4911 x 4
FC 4904 x 4 FC 4904 x 4
IMPORTANT NOTE:
Check page 13 for installing
A
the second monkey bar legs. One corner must not be
installed with Part A, B and C.
B
FC 5002
D x 32
C
C
C
10 ASSEMBLY INSTRUCTIONS
STEP 4 ATTENTION: Do not over fasten bolts before complete assembly. · The product should be installed over impact absorbing surfaces such as sand, wood-barchips, rubber and foam and should not be installed over concrete, asphalt or any hard surface. · Anchors shall be placed level with or under the ground in order to reduce tripping hazards.FC 4908 FC 4910
A
A
C
E x5
ASSEMBLY INSTRUCTIONS 11
COMBINATION B STEP 1 Step 1. Disassemble one of short leg on platform(FC4904), re-placed by a long leg(FC5002)and leg base needs to move to long Leg -FC5002. Step 2. Use bracket (BR 02) to fix the platform bar. ATTENTION: 1. DON’T fasten bolts until fully assembled. 2. DON’T over fasten bolts. 3. Before use, please check all bolts and fasten properly.STEP 1
FC 4904STEP 2FC 5002
POLE DIRECTION: FC5002
FC 5002 TOP
A A12 ASSEMBLY INSTRUCTIONS
STEP 2: TOP BRACKETS/SUPPORT BAR ASSEMBLY ATTENTION: Do not over fasten bolts before complete assembly2 adults for assembly
FC 5003 FC 5002
A M8 x 48mm1A A
C M8 x 42mm2C
FC 5002
FC 5002
ASSEMBLY INSTRUCTIONS 13
STEP 3: PLATFORM & ANCHOR ASSEMBLY ATTENTION: Do not over fasten bolts before complete assembly. · The product should be installed over impact absorbing surfaces such as sand, wood-barchips, rubber and foam and should not be installed over concrete, asphalt or any hard surface. · Anchors shall be placed level with or under the ground in order to reduce tripping hazards.
FC 4905 x 8 FC 4904 x 2
1
A
B
A
A BB
A B
FC 4903 x 2
FC 4911 x 2
2
D x 16
C
C
C
E x2
14 ASSEMBLY INSTRUCTIONS
CLIMBING NET & ROPE – PARTS LISTFC 5201 X 1pc. FC 5202 X 1pc. FC 5203 X 1pc. FC 5204 X 1pc. Climbing Rope – FC 5205 X 1pc.Climbing Net – FC 5206 X 1pc.
BR 02 10pcs.A M8X50MM10+1pcs.
BR 03 2pcs.C M8X42MM2pcs.
E Anchor2pcs.F U Bolts1pc.
ASSEMBLY INSTRUCTIONS 15
COMBINATION B STEP 1 Step 1. Lay out Frames (FC5204/5202/5203/5201) and Net (FC5206)as below.FC 5204
FC 5203
FC 5202
FC 5201Step 2. Insert frame through net loops as below. Repeat same actions for 4 sides.FC 5206
16 ASSEMBLY INSTRUCTIONS
COMBINATION B STEP 2 ATTENTION: 1. DON’T fasten bolts until fully assembled. 2. DON’T over fasten bolts. 3. Before use, please check all bolts and fasten properly.
POLE DIRECTION: FC5202
FC 5203
FC 5204 AFC 5201
A
COMBINATION B STEP 3
FC 5204 AFC 5202
FC 5201
A
FC 5205ASSEMBLY INSTRUCTIONS 17
COMBINATION B STEP 4AC18 ASSEMBLY INSTRUCTIONS
SWING SET – PARTS LIST
FC 5101 X 1pc.
FC 5102 X 2pcs.
FC 5103 X 2pcs.
FC 4908 X 2pcs.
FC 4909 X 1pc.
FC 4910 X 1pc.
FC 5104 X 1pc.
FC 5105 X 1pc.
BR 01 8pcs.
BR 02 6pcs.
BR 03 2pcs.
E Anchor6pcs.
A M8X48MM10+1pcs.
C M8X42MM7+1pcs.
F U Bolts4pcs.
ASSEMBLY INSTRUCTIONS 19
COMBINATION B STEP 5 ATTENTION: 1. DON’T fasten bolts until fully assembled. 2. DON’T over fasten bolts. 3. Before use, please check all bolts and fasten properly.POLE DIRECTION: FC5102
FC 5102 TOP
A A
FC 5101 FC 5102
FC 5103
20 ASSEMBLY INSTRUCTIONS
C C
COMBINATION B STEP 6 ATTENTION: 1. DON’T fasten bolts until fully assembled. 2. DON’T over fasten bolts. 3. Before use, please check all bolts and fasten properly.
A
A
CASSEMBLY INSTRUCTIONS 21
HANG POINTS FOR SWING SEATS, TRAPEZE BAR. 1. Hang method for Trapeze bar.2. Hang method for swing seat.
Lock nuts properly. ATTENTION: Lock ring is used for adjusting chain height.Lock both nuts properly.
>380mm Ground22 ASSEMBLY INSTRUCTIONS
HANG POINTS FOR SWING SEATS, TRAPEZE BAR. Option 1: Standard – Swing seat + Trapeze
3
2
1
Hang Point
Option 2: Hang points are available for 1m Diameter Web Swing (web swing not included)
3
2
1
Hang Point
ASSEMBLY INSTRUCTIONS 23
COMBINATION B STEP 7 ATTENTION: 1. Ensure anchors are properly fixed into ground. 2. Please carry on the anchor condition before use.Any loose condition, please re-fix anchors by other 2 holes provided.
24 ASSEMBLY INSTRUCTIONS
E x6
IV. MAINTENANCEWARNING: Please keep for future reference.We recommend regular maintenance to be conducted at the beginning of each season as well as at regular intervals during the usage session for your play equipment to ensure all main parts/fixings are tightly secured, well-oiled and intact to avoid failure, injury or hazards. GENERAL ADVICE It is of particular importance that this is followed at the beginning of each season as well as at regular intervals during the usage season. · Check the accessories monthly as well as the play equipment’s structure to prevent falling risks. · Check and retighten screws, bolts, and all other hardware elements as necessary.a. Do not over tighten to avoid damaging the thread or cracking the surrounding wood. · Check all coverings and bolts for sharp edges and replace when required. · Lubricate all moving metallic parts. · Equipment situated in a high moisture or high salt content locations are more likely to oxidantand rust. Regular checks should be done more often. When signs of oxidation and / or rust appear on various metallic parts of your equipment, sand rusted areas and tubular members and repaint using a non-lead-based paint when required. · Where applicable: check swing seats, chains, ropes, and other means of attachment for evidence of deterioration. · Replace when required in accordance with the owner’s manual. If your play structure is disassembled, be sure to clearly mark any attached metal plates to prevent accidents. Check all bolt covers and sharp edges and replace them if necessary. For longer accessory life, we suggest storing them during the winter.MAINTENANCE 25
V. WARRANTYAUSTRALIAN CONSUMER LAW Many of our products come with a guarantee or warranty from the manufacturer. In addition, they come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Full details of your consumer rights may be found at www.consumerlaw.gov.au. Please visit our website to view our full warranty terms and conditions: www.lifespankids.com.au/Warranty-Policy-KidsWARRANTY AND SUPPORT Any claim against this warranty must be made through your original place of purchase. Proof of purchase is required before a warranty claim may be processed. If you have purchased this product from the Official Lifespan Kids website, please visit www.lifespankids.com.au/warranty-form For support outside of warranty, if you wish to purchase replacement parts or request a repair or service, please visit www.lifespankids.com.au/warranty-form and fill in our Repair/Service Request Form or Parts Purchase Form.26 WARRANTY
www.lifespankids.com.au
References
[xyz-ips snippet=”download-snippet”]