IQxel-M8W Multi-DUT Connectivity Test System Specifications
General Technical Specifications
RF Analyzer
Parameter: Ports (A/B): Value
Input frequency range: RF1 to RF4: 400 to 6000 MHzIF bandwidth: RF1 to RF4: 160 MHzInput power range: RF1 to RF4: +30 dBm peak (+25 dBm average)Input power accuracy: RF1 to RF4: Specification: ± 0.75 dB (+25 to -75 dBm) Typical: ± 0.50 dB (+25 to -75 dBm)Input return loss: RF1 to RF4: >12 dB (400 to 6000 MHz)Spurious (signal applied)1: RF1 to RF4: < -60 dBc (CW, for signal levels greater than -20 dBm)Spectral flatness: RF1 to RF4: Specification: ≤ ± 1 dB ( ± 80 MHz) Typical: ± 0.50 dB ( ± 80 MHz)Inherent spurious floor (no signal): RF1 to RF4: ≤ -80 dBmNoise figure: – : ≤ 30 dB at minimum input attenuationIntegrated phase noise: – : ≤ 0.3 degrees (100 Hz to 1 MHz) (400 to 6000 MHz), 0.2 degrees (100 Hz to 1 MHz) typicalSignal to noise ratio: – : ≥ 55 dB 100 kHz RBWSampling data rate: – :10, 20, 40, 80, 160, 240 MHzWaveform capture duration: :at 10 MHz sampling data rate 9600 msat 20 MHz sampling data rate 4800 msat 40 MHz sampling data rate 2400 msat 80 MHz sampling data rate 1200 msat 160 MHz sampling data rate 600 msat 240 MHz sampling data rate 400 ms
RF Analyzer – Signal Trigger
Parameter: RangeAbsolute minimum value: Wideband: RF -30 dBm, Video: -40 dBmAbsolute maximum value: Limited by the maximum input powerTrigger relative threshold: 30 dBLevel accuracy: < ± 2 dB
Port Isolation
Measurement: DescriptionPort to Port Isolation:VSA-to-VSA (through path):100 dB, <2500 MHz, typical90 dB, >2500 MHz, typicalVSG-to-VSG (through path):90 dB, <2500 MHz, typical80 dB, >2500 MHz, typicalVSG-to-VSA (through and combined path):100 dB, <2500 MHz, typical80 dB, >2500 MHz, typical
Timebase
Measurement: Description
Oscillator type: OCXOFrequency: 10 MHzInitial accuracy (25°C, after 60 minute warm-up): < ± 0.05 ppmMaximum aging: < ± 0.1 ppm per yearTemperature stability: < ±0.05 ppm over 0oC to 55°C range, referenced to 25°CWarm-up time (to within ±0.1 ppm at 25°C): > 30 minutes
Wireless LAN 802.11a/b/g/n/p/j/ah/af, 802.11ac (Wi-Fi 5), 802.11ax1 (Wi-Fi 6) Measurement Specifications
Measurement: Description: Performance
EVM2:EVM averaged over payload based on standard requirements (Typical):Residual loopback EVM (full packet channel estimation): ≤ -50.5 dB (-2 to -15 dBm)Residual loopback EVM (preamble only channel estimation): ≤ -47.5 dB (-2 to -15 dBm)Residual VSA EVM (preamble only channel estimation): ≤ -48 dB (+20 to -15 dBm)Note:– Measured at 5755 MHz– Averaged over 20 packets– 802.11ax waveform, 80 MHzPeak power: Peak power over all symbols (dBm): .
RMS power:All: average power of complete data capture (dBm)No gap: average power over all symbols after removal of any gap between packets (dBm):VSA power accuracy: ± 0.75 dB (+20 to -75 dBm).Max avg power:Peak value of the amplitude as a moving average over 40 samples (dBm): VSA power accuracy: ± 0.75 dB (+20 to -75 dBm)
I/Q amplitude error: I/Q amplitude imbalance (%) and approximate contribution to EVM (dB): .
I/Q phase error:I/Q phase imbalance (degrees) and approximate contribution to EVM (dB): .
Frequency error: Carrier frequency error (kHz): VSA measurement error: ≤ ± 0.2 ppm calibrated .
802.11ax (Wi-Fi 6) Waveform Generation
Feature: Specification
Uplink Single User OFDMA (SU-OFDMA)Downlink Single User OFDMA (SU-OFDMA)Uplink Multi User OFDMA (MU-OFDMA)Downlink Multi User OFDMA (MU-OFDMA)Multi-User MIMO + MU-OFDMA:Up to 160 MHzConfigurable Guard Interval.
Trigger Frame Waveform Generation with configurable power levels per RU, and user configurable fields: Up to 12 dB between users
Waveform Generation with DCM (Dual Carrier Modulation) and LDPC support: .
MIMO System Performance
The additional specifications in the table below apply to the complete IQxel-M8W MIMO system.
Measurement: Range
VSA capture trigger accuracy: ≤ ± 3.5 nsVSA start trigger accuracy: ≤ ± 3.5 ns
Measurement: Range
Test Capability: Carrier-to-noise ratioOutput frequency range:GPS: 1575.42 MHz (fixed)GLONASS: 1598 to 1606 MHzCOMPASS: 1561.098 (+/- 2.046) MHzGalileo: 1559 to 1593 MHzNumber of simultaneous channels: 1Output power range2: -60 to -95 dBmLevel accuracy: ± 0.75 dB
Port Descriptions
Front Panel
I/O: Function: Type
Power switch: Power on/off: Pushbutton switchRF1A/RF1B: RF input/output: N femaleRF2A/RF2B RF: input/output: N femaleRF3A/RF3B RF: input/output: N femaleRF4A/RF4B RF: input/output: N femalePower indicator: LED green – powered up, running, LED orange – powered up, standby: LED indicatorSession active indicator: LED green – remote session active, LED red – remote session lock: LED indicatorStatus indicator: LED green – no faults/errors detected, LED orange – Software error detected, LED red – Hardware fault detected: LED indicatorRF port 1 A/B indicator: Indicates port input/output status: LED indicatorRF port 2 A/B indicator: Indicates port input/output status: LED indicatorRF port 3 A/B indicator: Indicates port input/output status: LED indicatorRF port 4 A/B indicator: Indicates port input/output status: LED indicatorUSB (2 ports): USB 2.0 compatible connection to external controller: USB Type A
Rear Panel
General I/O
I/O: Function: Type
10 MHz ref input: 10 MHz reference input the 10 MHz reference input has a 200 ohm impedance and accepts a sine wave ranging in amplitude from 0.3 Vpp to 4 Vpp.: BNC female10 MHz ref output 10 MHz reference output: BNC femaleMarker out / trigger in 1: TTL compatible: BNC femaleMarker out / trigger in 2: TTL compatible: BNC femaleMarker out / trigger in 3: TTL compatible: BNC femaleMarker out / trigger In 4: TTL compatible: BNC femaleUSB (2 ports): USB 2.0 compatible connection to external controller: USB Type AAC in: AC power input: 100 to 240VAC (automatically switched) 50 to 60 Hz, Includes hard power switchDVI port: Display Litepoint monitor: DVI-DVGA port: Display Litepoint monitor: VGA-15 pinCommunication I/O LAN: 1000 Base-T LAN: RJ-45GPIO: General purpose input/output: 50-pin connector
General and Environmental
Dimensions: 14.5” W x 3.2” H x 20.5” D (368 mm x 82 mm x 521 mm)Weight: 11.4 kg (25.2 pounds)Power requirements: 100 to 240 VAC, < 300 W, 50 to 60 HzPower consumption: <235 W (maximum), <10 W (standby)Recommended PC: Intel Core i5 2.5 GHz with 4 GB of RAM or betterRecommended browser for optimal performance: Google Chrome R10 ReleaseOperating temperature: +10°C to +50°C (IEC EN60068-2-1, 2, 14)Storage temperature: -20°C to +70°C (IEC EN60068-2-1, 2, 14)Specification validity temperature1: +20°C to +35°COperating humidity: 15% to 95% relative humidity, non-condensing (IEC EN60068-2-30)EMC: EN 61326 Immunity for industrial environment, Class B emissionsSafety: IEC 61010-1, EN61010-1, UL3111-1, CAN/CSA-C22.2 No. 1010.1Mechanical vibration: IEC 60068, IEC 61010 and MIL-T-28800D, class 5Mechanical shock: ASTM D3332-99, Method BRecommended calibration cycle: 12 monthsWarranty: 12 months hardware, 12 months software updates
Order Codes
Code: Product
0100-IXMW-001: IQxel-M8W Test System with 8 RF ports active. Includes WLAN measurement suite software for SISO 802.11a/b/g/n/j/p0100-IXMW-002: IQxel-M8W Test System with 4 RF ports active.Includes WLAN measurement suite software for SISO 802.11a/b/g/n/j/p0300-IXMW-001: 802.11ac VHT80 (80MHz signal bandwidth) software license0300-IXMW-057: 802.11ac VHT160 (80+80MHz and 160MHz signal bandwidth) software license (Requires 802.11ac VHT80 license)0300-IXMW-069: 802.11ax software license (Requires 802.11ac VHT80 license for 80MHz signal bandwidth or 802.11ac VHT160 license for 160MHz signal bandwidth)0300-IXMW-061: WLAN MIMO software license. Enables MIMO option for 802.11n, 802.11ac, and 802.11ax (Requires associated 802.11 technology license)0150-IXMW-003: WLAN MIMO kit. Includes MIMO software license and tester synchronization cables0300-IXMW-003: Sequence Based Test (SBT) software license, also enables Trigger Based Test (TBT) for 802.11ax0300-IXMW-089: WiFi Traffic Sniffer software license (Requires 802.11ax license)0300-IXMW-002: Bluetooth measurement suite software license. Supports Bluetooth 1.0 – 4.x0300-IXMW-071: Bluetooth 5 measurement suite software license (Requires Bluetooth 1.0 – 4.x license)0300-IXMW-008: Zigbee measurement suite software license. Includes measurement capability for Zigbee, Wi-SUN and Z-wave0300-IXMW-009: DECT measurement suite software license0300-IXMW-044: 802.11ah measurement suite software license0300-IXMW-059: 802.11af measurement suite software license0300-IXMW-065: Sigfox measurement suite software license0300-IXMW-055: LTE measurement suite software license
CONTACT INFORMATION
LitePoint Corporation 575 Maude Court Sunnyvale, CA 94085-2803United States of America +1.866.363.1911/ +1.408.456.5000LITEPOINT TECHNICAL SUPPORT www.litepoint.com/support
Doc: 1075-0104-001January 2019 Rev 14
IQxel-M8W Multi-DUT Connectivity Test System Specifications Manual – IQxel-M8W Multi-DUT Connectivity Test System Specifications Manual –
[xyz-ips snippet=”download-snippet”]