Lorex D241 Series 1080p HD Security DVR User Manual

Table of Contents

Setting Up Your Recorder

See the steps below (expanded instructions to the right) to complete initial setup of the recorder:

For camera compatibility information, visit lorex.com/compatibility. * Not included / sold separately

Overview of extra ports:

NOTE: For full instructions on using the extra ports, please refer to your security recorder’s instruction manual at lorex.com.

Need Help?Visit us online for up-to-date softwareand complete instruction manuals.

Copyright © 2019 Lorex CorporationAs our products are subject to continuous improvement, Lorex reserves the right to modify product design, specifications and prices, without notice and without incurring any obligation. E&OE. All rights reserved.

Back panels shown below are for illustration only. Your recorder’s back panelmay appear different, with all the same ports in different locations.

STEP 1: Connect cameras*

Test your cameras prior to selecting a permanent mounting location by temporarily connecting the cameras and cables to your DVR.

NOTES:

The extension cable must be a single stretch of cable between the recorder and camera. You cannot connect multiple extension cables to each other.
This guide covers connecting cameras to your security recorder only. For full instructions on installing yourcameras, please refer to your camera’s documentation at lorex.com.
Before selecting a permanent mounting location for your cameras, see Ensuring Accurate Person andVehicle Detection below for important camera installation notes.

STEP 2: Connect router*

Connect the recorder to your router using the included Ethernet cable.

NOTE: To receive automatic firmware updates and enable remote viewing with mobile apps, a high speed Internetconnection is required (minimum upload speed of 3.5Mbps required for remote viewing). All other system features can be used without an Internet connection.

STEP 3: Connect mouse

Connect the included mouse to a USB port on the recorder.

STEP 4: Connect monitor*

Connect the recorder to a monitor using the included HDMI cable or a VGA cable (not included).Both HDMI and VGA ports support up to 1080p output resolution.

IMPORTANT: The system will automatically match the resolution of the connected monitor the first time you usethe recorder. If you need to switch monitors, make sure you set the recorder to an output resolution supported by the new monitor before switching. See Changing the Recorder’s Output Resolution on the rear for details.

STEP 5: Connect power

Use the included power adapter to connect the recorder to a nearby outlet. Turn the recorder on using the power switch on the back panel.

STEP 6: Lorex Setup Wizard

When you first power up your recorder, the Lorex Setup Wizard will begin. The Wizard will help you configure core system settings.You will also create a secure password. For future reference, it is recommended that you record your password here:

Record your password below and store in a secure place:

Ensuring Accurate Person and Vehicle Detection

The following are important camera installation notes to ensure accurate person and vehicle detection. For full camera mounting instructions, see your camera’s documentation at lorex.com.

Angle the camera so that objects of interest appear in the bottom ⅔ of the camera image.
Choose a location where objects of interest will be no further than 50ft (~15m) from the camera. Lower accuracy for objects further away than 50ft(~15m) and/or in the top ⅓ of the image Optimal accuracy for objects within 50ft (~15m)and in the bottom ⅔ of the image.
Angle the camera between 30~60° down from the level position.
Install the camera between 8-16ft (2.5-5m) off of the ground.

NOTE: Accuracy of person and vehicle detection will be influenced by multiplefactors, such as the object’s distance from the camera, the size of theobject, and the height and angle of the camera. Night vision will also impactthe accuracy of detection.

Additional Installation Tips:

Point the camera where there is the least amount of obstructions (e.g., tree branches).
Install the camera where vandals cannot easily reach.
Secure cabling so that it is not exposed or easily cut.
This camera is rated for outdoor use. Installation in a sheltered location is recommended.

Once you have completed all steps for initial setup on the front of this guide, please refer to the following sections to learn more about using your system.

Using the Mouse

During split-screen display mode: Click an individual channel to view it in full-screen. Click again to return to the splitscreen display mode.
While navigating menus: Click to open a menu option.
During live view: Click anywhere on the screen to open the QuickMenu.
While navigating menus: Click to exit menus.

During live view: Use the scroll wheel to zoom in / out.

NOTE: In live view, hover the mouse cursor over the top of the screen to open the Navigation Bar. Move the mousecursor away from the top of the screen to close the Navigation Bar.

Quick Access to System Information

Right-click anywhere on the live viewing screen to open theb Quick Menu. a. Open Main Menu.b. Search and playback recordings.c. Control PTZ cameras (not included).d. Select camera / live display view.e. View previous / next channel(s).f. View system information.g. Start/stop sequence mode.h. Temporarily disable all current audible warnings.i. Open manual recording controls.j. Adjust camera color and image settings.

Changing the Recorder’s Output Resolution

The system will automatically match the resolution of the connected monitor the first time you use the recorder.

IMPORTANT: If you need to switch the monitor, make sure you set the recorder to an output resolutionsupported by the new monitor before switching.

To change the recorder’s output resolution:

From live view, right-click and then click Main Menu. If prompted, log in using the system user name (default:admin) and your new, secure password.
Click DISPLAY, then configure the following:

a. Set Resolution to match the highest resolution supportedby your monitor. For example,select 1920×1080 for 1080pmonitors, or 1280×720 for 720p.b. Click Apply. The recorder willrestart before changes takeeffect.

Playback

Search through and play video recordings from the hard drive.To search for and play recordings:

From live view, right-click and then click Playback. If prompted, log in using the system user name (default:admin) and your new, secure password.
Configure the following:a. Use the calendar on the right toselect the date to playback.b. Check channels you want toplay back. Click the icon besideeach selected channel to selectMainstream (M) or Substream (S) video quality.c. Click inside the video bar to selectthe playback time. Playback startsimmediately at the selected time.

To filter for person / vehicle recordings:

PREREQUISITE: You must enable Smart Motion Detection on any and all channels you would like to filterfor person / vehicle detection. See the section Motion & Advanced Person/Vehicle Detection for details.

d. Click to stopcurrent playback.

e. Hover over the icon. Check Person / Vehicle to filter available playback events.Wait a few seconds for the video bar to show detection events.

Backup

Back up recordings from the hard drive to a USB flash drive (not included).

To back up recordings:

Insert a formatted USB flash drive (not included) into a free USB port on the recorder.
From live view, right-click and then click Main Menu. If prompted, log in using the system user name (default:admin) and your new, secure password.
Click BACKUP.
Configure the following:

a. Select your USB drive and thefolder for the backup. b. Select the channel(s) andrecording types to search by.c. Select a start and end time.d. Choose a file format.e. Click Add to see recordings thatmatch your search.f. Check boxes next to recordingsyou want to back up.g. Click Backup.

Motion & Advanced Person/Vehicle Detection

Set preferences for motion detection. This section includes setup of person/vehicle detection. By default, person/vehicle detection is enabled on channels 1 and 2.

To configure motion & advanced person/vehicle detection:

From live view, right-click and then click Main Menu. If prompted, log in using the system user name (default:admin) and your new, secure password.
Click ALARM. Click MOTION on the far-left, then click the Motion Detect tab.
Configure the following:

a. Select the channel you would like to configure.b. Click Enable.c. Click Setup next to Area to set an active area for motiondetection. See Figure 1 below for details.d. Click Setup next to Schedule to set the weekly schedulefor motion detection. See Figure 2 below for details.e. Set preferences for how the systemreacts to motion detection events.f. Click Smart Motion Detection toenable person / vehicle detection.See Figure 3 below for details.g. Click Apply to save changes.

The camera image appears with a red grid overlay.This means the entire image is enabled for motiondetection.

Click or click-and-drag to add / remove boxesfrom the active area. Cells that have beenremoved from the active area appear green.
Hover near the top of the image to reveal zoneselection. You can set up to 3 different zones withdifferent sensitivity and threshold values.
Right-click when finished.

Figure 1: Motion Detection Area

Figure 2: Motion Schedule

The default schedule, shown in Figure 2, isactive at all times.
Click Modify to change the schedule for thecorresponding day of the week.
Click OK when finished.

Figure 3: Smart Motion Detection

Click Enable to allow detection of people and vehicleson the selected channel.IMPORTANT: A maximum of 2 channels will supportperson/vehicle detection at once. By default, channels1 and 2 have person/vehicle detection enabled.
Select a Sensitivity level (a high sensitivity value willdetect smaller objects than a low value).
Check Person / Vehicle.
Click OK when finished.

Configuring Deterrence Settings

Set preferences for automatic warning light triggering on compatible Lorex deterrence cameras.For a complete list of compatible deterrence cameras, navigate to your recorder series at lorex.com/compatibility.

To configure deterrence settings

In live view, right-click and click Main Menu. If prompted, log in using the system user name (default: admin)and your new, secure password.
Click ALARM. Click MOTION on the far-left, then click the Deterrence tab.
Configure the following

a. Select the channel of a connecteddeterrence camera.b. Check Enable.c. Click Setup next to Warning Light toconfigure preferences.d. Click Setup next to Area to set an active area for automaticdeterrence. See Figure 4 below for details.e. Click Setup next to Schedule to set the weekly schedule forautomatic deterrence. See Figure 5 below for details.f. Click Apply.

Figure 4: Deterrence Area

The camera image appears with a grid overlay. Thegreen area is the active area for deterrence.
Click or click-and-drag to add / remove boxes fromthe active area.
In Figure 4, only motion around the doorway willtrigger warning light.
Right-click when finished.

Figure 5: Deterrence Schedule

The default schedule, shown in Figure 5, isactive during the night, between 5pm and7am.
Click Modify to change the schedule for thecorresponding day of the week.
Click OK when finished.

To set off all connected deterrence cameras’ warning lights andsirens, press and hold the front panel button for 3 seconds.