D861B Series 4K Ultra HD 8 or 16 Channel Digital Video Recorder
1 / 2Quick Setup GuidePhysical setup of the recorder and essential system settingsD861B Series Package Contents4K Ultra HD Security DVR
Back panels shown below are for illustration only. Your recorder’s back panel may appear different, with all the same ports in different locations.STEP 1: Connect cameras*Test your cameras prior to selecting a permanent mounting location by temporarily connecting the cameras and cables to your DVR.NOTES: · The extension cable must be a single stretch of cable between the recorder and camera. You cannot connectmultiple extension cables to each other. · This guide covers connecting cameras to your security recorder only. For full instructions on installing yourcameras, please refer to your camera’s documentation at lorex.com. · Before selecting a permanent mounting location for your cameras, see Ensuring Accurate Person and VehicleDetection below for important camera installation notes.STEP 2: Connect router*Connect the recorder to your router using the included Ethernet cable.NOTE: To receive automatic firmware updates and enable remote viewing with mobile apps, a high speed Internet connection is required (minimum upload speed of 5Mbps required for 4K viewing; 3.5Mbps for lower resolutions). All other system features can be used without an Internet connection.STEP 3: Connect mouseConnect the included mouse to a USB port on the recorder.
Power Adapter
Ethernet Cable
Dimensions12.8″ / 324mm
USB Mouse
HDMI Cable
2.4″ 60mm
9.8″ / 249mm
Setting Up Your RecorderSee the steps below (expanded instructions to the right) to complete initial setup of the recorder:
STEP 1:Connect cameras*
STEP 2:Connect router*
STEP 3:Connect mouse
STEP 6:Lorex Setup Wizard
STEP 4:Connect monitor*
STEP 5:Connect power
8-channel configuration shown. 16-channel will have the respective number of video inputs. For camera compatibility information, visit lorex.com/compatibility.* Not included / sold separately.
Overview of extra ports:
Audio In/OutConnect microphone / speaker*
RS485Connect Pan-Tilt-Zoom (PTZ) cameras*
NOTE: For full instructions on using the extra ports, please refer to your security recorder’s instruction manual at lorex.com.
STEP 4: Connect monitor*Connect the recorder to a monitor using the included HDMI cable or a VGA cable (not included). The HDMI port supports up to 4K resolution, and VGA supports up to 1080p.ORIMPORTANT: The system will automatically match the resolution of the connected monitor the first time you use the recorder. If you need to switch monitors, make sure you set the recorder to an output resolution supported by the new monitor before switching. See Changing the Recorder’s Output Resolution on the rear for details.STEP 5: Connect powerUse the included power adapter to connect the recorder to a nearby outlet. Turn the recorder on using the power switch on the back panel.STEP 6: Lorex Setup WizardWhen you first power up your recorder, the Lorex Setup Wizard will begin. The Wizard will help you configure core system settings. You will also create a secure password. For future reference, it is recommended that you record your password here:Record your password below and store in a secure place:
Need Help?Visit us online for up-to-date software and complete instruction manuals.
1
Visit lorex.com
2
Search for the model number of your product
3
Click on your product in the search results
4 Click on the Downloads tab
Copyright © 2020 Lorex Corporation As our products are subject to continuous improvement, Lorex reserves the right to modify product design, specificationsand prices, without notice and without incurring any obligation. E&OE. All rights reserved.D861B_QSG_EN_R1D861B_QSG_EN_R1.indd 1
Ensuring Accurate Person and Vehicle DetectionThe following are important camera installation notes to ensure accurate person and vehicle detection. For full camera mounting instructions, see your camera’s documentation at lorex.com. · Angle the camera so that objects of interest appear in the bottom of the camera image. · Choose a location where objects of interest will be no further than 50ft (~15m) from the camera.Lower accuracy for objects further away than 50ft (~15m) and/or in the top of the image.
Optimal accuracy for objects within 50ft (~15m) and in the bottom of the image.
Level position (i.e., ceiling)
· Angle the camera between 30~60° down from the level position. · Install the camera between 8-16ft (2.5-5m) off of the ground.
NOTE: Accuracy of person and vehicle detection will be influenced by multiple factors, such as the object’s distance from the camera, the size of the object, and the height and angle of the camera. Night vision will also impact the accuracy of detection.Additional Installation Tips: · Point the camera where there is the least amount of obstructions (e.g., tree branches). · Install the camera where vandals cannot easily reach. · Secure cabling so that it is not exposed or easily cut. · This camera is rated for outdoor use. Installation in a sheltered location is recommended.
Optimal angle range
2020-04-15 3:13:39 PM
Once you have completed all steps for initial setup on the front of this guide, please refer to the following sections to learn more about using your system.
Using the Mouse
· During split-screen display mode: Click an individual channel to view it in full-screen. Click again to return to the split-screen display mode.· While navigating menus: Click to open a menu option.
· During live view: Click anywhere on the screen to open the Quick Menu.· While navigating menus: Click to exit menus.
During live view: Use the scroll wheel to zoom in / out.
NOTE: In live view, hover the mouse cursor over the top of the screen to open the Navigation Bar. Move the mouse cursor away from the top of the screen to close the Navigation Bar.
Quick Access to System InformationTo quickly open a window that displays vital system information such as device ID, model number, firmware version, and IP address:· Tap the button on the front panel of the recorder.OR· Right-click to open the Quick Menu and click Info.
Using the Quick Menu
a
Right-click anywhere on the live viewing screen to open the
b
Quick Menu.
c
a. Open Main Menu.
b. Search and playback recordings.
d
c. Control PTZ cameras (not included).
d. Select camera / live display view.
e
e. View previous / next channel(s).
f. View system information.
f
g. Start/stop sequence mode.
g
h. Temporarily disable all current audible warnings.
h
i. Open manual recording controls.
i j
j. Adjust camera color and image settings.
Changing the Recorder’s Output ResolutionThe system will automatically match the resolution of the connected monitor the first time you use the recorder.IMPORTANT: If you need to switch the monitor, make sure you set the recorder to an output resolution supported by the new monitor before switching.To change the recorder’s output resolution:1. From live view, right-click and then click Main Menu. If prompted, log in using the system user name (default: admin) and your new, secure password.2. Click DISPLAY, then configure the following:
a. Set Resolution to match the highest resolution supported by your monitor. For example, select 3840×2160 for 4K monitors, or 1920×1080 for 1080p.
b. Click Apply. The recorder will
restart before changes take
effect.
a
b
PlaybackSearch through and play video recordings from the hard drive.To search for and play recordings: 1. From live view, right-click and then click Playback. If prompted, log in using the system user name (default:admin) and your new, secure password. 2. Configure the following:
a. Use the calendar on the right to select the date to playback.
b. Check channels you want to
a
play back. Click the icon beside
each selected channel to select
Mainstream (M) or Substream (S)
b
video quality.
c. Click inside the video bar to select
the playback time. Playback starts
immediately at the selected time.
d
e
cTo filter for person and vehicle recordings:PREREQUISITE: You must enable Smart Motion Detection on any and all channels you would like to filter for person and vehicle detection. See the section Motion & Smart Motion Detection for details.
d. Click to stop current playback.
e. Hover over the icon. Check Person and Vehicle to filter available playback events. Wait a few seconds for the video bar to show detection events.
Backup
Back up recordings from the hard drive to a USB flash drive (not included). To back up recordings: 1. Insert a formatted USB flash drive (not included) into a free USB port on the recorder.
2. From live view, right-click and then click Main Menu. If prompted, log in using the system user name (default: admin) and your new, secure password.
3. Click BACKUP.
4. Configure the following:
a. Select your USB drive and the
folder for the backup.
a
b. Select the channel(s) and recording types to search by.
b
c. Select a start and end time.
c
d. Choose a file format.
d
e
e. Click Search to see recordings
that match your search.
f
f. Check boxes next to recordings
you want to back up.
g
g. Click Backup.
D861B_QSG_EN_R1.indd 2
Motion, Smart Motion, & Face DetectionSet motion and face detection preferences. This section includes setup of person and vehicle detection.To configure motion: 1. From live view, right-click and then click Main Menu. If prompted, log in using the system user name (default:admin) and your new, secure password. 2. Click EVENTS. Click Events Settings on the far-left, then click the Motion Detect tab. 3. Configure the following:
a
c
b
d
e
f g
a. Select the channel you would like to configure. b. Click Enable.c. Click Setup next to Area to set an active area for motion detection. See Figure 1 below for details.d. Click Setup next to Schedule to set the weekly schedule for motion detection. See Figure 2 below for details.
e. Set preferences for how the system reacts to motion detection events.f. Click Smart Motion Detection to enable person and vehicle detection. See Figure 3 below for details.g. Click Apply to save changes.
Figure 1: Motion Detection Area
· The camera image appears with a red grid overlay. This means the entire image is enabled for motion detection.· Click or click-and-drag to add / remove boxes from the active area. Cells that have been removed from the active area appear green.· Hover near the top of the image to reveal zone selection. You can set up to 3 different zones with different sensitivity and threshold values.· Right-click when finished.
Figure 2: Motion Schedule· The default schedule, shown in Figure 2, is active at all times.· Click Modify to change the schedule for the corresponding day of the week.· Click OK when finished.
Figure 3: Smart Motion Detection· Click Enable to allow detection of people and vehicles on the selected channel.· Select a Sensitivity level (a high sensitivity value will detect smaller objects than a low value).· Check Person and/or Vehicle.· Click OK when finished.
To configure face detection:1. Click Face Settings on the far-left, then click the Face Detection tab.2. Configure the following:a. Select the channel you would like to configure.b. Face Detection is disabled by default. Click Enable. IMPORTANT: Face Detection is only available up to two channels. You must disable smart motion detection on all channels to enable Face Detection.c. Press Select to set the desired area for face detection.
a
b
c
NOTE: For more information on configuring your Face Database and Face recognition set-up, refer to the DVR’s manual at lorex.com.
Configuring Deterrence SettingsSet preferences for automatic warning light triggering on compatible Lorex deterrence cameras. For a complete list of compatible deterrence cameras, navigate to your recorder series at lorex.com/compatibility.To configure deterrence settings: 1. In live view, right-click and click Main Menu. If prompted, log in using the system user name (default: admin) andyour new, secure password.2. Click EVENTS. Click Event Settings on the far-left, then click the Deterrence tab.3. Configure the following:
a
d
b
e
c
a. Select the channel of a connected deterrence camera.b. Check Enable.c. Click Setup next to Warning Light to configure preferences.d. Click Setup next to Area to set an
factive area for automatic deterrence. See Figure 4 below for details. e. Click Setup next to Schedule to set the weekly schedule for automatic deterrence. See Figure 5 below for details. f. Click Apply.
Figure 4: Deterrence Area· The camera image appears with a grid overlay. The green area is the active area for deterrence.· Click or click-and-drag to add / remove boxes from the active area.· In Figure 4, only motion around the doorway will trigger warning light.· Right-click when finished.
Figure 5: Deterrence Schedule· The default schedule, shown in Figure 5, is active during the night, between 5pm and 7am.· Click Modify to change the schedule for the corresponding day of the week.· Click OK when finished.
To set off all connected deterrence cameras’ warning lights and sirens, press and hold the front panel button for 3 seconds.
D861B_QSG_EN_R1
report this ad2020-04-15 3:14:10 PM
References
[xyz-ips snippet=”download-snippet”]