LumenSafe Wi-Fi Video Retrieval
WARNING
Risk of Fire, Electrical Shock, Cuts or other Casualty Hazards- Installation and maintenance of this product must be performed by a qualified electrician. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and hazards involved.
Risk of Fire and Electric Shock– Make certain power is OFF before starting installation or attempting any maintenance. Disconnect power at fuse or circuit breaker.
Risk of Fire– Refer to product label for specific minimum supply conductor requirements.
Risk of Burn– Disconnect power and allow fixture to cool before handling or servicing.
Risk of Personal Injury– Fixture may become damaged and/or unstable if not installed properly.
Failure to comply with these instructions may result in death, serious bodily injury and property damage.
DISCLAIMER OF LIABILITY: Cooper Lighting Solutions assumes no liability for damages or losses of any kind that may arise from the improper, careless, or negligent installation, handling or use of this product.
NOTICE: Green ground wire provided in proper location. Do not relocate. ATTENTION Receiving Department: Note actual fixture description of any shortage or noticeable damage on delivery receipt. File claim for common carrier (LTL) directly with carrier. Claims for concealed damage must be filed within 15 days of delivery. All damaged material, complete with original packing must be retained.
Safety: This fixture must be wired in accordance with the National Electrical Code and applicable local codes and ordinances. Proper grounding is required to insure personal safety. Carefully observe grounding procedure under installation section.
APPLICATIONS: This lighting fixture is designed for outdoor lighting services, and should not be used in area of limited ventilation or inside high ambient temperature enclosures. It must be stored in a dry location prior to installation. Do not expose lighting fixture to rain, dust or other environmental conditions prior to installation and insertion of photo control or shorting cap (if so equipped). Best results will be obtained if installed and maintained according to the following recommendations.
REGULATORY INFORMATION
47 CFR Part 15 Regulation Class A Device
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment complies with radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.
Industry Canada
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the device.
This radio transmitter IC: 4706A-LMSWFG has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
FCC and IC Antenna Requirements Toward License Exempt Radio Transmitters (WLAN)The license-exempt WLAN radio transmitter contained in this equipment may only be operated with an antenna of a type, a maximum gain and the required antenna impedance as approved and specified below. To reduce potential radio interference to other users, choose the antenna type and it’s gain so that the equivalent isotopically radiated power (EIRP) is not more than that necessary for successful communication.
Wi-Fi Antenna Requirements/Specs
| Category | Description |
| Frequency Range | 2.4 GHz |
| Antenna Type | Low Profile Housing PCB Antenna |
| Impedance | 50 Ohms |
| VSWR | 1.5:1 or less at resonant point |
| Peak Radiated Gain | 4 dBi |
| Radiation | Omni-directional |
| Polarization | Vertical |
| Connector | RP-SMA(M) |
INSTALLATION
Connecting to Camera Setup Procedure
Ensure operator is within 50ft from the fixture location when performing these camera video retrieval steps.
- Power on fixture.
- Look for an 8 – digit SSID (serial number format) advertised in the laptop’s or mobile device’s available Wi-Fi drop-down and select that SSID (which will be the serial number).a. This SSID is being broadcasted by your Lumensafe Fixture.
- Enter the password to the SSID as “<serial-number>Lumen”
- Verify the Wi-Fi connection as `connected’.
Accessing Video Feed
- Open a browser in the laptop’s or mobile device and enter “192.168.13.32”.a. Use of Google Chrome web browser is recommended.
- Login into the Camera’s web client with the assigned username: (root) and password: (pass).
- In the bottom of the viewing screen, scroll right through the tabs to system, then select users. The default password specified in this instruction sheet MUST be changed here.a. Please make sure to create a very secure password.
Using Axis or other Video Management System
- Make sure the device is still connected to the SSID broadcasted by your Lumensafe Fixture (see step 1).
- Use the camera’s IP address (192.168.13.32) to pull up the video feed or stored video in the camera’s memory card using a Video Management System (VMS) of choice.a. The password created in the step above will be required.
- Stored video may be downloaded to a local device
Troubleshooting
1. For technical issues, please reach out to your agent or [email protected]
Warranties and Limitation of LiabilityPlease refer to www.cooperlighting.com for our terms and conditions.
Cooper Lighting Solutions 1121 Highway 74 South Peachtree City, GA 30269 P: 770-486-4800 www.cooperlighting.com© 2020 Cooper Lighting Solutions All Rights ReservedPublication No. IB510151EN September 16, 2020
Cooper Lighting Solutions is a registered trademark. All trademarks are property of their respective owners.Product availability, specifications, and compliances are subject to change without notice
References
[xyz-ips snippet=”download-snippet”]