Marshall CV610-U2 Full HD USB 2.0 PTZ Camera User Manual
Table of Contents
CV610-U2 Silver/BlackCV610-UB All Black Full HD USB 2.0 PTZ CameraOperating InstructionsVersion V3.6
IMPORTANT SAFETY INSTRUCTIONS:
Remove lens cover before plugging the camera into the power source.
Before starting operation, please fully read and follow all instructions in the manual. For your safety, always keep this manual with the camera for reference.
The camera power input range is 100-240VAC (50-60Hz), ensure the power supply input is within this range before powering on.
The camera power voltage is 12VDC, the rated currency is 1.5A. We suggest you use it with the original power supply adapter supplied in the box.
Please keep the power cable, video cable and control cable in a safe place. Protect all cables especially the connectors from moisture and dirt.
Operational environment: 32ºF to 122ºF ( 0ºC to 50ºC) and humidity less than 90%. To avoid any danger, do not put anything inside the camera, and keep away from corrosive liquids.
Avoid stress, vibration, and jolts during transportation, storage, and installation.
Do not detach the camera housing and cover. For any service, please contact authorized technicians.
RF cable and control cable should be individually shielded, and cannot be substituted with other cables. Do not direct the camera lens towards strong light, such as the sun or the intensive light.
Always use a dry, soft cloth to clean the camera housing. Only use neutral cleaning agents when there is need to clean smudges or dirt from the camera body. To avoid damage on the camera lens, only use a soft microfiber cloth.
Do not carry or move the camera by holding the camera head. To avoid mechanical damage of internal gears, do not rotate the camera head by hand.
Put the camera on a fixed desk or platform, avoid installing on surfaces that are not level.
Power Supply Polarity (Drawing) below:
INCLUDED IN THE BOX
Power Adapter
CV610-U2-WM – Wall Mount
Power Cable
RS232 Control Cable
USB2.0 Cable
Remote Controller (battery not included)
Main Camera
QUICK START
REMOVE Lens Cover and check all cable connections to be sure they are all firmly connected before powering on
Dial Switch Setting (at the bottom of the camera):
DIP Switch (ARM)
SW-1
SW-2
Instruction
1
OFF
OFF
Updating mode
2
ON
OFF
Debugging mode
3
OFF
ON
Undefined
4
ON
ON
Working mode
DIP Switch (IR CODE TYPE)
SW-3
SW-4
Instruction
1
OFF
OFF
Off(Close IR receiver)
2
ON
OFF
Undefined
3
OFF
ON
SEJIN 4PPM CODE
4
ON
ON
NEC CODE(standard)
DIP Switch (USB)
SW-5
SW-6
Instruction
1
OFF
OFF
Undefined
2
ON
OFF
Working mode
3
OFF
ON
Updating mode
4
ON
ON
Undefined
Note: Normal Working Mode: SW-1~5: ON, SW-6: OFF
PRODUCT HIGHLIGHTS
Compact, ergonomically designed housing perfect for small huddle rooms or locations
Supports advanced Ambarella DSP, 1/2.8 inch 5MP image sensor, and high quality 10X 62.5 degreeFOV optical lens, provides crystal clear image quality
Fast switching between different video formats: less than 1 second
10X Optical Zoom + 12X Digital Zoom
Fast and accurate focus performance
Easy firmware upgrade – (field-upgradable)
USB2.0 high-speed output
Effective RS232/485 serial control. Up to 128 presets
Compatible with the majority of videoconferencing software (UVC1.5 protocol standard)
The camera comes with an accurate IR Remote Control unit
IR transfer/IR pass function: excepts signals from other codec’s and IR remote control signals
CV610-U2 SPECIFICATIONS
Video Format
MJPG – 1080P30, 720P30, 640*480P30
Video Port
USB2.0
Sensor
1/2.8 inch high-quality 5MP CMOS sensor
Lens
F4.7-47.mm(10X), F1.8 – 14, Field of view: 62.5°(wide)-6.43°(tele)
Pankilt Rotation
Pan:±170°; Tilt:-30°-+90°, support up-side-down installation
Pan/tilt Speed
Pan: 0.1°-1207s; Tilt: 0.1°-80°/s
Preset
10 via IR remote setting, 128 via VISCA control, preset accuracy:0.1°
Control Port
RS232, RS485, USB2.0
Min. Lux
0.01Iux
White Balance
Auto/Manual
Focus
Auto/Manual
Iris
Auto/Manual
Shutter
Auto/Manual
WDR
Supported
BLC
Supported
2D Noise Reduction
Supported
3D Noise Reduction
Supported
Input Voltage
DC12V
Dimension
148mmx132mmx161mm
Net weight
0.9KG (2LBS)
RESOLUTION & FRAME RATE SETTINGS
The Marshall CV610-U2 acts as a UVC command slave to Teleconference, U.C. or Video Capture Software programs that use it as a USB capture device. Once selected as an available camera, these software platforms send commands to the camera as to compatible resolutions and frame rates based on bandwidth, software parameters, and/or computer capabilities. Some software platforms allow for direct adjust commands to change resolution and frame rates, such as VLC Player and others. CV610-U2 adjusts as commanded by the software platform or to the nearest resolution settings available (1080p, 720p, 480p). There is no way to manually adjust resolutions and frame rates from the camera or camera OSD menu since it relies on UVC (USB video class) commands. CV610-U2 adheres to UVC1.5 protocol standards.
CAMERA INTERFACE
Camera Lens
Camera Base
IR Receiver Panel
Indicator Light
Dial Switch
Tripod Screw Hole
Installation Hole
RS232 (VISCA IN) Port
USB2.0 Port
DC12V Power Input
Power Indicator light (red)
CAMERA DIMENSIONS (mm)
IR REMOTE CONTROLLER
LED Function InstructionFOCUSPress any button and shows in red color: Current selection is to control CAM1;Press any button and shows in green color: Current selection is to control CAM2;Press any button and shows in blue color: Current selection is to control CAM3;CAM1/CAM2/CAM3:Long press(3seconds) to set camera address;Short press to select camera address to control.Focus: +/-Manual focus, only valid under manual focus mode;Zoom: +/-Control the lens zoom rate;Navigate : Up/Down/Left/RightIn normal working mode, use navigate key to control pan/tilt；Or enter the OSD menu, use navigate key to set parameters.Confirm/Home button:In normal working mode, short press to let the camera go back to the home position
Menu Button: Enter the OSD menu
Number buttonsSet Preset: Long press(3seconds) the number button to save preset;Clear Preset: +number button to clear the relative preset;Long press(3seconds) the Clear button to clear all preset;Short press 3 times to reset the lens focus;Run Preset: Short press the number button to run the relative preset.
Short press to power on or off the camera
CV610-U2 OSD MENU EXPLAINED
Once the camera is powered up and working, press the Menu button on the IR remote control to enter the OSD menu (see pic.1); once changes are made press the OSD menu button again to exit and save Modi ed parameters.
Use the navigation buttons (up/down/left/right) to choose which function to select. As picture 1 shows, once the selection is made, the selected option will change to a gray background highlight. Press the right navigation button to go to the submenu (see pic.2).
In the submenu, once again press the up/down navigation buttons to scroll and select, use the left/right navigation button to cycle through selection options parameters.
Select the last option “RETURN” and press the left navigation button to get back to the main menu or previous menu.
Press the OSD button again to exit the menu.
The following pages outline the Menu structure as it appears in OSD Menu:
Camera Set
PROTOCOL
VISCAIRELCO-P/PELCO-D
ADDRESS
1-7
BAUD RATE
2400.9600.115200
PARITY BIT
NONE
STANDBY MODE
(ON/CFF )
RETURN
Back to the main menu
FOCUS
FOCUS MODE
AUTO/MANUAL/PUSH
SENSITIVITY
LOW/MID/HIGH
D_ZOOM
OFF/ON
ZOOM SPEED
0-7
LENS INIT
OFF/5K/10K/151(1201(/EXE
DIS ZOOM RATIO
OFF/ON
RETURN
Back to the main menu
WB MODE
WB MODE
ATVVB/GAIN/TEMPISOD./FLJAWB/IDRIODR./PUSH
B GAIN
VVB MODE 0-255 (Only Valid when WB MODE set to GAIN or TEMP.)
R_GAIN
0-255 (Only Valid when WB MODE set to GAIN or TEMP.)
RETURN
Back to the main menu
EXPOSURE
EXP MODE
AUTO/MANUAUIRIS/SHUT/BRI.
SHUT TIME
Shutter time: 1/1-1/10K(Valid when EXP MODE set to MANUAL or SHUT)
IRIS
Iris value: 0-13(Valid when EXP MODE set to MANUAL or IRIS)
AGE
Gain value: 04B-15dB(Valid when EXP MODE set to MANUAL)
BRIGHT
Brightness value: 0-27 (Valid when EXP MODE set to BRI.)
SLOW SHUT
OFF/ON
FLICK
OFF/50HZ/60HZ(Valid when EXP MODE set to AUTO or IRIS)
RETURN
Back to the main menu
IMAGEENHANCE
2D NR
OFF/ON
3D NR
OFF/AUTO/ 1-4
D_VVDR
OFF/1-6
GAMMA0 -4
BACKLIGHT
OFF/ON
HIGHLIGHT
OFF/ON
RETURN
Back to the main menu
MASK
MASK SWITCH
ON/OFF
COLOR
WHITE/YELLOW/GRAY/GREENNIOLET/RED
INDEX
1-8
INDEX SWITCH
OFF/ON
ROW START
0-1919
ROW END
1-1920
LINE START
0-1079
LINE END
1-1079
RETURN
Back to the main menu
D/N MODE
D/N MODE
DAY/NIGHT/AUTO
DAY TO NIGHT
15-126
NIGHT TO DAY
5-190
SWITCH DELAY
1-60
GAIN LIMIT
2-511
RETURN
Back to the main menu
CAMERAINFO
IMAGE VER.
PC-V0.0.6 (change without notice)
IMAGE DATE
16.10.20 (change without notice)
CONTROL VER.
UC V0.1.4 (change without notice)
CONTROL DATE
17.01.07 (changes without notice)
BAUDRATE
9600
PARITY BIT
NONE
RETURN
Back to the main menu
All Button Sending Mode: long press (3seconds) the Menu+ number “3” button simultaneously, the remote will enter all button sending mode.
Similar operation for the TV control mode learning.
No.
Function
1
DTR
2
DSR
3
TXD
4
GND
5
RXD
6
A
7
IR OUT
8
B
VISCA IN &RS485 Connection
Camera VISC
RS485
1
DTR
2
DSR
3
TXD
4
GND
5
RXD
6
A(+)
TX+
7
IR OUT
8
B(-)
TX-
VISCA IN 8089 Connection
Camera VISCA IN
Windows DB-9
1
DTR
6
DSR
2
DSR
4
DTR
3
TXD
2
RXD
4
GND
5
GND
5
RXD
3
TXD
6
A(+)
7
IR OUT
8
6(-)
SERIAL PORT CONFIGURATION:
Parameter
Value
Parameter
Value
Baud rate
2400/9600/115200
Stop Bit
lbit
Start Bit
1 bit
Verify Bit
None
Date Bit
8 bit
VISCA PROTOCOL
Part 1 – Camera Return Command
Ack/Completion Message
Command Packet
Note
ACK
z0 41 FF
Returned when the command is accepted.
Completion
z0 51 FF
Returned when the command has been executed.
Error Messages
Command Packet
Note
Syntax Error
z0 60 02 FF
Returned when the command format is different or when a command with illegal command parameters is accepted
Command NotExecutable
z0 61 41 FF
Returned when a command cannot be executed due to current conditions. For example, when commands controlling the focus manually are received during autofocus.
Part 2 – Camera Control Command
Command
Formation
Command Packet
Note
AddressSet
Broadcast
88 30 01 FF
Address setting
IF_Clear
Broadcast
88 01 00 01 FF
I/F Clear
CAM_Power
On
8x 01 04 00 02 FF
Power ON/OFF
Off
8x 01 04 00 03 FF
CAM_Zoom
Stop
8x 01 04 07 00 FF
Tele(Standard)
8x 01 04 07 02 FF
Wide(Standard)
8x 01 04 07 03 FF
Tele(Variable)
8x 01 04 07 2p FF
p 0(low)-7(high)
Wide(Variable)
8x 01 04 07 3p FF
Direct
8x 01 04 47 Op Oq Or Os FF
pqrs: Zoom Position (0(wide) -0x4000(tele))
CAM_Focus
Stop
8x 01 04 08 00 FF
Far(Standard)
8x 01 04 08 02 FF
Near(Standard)
8x 01 04 08 03 FF
Direct
8x 01 04 48 Op Oa Or Os FF
pgrs: Focus Position
One Push AF
8x 01 04 18 01 FF
CAM_ZoomFocus
Direct
8x 01 04 47 Op Oq Or Os Ot Ou Ov Ow FF
pqrs: Zoom Position (0(wide)- Ox4000(tete)) tuvw: Focus Position
CAMWB
Auto
8x 01 04 35 00 FF
Indoor
8x 01 04 35 01 FF
Outdoor
8x 01 04 35 02 FF
OnePush
8x 01 04 35 03 FF
Manual
8x 01 04 35 05 FF
Outdoor Auto
8x 01 04 35 06 FF
Sodium Lamp Auto
8x 01 04 35 07 FF
Sodium Auto
8x 01 04 35 08 FF
CAM_RGaln
Reset
8x 01 04 03 00 FF
Manual Control of R Gain
Up
8x 01 04 03 02 FF
Down
8x 01 04 03 03 FF
Direct
8x 01 04 43 00 00 Op Oq FF
pq: R Gain’ (0-0xFF)
Command
Fonnation
Command Packet
Note
CAM_Bgain
Reset
8x 01 04 04 00 FF
Manual Control of B Gain
Up
8x 01 04 04 02 FF
Down
8x 01 04 04 03 FF
Direct
8x 01 04 44 00 00 Op Oq FF
pq: B Gain (0-0xFF)
CAM AE
Full Auto
8x 01 04 39 00 FF
Automatic Exposure mode
Manual
8x 01 04 39 03 FF
Manual Control mode
Bright
8x 01 04 39 OD FF
Bright mode(Manual control)
CAM Shutter
Reset
8x 01 04 OA 00 FF
Shutter Setting
Up
8x 01 04 OA 02 FF
Down
8x 01 04 OA 03 FF
Direct
8x 01 04 4A 00 00 Op Oq FF
pq: Shutter Position (0-0x15)
CAM Iris–
Reset
8x 01 04 OB 00 FF
Iris Setting
Up
8x 01 04 OB 02 FF
Down
8x 01 04 OB 03 FF
Direct
8x 01 04 4B 00 00 Op Oq FF
pq: Iris Position (0- Ox11)
CAM Gain_
Reset
8x 01 04 OC 00 FF
Gain Setting
Up
8x 01 04 OC 02 FF
Down
8x 01 04 OC 03 FF
Direct
8x 01 04 OC 00 00 Op Oq FF
pq: Gain Positon (0-0x0E)
CAM Bright
Reset
8x 01 04 OD 00 FF
Bright Setting
Up
8x 01 04 OD 02 FF
Down
8x 01 04 OD 03 FF
Direct
8x 01 04 4D 00 00 Op Oq FF
pq: Bright I Positon 0
CAM_WDR
On
8x 01 04 3D 02 FF
WDR ON/OFF
OR
8x 01 04 3D 03 FF
Direct
8x 01 04 D3 Op FF
pq: WDR Position (1-0x06)
CAM Backlight
On
8x 01 04 33 02 FF
BackLight On
OR
8x 01 04 33 03 FF
BackLight OR
CAM_Aperture
Reset
8x 01 04 02 00 FF
Aperture Control
Up
8x 01 04 02 02 FF
Down
8x 01 04 02 03 FF
Direct
8x 01 04 42 00 00 Op Oq FF
pq: Aperture Gain (0-0x04)
CAM Memory
Reset
8x 01 04 3F 00 Op FF
p: Memory Number (=0 to 127) Corresponds to 0 to 9 on the Remote Commander
Set
8x 01 04 3F 01 Op FF
Recall
8x 01 04 3F 02 Op FF
CAM_LR_Reverse
On
8x 01 04 61 02 FF
Image Flip Horizontal ON/OFF
OR
8x 01 04 61 03 FF
CAM_PictureFlip
On
8x 01 04 66 02 FF
Image Flip Vertical ON/OFF
Off
8x 01 04 66 03 FF
CAM_ColorGain
Direct
8x 01 04 49 00 00 00 Op FF
(0-0x0E)
CAM_2D Noise Reduction
Direct
8x 01 04 53 Op FF
0::OFF 1:0N
Command
Funnation
Command Packet
Note
CAM_3DNoise Reduction
Direct
8x 01 04 54 Op FF
O:OFF 1: AUTO 2-5: LEVEL
FLICK
50HZ
81 01 04 23 01 FF
60HZ
81 01 04 23 02 FF
Freeze
Freeze On
81 01 04 62 02 FF
Freeze On Immediately
Freeze Off
81 01 04 62 03 FF
Freeze OR Immediately
Preset Freeze On
81 01 04 62 22 FF
Freeze On When Running Preset
Preset Freeze OR
81 01 04 62 23 FF
Freeze OR When Running Preset
IR_Transfer
Transfer On
8x 01 06 1A 02 FF
Receive IR(remote commander) CODE from VISCA communication ON/OFF
Transfer Off
8x 01 06 lA 03 FF
Pan_tiltDrive
Up
8x 01 06 01 VV WW 03 01 FF
W: Pan Weed 0z01 (low speed) to 0x 18 (high speed)WW lilt speed Ox01 (low speed) to Ox14 (high speed)YYVY: Pan Position(TBD)ZZZZ. Tit Position(TBD)
Down
8x 01 06 01 VV VVW 03 02 FF
Left
8x 01 06 01 VV VVW 01 03 FF
Right
8x 01 06 01 VV VIM 02 03 FF
Upleft
8x 01 06 01 N/V WW 01 01 FF
Upright
8x 01 06 01 N/V WW 02 01 FF
DownLeft
8x 01 06 01 VV VVW 01 02 FF
DownRight
8x 01 06 01 VV VVW 02 02 FF
Stop
8x 01 06 01 W WW 03 03 FF
AbsolutePosition
8x 01 06 02 W WWOY OY OY OY OZ OZ OZ OZ FF
RelativePosition
8x 01 06 03 W WWOY OY OY OY OZ OZ OZ OZ FF
Home
8x 01 06 04 FF
Reset
8x 01 06 05 FF
Pan-tiltLimitSet
Set
8x 01 06 07 00 OWOY OY OY OY OZ OZ OZ OZ FF
W.1 UpRight 0:DownLeft‘YYVY: Pan Limit Position(TBD)ZZZZ. Tilt Limit Position(TBD)
Clear
8x 01 06 07 01 OW07 OF OF OF 07 OF OF OF FF
Part 3 – Inquiry Command
Command
Command Packet
Return Packet
Note
CAM_Powering
8x 09 04 00 FF
y0 50 02 FF
On
y0 50 03 FF
Off(Standby)
CAM_ZoomPosing
8x 09 04 47 FF
y0 50 Op Oq Or Os FF
pgrs: Zoom Position
CAM_FocusModelng
8x 09 04 38 FF
y0 50 02 FFAuto Focus
y0 50 03 FF
Manual Focus
CAM_FocusPosing
8x 09 04 48 FF
y0 50 Op Oq Or Os FF
pqrs: Focus Position
CAM_WBModeIng
8x 09 04 35 FF
y0 50 00 FF
Auto
y0 50 01 FF
Indoor mode
y0 50 02 FFOutdoor mode
y0 50 03 FF
OnePush mode
y0 50 04 FF
ATW
y0 50 05 FF
Manual
CAM_RGainIng
8x 09 04 43 FF
y0 50 00 00 Op Oq FF
pq: R Gain
CAM_BGalnIng
8x 09 04 44 FF
y0 50 00 00 Op Oq FF
pq: B Gain
CAM_AEModelng
8x 09 04 39 FF
y0 50 00 FF
Full Auto
y0 50 03 FF
Manual
y0 50 OA FF
Shutter priority
y0 50 OB FF
Iris priority
y0 50 OD FF
Bright
CAM_ShutterPosIng
8x 09 04 4A FF
y0 50 00 00 Op Oq FF
pq: Shutter Position
CAM_IrisPosing
8x 09 04 4B FF
y0 50 00 00 Op Oq FF
pq: Iris Position
CAM_GainPosling
8x 09 04 4C FF
y0 50 00 00 Op Oq FF
pq: Gain Position
CAM_ BrIghtPosfing
8x 09 04 4D FF
y0 50 00 00 Op Oq FF
pq: Bright Position
CAM_ExpCompModelng
8x 09 04 3E FF
y0 50 02 FFOn
y0 50 03 FF
Off
CAM_ExpCompPosIng
8x 09 04 4E FF
y0 50 00 00 Op Oq FF
pq: ExpComp Position
CAM_Apertureing
8x 09 04 42 FF
y0 50 00 00 Op Oq FF
pq: Aperture Gain
CAM_MemoryIng
8x 09 04 3F FF
y0 5Opp FF
pp: Memory number last operated.
SYS_MenuModelng
8x 09 06 06 FF
y0 50 02 FF
On
y0 50 03 FF
Off
CAM_LR_ReverseIng
8x 09 04 61 FF
y0 50 02 FFOn
y0 50 03 FF
Off
CAM_PIctureFlIpIng
8x 09 04 66 FF
y0 50 02 FF
On
y0 50 03 FF
Off
CAM_IDIng
8x 09 04 22 FF
y0 50 Op Oq Or Os FF
pqrs: Camera ID
CAM_VerslonIng
8x 09 00 02 FF
y0 50 ab cdmn pq rs to vw FF
IR_Transter
8x 09 06 1A FF
y050 02 FFOn
y0 50 03 FF
Off
Pan411tMaxSpeedIng
8x 09 06 11 FF
y0 50 ww zz FF
v: PanMaxSpeecl zz: lilt Max Speed
Pan4MPosIng
8x 09 06 12 FF
y0 50 Ow Ow Ow Ow Oz Oz Oz Oz FF
%WON: PanPosition znz• Tilt Position
report this ad
Note: (x) means the camera address; (y)=(x + 8).
Pan Angle
VISCA Value
lilt Angle
VISCA Value
-170
0xF670
-30
OxFE50
-135
0xF868
0
Ox0000
-90
OxFAFO
30
Ox0 I BO
-45
OxFD78
60
0x0360
0
0x0000
90
Ox510
45
Ox0288
90
0x0510
135
Ox0798
170
0x0990
Pan(deqree/second)
lilt(decree/second)
0
0.3
0
3
1
1
1
1
2
2.
2
2.
3
2.
3
2.
4
2.
4
4.
5
3.
5
5.
6
3.
6
6
7
3.0
7
8
8
3.
8
10
9
3.
9
12
10
4.
10
15
11
5.
11
18
12
6
12
23
13
9
13
30
14
15
14
39
15
19
15
48
16
25
16
59
17
32
17
69
18
38
18
80
19
45
20
58
21
75
22
88
23
105
24
120
Shutterspeed
60/30mode
50/25mode
Iris
21
1/10000
1/10000
0
close
20
1/6000
1/6000
1
F14
19
1/4000
1/3500
2
F11
18
1/3000
1/2500
3
F0,10.
17
1/2000
1/1750
4
F8
16
1/1500
1/1250
5
F0,7.
15
1/1000
1/1000
6
F0,6.
14
1/725
1/600
7
F0,5.
13
1/500
1/425
8
F4
12
1/350
1/300
9
F0,3.
11
1/250
1/215
10
F0,3.
10
1/180
1/150
11
F0,2.
9
1/125
1/120
12
F2
8
1/100
1/100
13
F0,2.
7
1/90
1/75
6
1/60
1/50
5
1/30
1/25
4
1/15
1/12
3
1/8
1/6
2
1/4
1/3
1
1/2
1/2
0
1/1
1/1
Gain
0
0dB
Gain
8
16dB
1
2dB
9
18dB
2
4dB
10
20dB
3
6dB
11
22dB
4
8dB
12
24dB
5
10dB
13
26dB
6
12dB
14
28dB
7
14dB
15
30dB
IR TRANSFER (IR PASS)
Currently the camera support NEC code format. For customization with other codes, please contact us.
Once the camera finish power configuration, enable the IR transfer function via sending COM command.
Get the targeted remote controller point to the camera IR receiver, press keys on the remote controller. then the camera will output the received IR code via the VISCA IN port.
IR Transfer output format: XX XX XX XX FF
XX XX XX XX: Remote Controller Code
FF: End Code
The camera can save all settings, no need to re-set after the power circle.
UVC CONTROL
Control Requests
Control Selector
1
Brightness Control
PU_BRIGHTNESS_CONTROL
2
Contrast Control
PU_CONTRAST_CONTROL
3
Hue Control
PU_HUE_CONTROL
4
Saturation Control
PU_SATURATION_CONTROL
5
Sharpness Control
PU_SHARPNESS_CONTROL
6
Gamma Control
PU_GAMMA_CONTROL
7
White Balance Temperature Control
PU_WHITE_BALANCE_TEMPERATURE_CONTROL
8
Gain Control
PU_GAIN_CONTROL
9
Power Line Frequency Control
PU_POWER_LINE_FREQUENCY_CONTROL
10
Zoom (Absolute) Control
CT_ZOOM_ABSOLUTE_CONTROL
11
Zoom (Relative) Control
CT_ZOOM_RELATIVE_CONTROL
12
PanTilt (Absolute) Control
CT_PANTILT_ABSOLUTE_CONTROL
13
PanTilt (Relative) Control
CT_PANTILT_RELATIVE_CONTROL
Wall Mount Installation
Secure the CV610-U2-WM to the wall with 4 M4 screws (included).
Disconnect all cables from the camera. Align the CV610-U2 camera’s ¼-20UNC tripod screw hole with the wall mount screw hole. Use the ¼-20UNC screw (included) to secure the camera onto the wall mount. Reconnect the cables after mounting the camera.Note: Do not mount the camera upside down, as the image will be displayed upside down.
CV610-U2 Silver/BlackCV610-UB All Black Full HD USB 2.0 PTZ CameraOperating InstructionsVersion V3.6
IMPORTANT SAFETY INSTRUCTIONS:
IMPORTANT SAFETY INSTRUCTIONS:
Dial Switch Setting (at the bottom of the camera):
Menu button on the IR remote control to enter the OSD menu (see pic.1); once changes are made press the OSD menu button again to exit and save Modi ed parameters. 
report this ad
