MateStar MAT-1572R 16 Inch Stand Fan Instruction Manual

MODEL: MAT-1572R16 INCH STAND FAN INSTRUCTION MANUAL

PLEASE READ THIS USER’S MANUAL THOROUGHLY BEFORE USING

I. Structure Diagram

II. Installing and Using

First step: Assemble and connect the base with assembly up-down tube and support tubeOpen the casing and take out the base. Then assemble the tube and cover of the up-down tube and support tube. Aim the four holes on the bottom of the support tube at the holes on the base and tighten the screws. Slip decorative cover to base alongside the tube of the support tube and adjust the up-down tube to the proper height. Then rotate tighten the external joint.Second step: Assemble fan blade

1. Assemble guard cover and shroud ring Tighten back cover enclosure to the motor by fixing nuts. (Pay attention to the direction of rotation). Place joint of shroud ring downwards and cover the deep groove of shroud ring to the circle side ring of the back cover enclosure. Then tighten the bolts at the position of joint properly by nut driver.
2. Install fan blade Before installing the fan blade, take out plastic bushing for protecting the motor. While installing the fan blade, please wedge the groove on the back of the fan blade on the spacer pin of the motor. Then tighten the fixing nut of the fan blade in the left direction.
3. Assemble front cover When installing the front cover, please place the decorative ring (Trademark) of the front cover in the proper position. Then insert the circle side ring of the front cover into the fleet grace of shroud ring, which has been fixed to the back cover. Finally, screw into bolts on the joint of the shroud ring with a screwdriver.

III. Direction of Use

1. The setting of wind direction This fan can swing in up and down directions. The angle of facing upwards and downwards can be adjusted by slightly lifting or press the cover.
2. The setting of Swing Press the turning button and the fan starts to turn. Then press it again and the fan will stop turning
3. The setting of wind speed and wind type Pressing button of wind speed can adjust the speed of wind Rotating button of wind type can change the type of wind
4. Setting of timing This fan can work under 0.5h. 1h,2h, and 4h (Maximum 7.5h) by timing.

 IV. The solution to Simple Failure

When starting the fan, the fan blade doesn’t work Please check whether the power plug has really been inserted into the socket or the cover has distorted, which has touched the fan blade. If sound the noise when starting the fan, please check the unit as follows:

1. Fan blade has been right installed into the axes of the motor.
2. Groove on the back of the cover has matched the inserting groove on the axes
3. There are tiny defective edge ring existing around the fan blade.
4. The cover has distorted, which has touched the fan blade.

V. Maintaining and Storing

Be sure to switch off the power supply and pull out the plug before cleaning.

1. This machine only needs common external cleaning and wiping.
2. Place into casing and store in the dry position.

VII. Safety Instruction: 

1. Never put your finger or something into the cover to avoid any hurt.
2. Make sure to keep the fan far away from humidity, chemical articles, and oil.
3. While cleaning, be sure to splash water and do not use oil, alcohol, or chemical articles as they may cause distortion of the fan body.
4. Do not pull out the power supply plug by taking the power supply cord, which may lead to electrical shock or generating an electrical spark.
5. Keep away from curtain, clothing, or other something that may affect the fan’s working
6. Turn off all switches and pull out the power supply plug when you go out for a long time.
7. Never use the fan before finishing assembly to avoid any hurts.

report this ad

Attention:

• If the supply cord is damaged, it must be repaired by the manufacture or its service agent or a similarly qualified in order to avoid a hazard.
• Before sending for maintenance, if the unit doesn’t work please check the plug of the power supply has been inserted into the socket with electricity.

VIII. Technical Parameters

PLEASE FILL IN YOUR DETAILS FOR FUTURE USE