Mattress Pool Big Swim Ring Golden Swan Instruction Manual

Mattress Pool Big Swim Ring Golden Swan

General instructions

Assemble and Inflating Instructions

1. Open the package of the inflatable carefully and without any sharp objects.
2. Get the product out of the package and out of the polybag.
3. Check the product on damages.
4. Locate a clean area free of stones or other sharp objects.
5. Make sure the product is fully inflated before use. Make sure the product is firm to the touch but not hard. If there is any straining at the seams, the product is over-inflated. If any seams begin to strain, immediately stop the inflation and release air to reduce the pressure until signs of stress on the seam are gone. The product has to be inflated until there are some small visible folds or winkles around the seam. CAUTION: To prevent bursting, do not over inflate, use high pressure air compressor or exceed the recommended design working pressure. Fill with cold air only.
6. Close and recess the inflation valve securely.
7. Ensure that adequate air pressure is maintained in the product during use. Verify the pressure frequently, especially on very hot or cold days, using the air pressure checking method described in the instructions

Maintenance

1. Check seams and valves regularly for tears.
2. Clean the device after each use with a garden hose and air dry thoroughly before storage.
3. If this product is used in an indoor swimming pool, ensure that there is sufficient headroom

Storage

1. Ensure the device is thoroughly clean and dry first, see maintenance section.
2. Open all air valves and deflate the device completely.
3. Remove all accessories if applicable.
4. Fold the device loosely and avoid sharp bends, corners and creases which can damage the device. Replace all inflation valves caps.
5. Store in a dry place and indoors.

Repair

The device comes with a repair patch. If you have an idea where the leak is, use a mix of dishwashing liquid and water in a spray bottle, and spray over the suspicious area. Any leak will produce bubbles that will pinpoint the location of the leak.Thoroughly clean the area surrounding the leak to remove any dirt or grime.Cut a piece of repair patch large enough to overlap the damaged area by approximately 1.5 cm (1/2”). Round off the edges, and place the patch on the damaged area and press down firmly. You may want to use a weight on top to keep it in place.Do not inflate in one hour after patching.If the patch does not hold, you can purchase silicon or polyurethane based glue for repairing camping mats, tents or shoes from your local shop or market to patch the device; please refer to the instruction of the glue for patching.

Please save this instruction.

Not following these guidelines may result in drowning or other serious injury. The Product warnings, instructions, and safety rules provided with the product represent Some common risks of using water recreating devices and do not cover all instances of Risks and/or danger.

*For a full and complete description of each safety information symbol and safety sign printed on the product and the packaging please refer to the definition section or sheet.

WARNING uneven distribution of persons or load: uneven distribution of persons or loads may be dangerous. Uneven distribution of persons or loads may lead to more risks and/ or danger. Follow the warnings to avoid drowning or other serious injury. These do not cover all instances of risks and/or danger.

SAFETY INFORMATION

WARNING:

• No protection against drowning. Swimmers only.
• This is not a life saving device.
• Never allow diving or jumping onto or from this product.
• Never leave in or near the water when not in use.
• Never use in high wind, rapid currents, open water or dangerous tides.
• Do not exceed the maximum recommended weight capacity.
• Distribute the weight of person(s) and/or load evenly.
• Do not use the device if you suspect a puncture or leak.
• Not to be used while consuming or under the influence of alcohol or drugs.
• Not for white water rafting or any other extreme sports activities.
• Never use when tired or fatigued.
• Use only in water away from debris and obstructions.Design working pressure: 0.03 bar.

Manufacturer:The Essentials B.V.Rietveldenweg 40, 5222 AR, ‘s-Hertogenbosch, North Brabant, The Netherlands.

Importer:The Essentials B.V.Rietveldenweg 40, 5222 AR, ‘s-Hertogenbosch, North Brabant, The

Netherlands.EN ISO 25649-1:2017EN ISO 25649-2:2017EN ISO 25649-4:2017

Definitions

SYMBOLS	MEANINGS
	Warning action
	No protection against drowning
	Risk of getting entrapped if size is not appropriate
	Design working pressure of 0.03 bar
	Mandatory action
	Swimmers only
	Read instructions first
	Numbers of users, adults, children
	Always supervise children in water
	Max. Load capacity
	Only use within 10 meters of the shore
	Avoid entrapment, ensure loose fit
	Size designation, interior size
	Prohibition
	Do not use in offshore wind
	Do not use in offshore current
	Not for children 6 years of age and below
	Do not use in white water
	Fully inflate all air chambers

WARNING:This is not a live saving deceive. Do not leave child unattended near water Or while device is in use. Keep child within arm’s reach at all times. Keep Away from fire. Never allow diving into this product. Never leave in or Near the water when not in use. Follow these rules to avoid drowning, Paralysis or other serious injury. Warning! Only to be used in water in Which the child is within its depth and under adult supervision.

Manufacturer:The Essentials B.V.Rietveldenweg 40, 5222 AR, ‘s-Hertogenbosch, North Brabant, The Netherlands.

Importer:The Essentials B.V.Rietveldenweg 40, 5222 AR, ‘s-Hertogenbosch, North Brabant, The Netherland