COMPLETE ALL 4 STEPS. REMEMBER TO PLUG IN ONE POWER CABLE AND ONE AUDIO CABLE
STEP 1
GETTING STARTED
PACKAGE CONTENTS:
CONNECT OVERVIEW:
POWER ON
Ensure the micro-USB power cable is plugged into the micro-USB POWER port of the Connect.
Plug the USB end of the cable into an AC adapter, TV, or computer USB port.
Slide the ON/OFF switch to the ON position.
Proceed to STEP 2
STEP 2
PAIR WITH BLUETOOTH HEADPHONES
Put your Bluetooth headphones in pairing mode.Consult the user manual of your Bluetooth headphones if you are not sure how to put them in pairing mode
Once the headphones are in pairing mode, click Pairing button “A” once to put the Connect in pairing mode.Blinking blue light will change to solid blue light once successfully paired.
If you need to pair a second Bluetooth headphone, see below. Otherwise, proceed to STEP 3
OPTIONAL: PAIR WITH 2ND BLUETOOTH HEADPHONES
A second set of Bluetooth headphones can be paired after one is already connected.
Put the second headphone in pairing mode.Consult the user manual of your Bluetooth headphones if you are not sure how to put them in pairing mode
Once the headphones are in pairing mode, click Pairing button “B” once to put the Connect in pairing mode.Blinking blue light will change to solid blue light once successfully paired.
Proceed to STEP 3
STEP 3
Choose ONLY ONE audio cable supported by your TV
CHOICE A: OPTICAL
Remove protective caps from both ends of the digital optical S/PDIF audio cable
Plug digital optical S/PDIF audio cable into the OPTICAL audio input of the Connect.
Plug the other end into the TV’s DIGITAL AUDIO OUT (OPTICAL) port.
Test for sound. Make sure the volume on both your TV and headphones is turned up.
Proceed to STEP 4
NO SOUND? CHECK YOUR TV SETTINGS.
Change Sound Output to “Optical”**
Change Digital Audio Output Format to “STEREO” or “PCM”**†This may also need to done in the audio output settings menu(s) of your streaming app(s) and/or device(s) such as Apple TV®**Exact menu and item names may vary between TVs.†On some TVs settings may be located in “Advanced settings” or “Expert settings” submenus.
Proceed to STEP 4
OR
CHOICE B: 3.5 MM
Plug 3.5 mm audio cable into the 3.5 mm audio input of the Connect.
Plug the other end into the TV’s headphone jack.Headphone jack may be located on rear, side, front, or bottom of TV.
Test for sound. Make sure the volume on both your TV and headphones is turned up.
Proceed to STEP 4
OR
CHOICE C: RCA
Plug red/white ends of RCA audio cable into the TV’s red/white RCA AUDIO OUT port.
Plug 3.5 mm end of RCA audio cable into the 3.5 mm audio input of the Connect.RCA jacks on TV must be designated an AUDIO OUT. RCA input jacks, commonly labeled AV IN, INPUT, or COMPONENT will not work.
Test for sound. Make sure the volume on both your TV and headphones is turned up.
Proceed to STEP 4
NO SOUND? CHECK YOUR TV SETTINGS.
Change audio output settings to “VARIABLE”.
Set TV’s internal speakers to “OFF”.**Exact menu and item names may vary between TVs.
Proceed to STEP 4
STEP 4
ADJUSTING VOLUME
Maximize the volume level on your TV, then use volume controls on headphones to adjust to preferred volume.
If you are using the Optical cable, you may mute the TV speakers, which allows you to directly control the volume on your Bluetooth headphones.
WHEN FINISHED, power off headphones until next use
Do not put the Connect or your headphones into pairing mode.
A solid blue light on the Connect will indicate that a connection has been re-established.
ADDITIONAL INFORMATION
FACTORY RESET/CLEAR MEMORY
To perform a factory reset of the Connect, hold Pairing button “A” for approximately 5 seconds until the blue indicator light stops blinking.
All previously paired devices will be cleared from memory and a new pairing will need to be created by following the procedure in STEP 2
LED INDICATOR LIGHTS
The status of the Connect is shown by a green power / charging indicator light on the rear of the unit and two blue indicator lights on the top as follows:
INDICATOR LIGHT (S)
CONNECT STATUS
USB Power plugged in,green power indicator light solid
Battery full
USB Power plugged in,green power indicatorlight pulsing slowly
Charging
USB Power not plugged in,green power indicator light solid
Powered on
USB Power not plugged in,green power indicatorlight blinking rapidly
Low battery
Blue light blinking
Pairing mode active
One solid blue light
One Bluetooth device is connected
Two solid blue lights
Two Bluetoothdevices are connected
SAFETY AND CARE
Battery performance will be severely decreased when stored in extreme temperatures: below -10°C/14°F or above 45°C/113°F including direct sunlight.
The lifetime of the battery will be significantly reduced if your device is not charged for a long time. It is recommended to charge your device at least once a month.
Clean with a soft, slightly damp cloth. Do not use chemical cleaners.
There are no user replaceable/reparable parts in this device. Disassembling it will void your warranty.
WARNINGS
This device is designed and manufactured to operate within its defined design limits. Misuse may result in electric shock or fire. Read and follow these instructions carefully.
To prevent fire or shock hazards, do not expose this unit to rain or moisture. If the device comes in contact with liquids, quickly wipe away. If submersed in water, do not turn the device on until completely dried. Note: liquid submersion voids the warranty.
Danger of explosion or fire if batteries are damaged. Keep away from direct sunlight, naked flames, flammable gasses, or heat sources such as radiators or stoves
Only use attachments/accessories specified by the manufacturer
Changes or modifications to this unit not expressly approved by MEE audio could void the user’s authority to operate the equipment.
Keep the device and packaging out of reach of children.
WARRANTY
MEE audio products purchased from authorized resellers are covered by a 1-year manufacturer warranty. For more information, visit MEEaudio.com/support
FOR ADDITIONAL SUPPORT
VIEW OUR VIDEO SETUP GUIDE
Scan QR code or enter the URL below into your web browser:
MEEaudio.com/ConnectVid
QUESTIONS?
Get answers at MEEaudio.com/ConnectHelp
WE’RE HERE TO HELP!
Phone Support: 626-965-1008 x31Monday ~ Friday 9am to 5:00pm PST
Email Support: All emails are responded to within 2 business days
COMPLIANCE INFORMATION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC RULES
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Relocate the receiving antenna.
Increase the separation between equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
DISPOSAL AND RECYCLING
Dispose of this product in accordance with all local laws and regulations. Because this product contains electronic components and a battery, it must be disposed of separately from household waste. Contact local authorities to learn about disposal and recycling options.
MEE audio Connect AF-T1B Universal Dual Bluetooth Wireless Audio Transmitter User Manual – MEE audio Connect AF-T1B Universal Dual Bluetooth Wireless Audio Transmitter User Manual –