milwaukee M12 Pal Rotating Workshop Lamp User Manual
IMPORTANT SAFETY INSTRUCTIONS
WARNING READ AND UNDERSTAND ALL INSTRUCTIONS. When using electric appliances, basic precuautions should always be followed, including the following:
Before using the flood light, read this operator’s manual, your battery pack and charger operator’s manual, and all labels on the battery pack, charger and flood light.
- Read and understand all the instructions before using the appliance.
- To reduce the risk of injury, close supervision is necessary when an appliance is used near children.
- Store idle flood light out of reach of children. Warm flood lights can become hazardous in the hands of children.
- Do not use outdoors.
- For a rechargeable appliance – Use only the charger supplied by the manufacturer to recharge.
- Know your flood light. Read this manual carefully to learn your flood light’s applications and limitations as well as potential hazards associated with this type of tool.
- Batteries must be recharged only with the charger specified by the manufacturer. A charger that may be suitable for one type of battery may create a risk of fire when used with another battery.
- Use flood light only with specifically designated battery pack. Use of any other batteries may create a risk of fire.
- When battery pack is not in use, keep it away from metal objects like: paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Short-ing the battery terminals together may cause sparks, burns, or a fire.
- Maintain labels and nameplates. These carry important information. If unreadable or missing, contact a MILWAUKEE service facility for a replacement.
SAVE THESE INSTRUCTIONS
ADDITIONAL BATTERY SAFETY RULES
WARNING To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fluid or allow a fluid to flow inside them. Corrosive or conductive fluids, such as seawater , certain industrial chemicals, and bleach or bleach-containing products, etc., can cause a short circuit.
WARNING Do not charge non-rechargeable batteries.
SPECIFICATIONS
- Cat. No.: M12 PAL
- Volts: 12V DC
- Battery Type : M12™
- Charger Type: 12™
- USB Ouput : 5V DC
- USB Amps: 2.1ARecommended Ambient
- Operating Temperature: -17°C to 51°C
SYMBOLOGY
Volts
Direct Current
Amps
Read Operator’s Manual
Indoor use
Do not stare at the operating light source.
Class III appliance
Regulatory Compliance mark (RCM). This product meets applicable regulatory requirements.
Do not dispose of electric tools together with household waste material. Electric tools and electronic equipment that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility
LIGHT
WARNING: Recharge only with the charger specified for the battery. For specific charging instructions, read the operator’s manual supplied with your charger and battery.
Inserting/Removing Battery Pack
Insert the battery pack by sliding battery pack into the body of the tool. Insert the battery pack until the battery latches lock. To remove the battery pack, press in both battery latches and slide the battery pack off of the tool
Power
CAUTION To reduce the risk of injury, do not stare at the operating light source.
Press the power button to cycle through HIGH, LOW, and OFF settings
USB Port
To charge a phone or other electronic device using the 2.1A USB port, plug in the USB and press the USB wake button. The port will remain ON for about 2 hours.
MAINTENANCE
WARNING: To reduce the risk of injury, always unplug the charger and remove the battery pack from the charger or tool before performing any maintenance. Never disassemble the tool, battery pack or charger. Contact a MILWAUKEE® service facility for ALL repairs.
Maintain Light
Keep your light, battery pack and charger in good repair by adopting a regular maintenance program. If the light does not work properly, return the light to a MILWAUKEE® service facility for repairs
WARNING: To reduce the risk of personal injury and damage, never immerse your tool, battery pack or charger in liquid or allow a liquid to flow inside them.
Cleaning
Keep tool handles clean, dry and free of oil or grease. Use only mild soap and a damp cloth to clean the tool, battery pack and charger since certain cleaning agents and solvents are harmful to plastics and other insulated parts. Some of these include gasoline, turpentine, lacquer thinner, paint thinner, chlorinated cleaning solvents, ammonia and household detergents containing ammonia. Never use flammable or combustible solvents around tools.
WARRANTY – AUSTRALIA and NEW ZEALAND
Please refer to Australian and New Zealand warranty supplied with tool. This warranty applies only to product sold by authorised dealers in Australia and New Zealand.
SERVICE – AUSTRALIA and NEW ZEALAND
MILWAUKEE® prides itself in producing a premium quality product that is Nothing But Heavy DutyTM. Your satisfaction with our products is very important to us! If you encounter any problems with the operation of this tool, please contact your authorised MILWAUKEE® dealer.
For a list of MILWAUKEE® dealers, guarantee or service agents please contact MILWAUKEE® Customer Service or visit our website.
(Australia Toll Free Telephone Number 1300 645 928)
(New Zealand Toll Free Telephone Number 0800 645 928) or visit milwaukeetool.com.au / milwaukeetool.co.nz.
Milwaukee Electric Tool Corporation 13135 West Lisbon Road, Brookfield, Wisconsin U.S.A. 53005
Milwaukee Tool (Australia)
21 Kelletts Road, Rowville, VIC 3178Melbourne, Australia
Milwaukee Tool (New Zealand)274 Church Street, Penrose,Auckland, 1061, New Zealand
DESIGNED BY MILWAUKEE ELECTRIC TOOL CORP. PROFESSIONALLY
MADE IN CHINA PRINTED IN CHINA
[xyz-ips snippet=”download-snippet”]