MKA-32 Quick Release Bracket
For Use with all PowerDrive, Terrova, and Ulterra Trolling Motors.Kit Includes:
| Item # | QTY. | parts | Description |
| 1 | 1 | 2222716 | Spring, Compression |
| 2 | 1 | 2223205 | Stop, Draw Bar Quick Attach |
| 3 | 1 | 2223452 | Screw, 1/4 x 3/4 AB |
| 4 | 1 | 2223605 | Draw Bar Quick Attach Plate |
| 5 | 1 | 2225110 | Pad, Urethane |
| 6 | 1 | 2228412 | Cam Puck |
| 7 | 1 | 2228415 | Cam Lever |
| 8 | 1 | 2262635 | Pin Roller |
| 9 | 1 | 2371937 | Plate, Backer |
| 10 | 1 | 2371986 | Plate, Top |
| 11 | 1 | 2371996 | Plate, Base |
| 12 | 1 | 2372623 | Pin, w/Ring |
| 13 | 1 | 2372644 | Ron Pin |
| 14 | 1 | 2373428 | Screw 5/16-18 x 3/4″ |
| 15 | 1 | 2373650 | Lanyard, Plastic |
| 16 | 1 | 2770245 | Cover, Quick Release Plate |
| 1 | 2994863 | Bag Assembly, Includes: | |
| 6 | 2332104 | 1/4″ x 5/8 Screw | |
| 6 | 2223446 | Flat Head 1/4″ x 2″ Screw | |
| 6 | 2263103 | 1/4″ Lock Nut | |
| 6 | 2261713 | 1/4″Washer |
Installation Instructions:
- Remove both side covers (marked [A] in the illustration).
- Remove Pin [12] and open Cam Lever [7]. Remove the Top Plate [10] from the Base Plate [11].
- Use the (6) 1/4” x 5/8” Screws to fasten the Top Plate to the bottom of the motor base extrusion.Note: For Ulterra motors use the hex head screws and clipped washers that came with the Ulterra.
- Re-install both side covers. Assemble the motor and Top Plate onto the Base Plate and latch the Cam Lever.
- Positioning the motor/quick release bracket for mounting location:A: For PowerDrive or Terrova motors: Fully deploy the motor and position the bracket/motor on the bow of your boat to check for proper clearance (the motor, as it is lowered into the water or raised into the boat must not encounter any obstructions.)B: For Ulterra motors: Postion the bracket/motor so the notch in the base is aligned with the rub rail of the boat (for proper clearance the entire notch must be visible beyond the rub rail, as shown to the right.)
- Mark the side edges and rear of the Base Plate on the bow of your boat. Open the Cam Lever and remove the Base Plate. Reposition the Base Plate to the marks. Locate and mark the (6) mounting holes in the Base Plate and drill the holes to 9/32” diameter. Fasten Base Plate to the bow using (6) 1/4” x 2” Flat Head Screws, (6) Fender Washers, and (6) Lock Nuts.Note: Mounting surface for Base Plate must be completely flat. Washers must be used to shim the base plate flat before hardware is tightened. The top Plate will not fit correctly unless Base Plate is installed completely flat.
- Install motor/Top Plate to Base Plate and latch Cam Lever.
- Your motor is now mounted. Always check that the Cam Lever is latched always use Pin [12] to ensure the cam lever remains latched.
- Cover [16] is available to use when the motor is not mounted on the boat. To install the cover, lay the cover on top of the base plate, apply down pressure to the center of the Cover while latching the Cam Lever. The cover should fit snug to the Base Plate.
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Check out the collection of boat parts & hardware we offer.
[xyz-ips snippet=”download-snippet”]