Optix SeriesLCD MonitorOptix G273QF (3CA8)Optix G273QPF (3CA8)RevisionV1.0, 2020/12
Getting Started
This chapter provides you with information on hardware setup procedures. While connecting devices, be careful in holding the devices and use a grounded wrist strap to avoid static electricity.
Package Contents
| Monitor | Optix G273QF / Optix G273QPF |
| Documentation | Quick Start Guide |
| Registration Card | |
| Warranty Card | |
| MSI Reward Program Card | |
| Accessories | Stand with Screw(s) |
| Stand Base with Screw(s) | |
| Power Adapter & Power Cord | |
| Cables | HDMI Cable (Optional.) |
| DisplayPort Cable (Optional.) |
⚠ Important
- Contact your place of purchase or local distributor if any of the items are damaged or missing.
- Package contents may vary by country.
Installing the Monitor Stand
- Leave the monitor in its protective foam packaging. Align the stand bracket to the monitor groove.
- Tighten the stand bracket with screws.
- Connect the base to the stand and tighten the base screw to secure the base.
- Make sure the stand assembly is properly installed before setting the monitor upright.
⚠ Important
- Place the monitor on a soft, protected surface to avoid scratching the display panel.
- Do not use any sharp objects on the panel.
- The groove for installing the stand bracket can also be used for a wall mount. Please contact your dealer for a proper wall mount kit.
Optix G273QF
Optix G273QPF
Adjusting the Monitor
This monitor is designed to maximize your viewing comfort with its adjustment capabilities.
⚠ Important
- Avoid touching the display panel when adjusting the monitor.
- Please slightly tilt the monitor backward before pivoting it.
Optix G273QF
Optix G273QPF
Monitor Overview
| 1 | Power Button |
| 2 | Navi Key |
| 3 | Kensington Lock |
| 4 | DisplayPort |
| 5 | HDMI Port  |
| 6 | headphone jack |
| 7 | Power Jack |
Connecting the Monitor to PC
- Turn off your computer.
- Connect the video cable from the monitor to your computer.
- Assemble the monitor power adapter & power cord. (Figure A)
- Connect the power adapter to the monitor power jack. (Figure B)
- Plug the power cord into the electrical outlet. (Figure C)
- Turn on the monitor. (Figure D)
- Power on the computer and the monitor will auto-detect the signal source.
OSD Setup
This chapter provides you with essential information on OSD Setup.⚠ ImportantAll information is subject to change without prior notice.
The monitor comes with a Navi Key, a multi-directional control that helps navigate the On-Screen Display (OSD) menu.
Up/Down/Left/Right:
- selecting function menus and items
- adjusting function values
- entering into/exiting from function menus
Press (OK):
- launching the On-Screen Display (OSD)
- entering submenus
- confirming a selection or setting
Hot Key
- Users may enter into Game Mode, Screen Assistance, Alarm Clock, and Input Source function menus by moving the Navi Key up, down, left, or right when the OSD menu is inactive.
- Users may customize their own Hot Keys to enter into different function menus.
Gaming
| 1st Level Menu | 2nd/3rd Level Menu | Description |
| Game Mode | User | •All items can be adjusted by users.•Use the Up or Down Button to select and preview mode effects.•Press the OK button to confirm and apply your mode type. |
| FPS | ||
| Racing | ||
| RTS | ||
| RPG | ||
| Night Vision | OFF | •This function optimizes background brightness and is recommended for FPS games. |
| Normal | ||
| Strong | ||
| Strongest | ||
| A.I. | ||
| Response Time | Normal | •Users can adjust Response Time in any mode.•Response Time will be grayed out while MPRT is enabled. |
| Fast | ||
| Fastest |
| MPRT | OFF | •When MPRT is enabled, Brightness cannot be enabled and will be grayed out.•MPRT and HDCR cannot be enabled simultaneously.•Response time will be grayed out while MPRT is enabled.•MPRT has to be disabled whileAdaptive-Sync is set to ON. | |
| ON | |||
| Refresh Rate | Location | Left Top | •Users can adjust Refresh Rate in any mode.•Default Refresh Rate Location is Left Top. Location is adjustable in OSD Menu. Press the OK button to confirm and apply your Refresh Rate Location.•This monitor follows and works at the Operating System’s preset Screen Refresh Rate. |
| Right Top | |||
| Left Bottom | |||
| Right Bottom | |||
| OFF | |||
| ON | |||
| Alarm Clock | Location | Left Top | •Users can adjust the Alarm Clock in any mode.•After setting the time, press the OK button to activate the timer.•Default Alarm Clock Location is Left Top. Users can select their own location. |
| Right Top | |||
| Left Bottom | |||
| Right Bottom | |||
| Customize | |||
| OFF | |||
| 15:00 | 00:01 – | ||
| 30:00 | 99:59 | ||
| 45:00 | |||
| 60:00 | |||
| Screen Assistance | None |  |
•Users can adjust Screen Assistance in any mode.•Screen Assistance default is None. |
| Icon | |||
| Position | |||
| Reset | |||
| Adaptive-Sync | OFF |
|
|
| ON |
Professional
| 1st Level Menu | 2nd Level Menu | Description |
| Pro Mode | User | •Default mode is User.•All items can be adjusted by users.•Use Up or Down Button to select and preview mode effects.•Press the OK Button to confirm and apply your mode type. |
| Anti-Blue | ||
| Movie | ||
| Office | ||
| Low Blue Light | OFF | •Low Blue Light protects your eyes against blue light. When enabled, Low Blue Light adjusts the screen color temperature to a more yellow glow.•Users can adjust Low Blue Light in any mode.•When Pro Mode is set to Anti-Blue, it ismandatory to enable Low Blue Light. |
| ON | ||
| HDCR | OFF | •Users can adjust HDCR in any mode.•HDCR enhances image quality by increasing the contrast of images.•When HDCR is set to ON, Brightness will be grayed out.•HDCR and MPRT cannot be enabled simultaneously. |
| ON | ||
| MPRT | OFF | •When MPRT is enabled, Brightness cannot be enabled and will be grayed out.•MPRT and HDCR cannot be enabled simultaneously.•Response time will be grayed out while MPRT is enabled.•MPRT has to be disabled while Adaptive-Sync is set to ON. |
| ON | ||
| ImageEnhancement | OFF |
|
| Weak | ||
| Medium | ||
| Strong | ||
| Strongest |
Image
| 1st Level Menu | 2nd/3rd Level Menu | Description |
| Brightness | 0-100 | •Users can adjust Brightness in any mode.•Brightness will be grayed out when MPRT or HDCR are enabled. |
| Contrast | 0-100 | •Users can adjust Contrast in any mode. |
| Sharpness | 0-5 | •Users can adjust Sharpness in any mode.•Sharpness improves clarity and details of images. |
| Color Temperature | Cool | •Color Temperature default is Normal.•Use the Up or Down Button to select and preview mode effects.•Press the OK button to confirm and apply your mode type.•Users can adjust Color Temperature in Customization mode. |
| Normal | ||
| Warm | ||
| Customization | R (0-100) | |
| G (0-100) | ||
| B (0-100) | ||
| Screen Size | Auto | •Users can adjust Screen Size in any mode, any resolution, and any screen refresh rate.•Default is Auto. |
| 4:03 | ||
| 16:09 |
Input Source
| 1st Level Menu | 2nd Level Menu | Description |
| HDMI1 | ||
| HDMI2 | ||
| DP | ||
| Auto Scan | OFF |
|
| ON |
| 1st Level Menu | 2nd Level Menu | Description |
| Up / Down / Left/ Right | OFF |
|
| Brightness | ||
| Game Mode | ||
| Screen | ||
| Assistance | ||
| Alarm Clock | ||
| Input Source | ||
| Refresh Rate | ||
| Info. On-Screen |
Setting
| 1st Level Menu | 2nd Level Menu | Description |
| Language | English |
|
| Transparency | 0~5 |
|
| OSD Time Out | 5~30s |
|
| Power Button | OFF |
|
| Standby |
|
|
| Info. On-Screen | OFF |
|
| ON | ||
| HDMI CEC | OFF |
|
| ON | ||
| Reset | YES |
|
| NO |
Specifications
| Model | Optix G273QF | Optix G273QPF |
| Size | 27 inch | |
| Curvature | Flat | |
| Panel Type | Rapid IPS | |
| Resolution | 2560 x 1440 @165Hz | |
| Aspect Ratio | 16:9 | |
| Brightness (nits) | 300 (typ.) | |
| Contrast Ratio | 1000:1 | |
| Refresh Rate | 165Hz | |
| Response Time | 1ms (GTG) | |
| I/O |
|
|
| View Angles | 178°(H) , 178°(V) | |
| DCI-P3*/ sRGB | 93% / 125% | |
| Surface Treatment | Anti-glare | |
| Display Colors | 16.7M | |
| Power Adapter Specs |
|
|
| Power Input | 100~240Vac, 50~60Hz, 1.6A max | |
| Power Output | 19.0V  3.42A |
|
| Adjustment (Tilt) | -5° ~ 20° | -5° ~ 20° |
| Adjustment (Height) | 0 ~ 130mm | |
| Adjustment (Swivel) | -45° ~ 45° | |
| Adjustment (Pivot) | -90° ~ 90° | |
| Kensington Lock | Yes | |
| VESA Mounting |
|
|
| Dimension (W x H x D) | 614.93 x 444.6 x 228.38 mm | 614.93 x 535.39 x 233.68 mm |
| Weight | 4.5 Kg (net) /
7.5 Kg (gross) |
6.3 Kg (net) /
9.4 Kg (gross) |
| Environment | Operating |
|
| Storage |
|
* Based on CIE1976 test standards.
Preset Display Modes
| Standard | Resolution | HDMI | DP | |
| VGA | 640×480 | @60Hz | V | V |
| @67Hz | V | V | ||
| @72Hz | V | V | ||
| @75Hz | V | V | ||
| Dos-Mode | 720×480 | @60Hz | V | V |
| 720×576 | @50Hz | V | V | |
| SVGA | 800×600 | @56Hz | V | V |
| @60Hz | V | V | ||
| @72Hz | V | V | ||
| @75Hz | V | V | ||
| XGA | 1024×768 | @60Hz | V | V |
| @70Hz | V | V | ||
| @75Hz | V | V | ||
| SXGA | 1280×1024 | @60Hz | V | V |
| @75Hz | V | V | ||
| WXGA+ | 1440×900 | @60Hz | V | V |
| WSXGA+ | 1680×1050 | @60Hz | V | V |
| Full HD | 1920×1080 | @60Hz | V | V |
| @120Hz | V | V | ||
| @144Hz | V | X | ||
| @165Hz | X | V | ||
| QHD | 2560×1440 | @60Hz | V | V |
| @120Hz | V | V | ||
| @144Hz | V | X | ||
| @165Hz | X | V | ||
| VideoTiming Resolution | 480P | V | V | |
| 576P | V | V | ||
| 720P | V | V | ||
| 1080P WOHz | V | V | ||
| 1080P @120Hz | V | V | ||
| 2160P 030Hz | V | V | ||
| 2160P @60Hz | V | V |
Troubleshooting
The power LED is off.
- Press the monitor power button again.
- Check if the monitor power cable is properly connected.
No image.
- Check if the computer graphics card is properly installed.
- Check if the computer and monitor are connected to electrical outlets and are turned on.
- Check if the monitor signal cable is properly connected.
- The computer may be in Standby mode. Press any key to activate the monitor.
The screen image is not properly sized or centered.
- Refer to Preset Display Modes to set the computer to a setting suitable for the monitor to display.
No Plug & Play.
- Check if the monitor power cable is properly connected.
- Check if the monitor signal cable is properly connected.
- Check if the computer and graphics card are Plug & Play compatible.
The icons, font or screen are fuzzy, blurry or have color problems.
- Avoid using any video extension cables.
- Adjust brightness and contrast.
- Adjust RGB color or tune the color temperature.
- Check if the monitor signal cable is properly connected.
- Check for bent pins on the signal cable connector.
The monitor starts flickering or shows waves.
- Change the refresh rate to match the capabilities of your monitor.
- Update your graphics card drivers.
- Keep the monitor away from electrical devices that may cause electromagnetic interference (EMI).
Safety Instructions
- Read the safety instructions carefully and thoroughly.
- All cautions and warnings on the device or user’s manual should be noted.
- Refer servicing to qualified personnel only.
- Keep the User’s Guide that comes with the package for future reference.
- To prevent fire or shock hazards, keep this device away from humidity and high temperature.
- Lay this device on a reliable flat surface before setting it up.
- Make sure that the power voltage is within its safety range and has been adjusted properly to the value of 100~240V before connecting the device to the power outlet.Do not disable the protective earth pin from the plug. The device must be connected to an earthed mains socket outlet.
- Always disconnect the power cord or switch the wall socket off if the device would be left unused for a certain time to achieve zero energy consumption.
- The ventilator on the device is used for air convection and to prevent the device from overheating. Do not cover the ventilator.
- Do not leave the device in an unconditioned environment with a storage temperature above 60℃ or below -20℃, which may damage the device.
- NOTE: The maximum operating temperature is around 40℃.
- When cleaning the device, be sure to remove the power plug. Use a piece of soft cloth rather than an industrial chemical to clean the device. Never pour any liquid into the opening; that could damage the device or cause electric shock.
- Place the power cord in a way that people are unlikely to step on it. Do not place anything on the power cord.
- Always keep strong magnetic or electrical objects away from the device.
- If any of the following situations arises, get the device checked by service personnel:
- The power cord or plug is damaged.
- Liquid has penetrated into the device.
- The device has been exposed to moisture.
- The device does not work well or you can not get it to work according to the user’s manual.
- The device has dropped and been damaged.
- The device has obvious signs of breakage.
- To prevent the monitor from tipping over, secure the monitor to a desk, wall or fixed object with an anti-tip fastener that helps to properly support the monitor and keep it safe in place.
⚠ ImportantPlease confirm the power distribution system in the installation site shall provide the circuit breaker rated 120/240V, 20A (maximum).
TÜV Rheinland Certification
TÜV Rheinland Low Blue Light Certification
Blue light has been shown to cause eye fatigue and discomfort. MSI now offers monitors with TÜV Rheinland Low Blue Light certification to ensure users’ eye comfort and well-being. Please follow the instructions below to reduce the symptoms from extended exposure to the screen and blue light.
Low Blue Light ( Software Solution)
- Place the screen 20 – 28 inches (50 – 70 cm) away from your eyes and a little below eye level.
- Consciously blinking the eyes every now and then will help to reduce eye strain after extended screen time.
- Take breaks for 20 minutes every 2 hours.
- Look away from the screen and gaze at a distant object for at least 20 seconds during breaks.
- Make stretches to relieve body fatigue or pain during breaks.
- Use the Reader/Anti-Blue mode or turn on the optional Low Blue Light function.
TÜV Rheinland Flicker Free Certification
Flicker Free
- TÜV Rheinland has tested this product to ascertain whether the display produces visible and invisible flickers for the human eye and therefore strains the eyes of users.
- TÜV Rheinland has defined a catalog of tests, which sets out minimum standards at various frequency ranges. The test catalog is based on internationally applicable standards or standards common within the industry and exceeds these requirements.
- The product has been tested in the laboratory according to these criteria.
- The keyword “Flicker Free” confirms that the device has no visible and invisible flicker defined in this standard within the range of 0 – 3000 Hz under various brightness settings.
- The display will not support Flicker-Free when Anti Motion Blur/MPRT is enabled. (The availability of Anti Motion Blur/MPRT varies by-products.)
Regulatory Notices
CE Conformity
This device complies with the requirements set out in the CouncilDirective on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility (2014/30/EU), Low-voltageDirective (2014/35/EU), ErP Directive (2009/125/EC) and RoHS directive (2011/65/EU). This product has been tested and found to comply with the harmonized standards for Information Technology Equipment published under the Directives of the Official Journal of the European Union.
FCC-B Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the measures listed below:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/television technician for help.
Notice 1The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.Notice 2Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
MSI Computer Corp.901 Canada Court, City of Industry, CA 91748, USA(626) 913-0828www.msi.com
WEEE Statement
Under the European Union (“EU”) Directive on Waste Electrical andElectronic Equipment, Directive 2012/19/EU, products of “electrical and electronic equipment” cannot be discarded as municipal waste anymore and manufacturers of covered electronic equipment will be obligated to take back such products at the end of their useful life.
Chemical Substances InformationIn compliance with chemical substances regulations, such as the EU REACH Regulation (Regulation EC No. 1907/2006 of the European Parliament and the Council), MSI provides the information of chemical substances in products at:https://storage-asset.msi.com/html/popup/csr/evmtprtt_pcm.html
RoHS Statement
Japan JIS C 0950 Material DeclarationA Japanese regulatory requirement, defined by specification JIS C 0950, mandates that manufacturers provide material declarations for certain categories of electronic products offered for sale after July 1, 2006.https://storage-asset.msi.com/html/popup/csr/cemm_jp.html
India RoHSThis product complies with the “India E-waste (Management and Handling) Rule 2011” and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule.
Turkey EEE RegulationConforms to the EEE Regulations of the Republic Of Turkey.Ukraine Restriction of Hazardous SubstancesThe equipment complies with requirements of the Technical Regulation, approved by the Resolution of Cabinet of Ministry of Ukraine as of December 3, 2008, № 1057, in terms of restrictions for the use of certain dangerous substances in electrical and electronic equipment.Vietnam RoHSAs of December 1, 2012, all products manufactured by MSI comply with Circular 30/2011/TT-BCT temporarily regulating the permitted limits for a number of hazardous substances in electronic and electric products.
Green Product Features
- Reduced energy consumption during use and stand-by
- Limited use of substances harmful to the environment and health
- Easily dismantled and recycled
- Reduced use of natural resources by encouraging recycling
- Extended product lifetime through easy upgrades
- Reduced solid waste production through take-back policy
Environmental Policy
report this ad
- The product has been designed to enable proper reuse of parts and recycling and should not be thrown away at its end of life.
- Users should contact the local authorized point of collection for recycling and disposal of their end-of-life products.
- Visit the MSI website and locate a nearby distributor for further recycling information.
- Users may also reach us at for information regarding proper disposal, take-back, recycling, and disassembly of MSI products.
Warning!Overuse of screens is likely to affect eyesight.Recommendations:
- Take a 10-minute break for every 30 minutes of screen time.
- Children under 2 years of age should have no screen time. For children aged 2 years and over, screen time should be limited to less than one hour per day.
Copyright and Trademarks NoticeCopyright © Micro-Star Int’l Co., Ltd. All rights reserved. The MSI logo used is a registered trademark of Micro-Star Int’l Co., Ltd. All other marks and names mentioned may be trademarks of their respective owners. No warranty as to accuracy or completeness is expressed or implied. MSI reserves the right to make changes to this document without prior notice.Technical SupportIf a problem arises with your product and no solution can be obtained from the user’s manual, please contact your place of purchase or a local distributor. Alternatively, please visit https://www.msi.com/support/ for further guidance.
References
[xyz-ips snippet=”download-snippet”]