MZOOM MLS061 Motorcycle Universal LCD TFT Digital Speedometer 14000RPM 6 Gear Backlight Instructions

1. Operating Voltage9～18VDC
2. Speedometer1. Calculate the vehicle speed according to the received pulse signal2. Metric and British3. No pulse signal, displayed as 04. The number of backstage magnets and tire circumference can be set5. Display speed increase 5%6. When there is a speed, 1, 2, and 3 lights are displayed on the horse (Light 1 is 3 LEDs in parallel)
3. Engine speed signalLiquid crystal display, 166Hz to 10 × 1000r / min.The number of cylinders can be set in the backgroundSet to 2: 166.6Hz for 10 × 1000RPMSet to 4: 333.3Hz corresponds to 10 × 1000RPMOver-rotation headlights: the speed is 9-10 × 1000RPM, the yellow light is always onOver-rotation light: The yellow light turns off when the speed reaches 10 × 1000RPM or more, and the red light blinks at 2Hz.
4. FuelLiquid crystal display, with fuel sensor connected, fuel block display, no connection without display1. When judging whether there is a sensor, there is no sensor, and the fuel related is not displayed. If there is a sensor, it is displayed according to the corresponding resistance range.Judge the presence or absence of a sensor, a value is being judged, not just power on, it will judge3.No driving damping, the entire segment is 10 seconds, driving damping, 7 seconds per division4. The fuel level is as low as 1 block and below, the front oiler flashes5. Set 2-wire or 3-wire sensors in the background

   Piece	0 block, E, F, tankersymbol flashes	1 flash, oil potflash	1Piece	2Piece	3Piece	4Piece	SPiece
   2 lines	900 above	89-81	80-71	70-53	52-34	33-15	14 0 below
   3 lines	531 0above	530-501	500-401	400-284	283-168	167-57	50 0 below

5. Water temperature1. When judging whether there is a sensor, there is no sensor, and the water temperature is not displayed. If there is a sensor, it is displayed according to the corresponding resistance range.2. Judge the presence or absence of a sensor, a value is being judged, not just power on, it will judge3. 2 seconds data average4. The higher the temperature, the smaller the resistance value. When the resistance value is lower than the number set in the background, the LED lights up, and the LED lights up.5. When the temperature is too high, the water temperature symbol is red and flashes.
6. Key FunctionA. Press the button briefly to switch between total (ODO) and subtotal (TRIP).B. On the subtotal TRIP interface, press and hold the button for 3 seconds to clear the subtotal
7. Clock adjustmentIn the total state, long press the button for 3 seconds, the clock hour will always be red, and the second will not flash. Short press the button and add 1, long press the button(The second switches to the quantile red and is always displayed, the second does not flash, press the button shortly to increase 1, and then press the button for 3 seconds to save and exit, debug If there is no operation for 5 seconds, save and exit
8. LCD screenTFT 4.3 inch screen 480 * 272 1000 1000cd / m²
9. Oil lampPress and hold the button for 3 seconds, the light goes off, and enter the next round of counting at the same time
10. DJ621-E2.8*05DJ7031A-2.8-211. Black: Keylock (12V positive)2. Brown: Backlight +3. Blue / White: Fuel signal4. Light blue: turn right5. Red and black: Engine speed signal6. Red: battery (normal power, 12V positive)7. Blue: High beam8. Green: negative9. Orange: turn left
11. DJ621-E2.8*05DJ7031A-2.8-211. Pink: 1 file2. Blue / Red: 2 levels3. Green / Black: 3 levels4. Yellow / Red: 4 levels5. Green / Red: N files6. Yellow / White: 5 levels7. Gray: 6 levels8. Brown/red: Engine failure9. Green / White: water temperature
12. Motor oil
13. Background control buttons
14. DJ621-E2.8*05DJ7031A-2.8-211. Red / White: Sensor positive2. Green / Blue: sensor negative3. Black / White: sensor signal

Background parameter setting

Press and hold the button, ACC power on, enter the background password interface, short press plus 1, long press to shift, enter the correct password  6810, the following interface is displayed. Press briefly to cycle through the items, and press and hold to modify the displayed value. ACC power-down restart takes effect.