HPRF200BKMANUAL (p. 2)Wireless Headphones
Introduction:
The Nedis wireless headphones are the perfect solution for enjoying music in and around the house. The closed headphones ensure a great listening experience. Equipped with PLL technology for optimal reception of the signal. Auto detecting system for automatic power on or off. Integrated charging circuit for charging the batteries inside the headphone and auto-tuning for the audio signal. Suitable for use with TV, CD, PC, MP3, RADIO, etc.How to begin:Before the wireless headphones can be used the following has to be done first.
Step 1:Open the battery compartment on the *right side to insert the rechargeable batteries. Make sure the positive (+) and negative (-) poles are correctly aligned.*Note: the right side of the headphone is marked with R in the headband and also recognizable as the shell with the power button.
Step 2:Close the battery compartment after inserting the rechargeable batteries.
Step 3:Insert the antenna into the antenna socket of the transmitter.
Step 4:Connect the audio cable of the transmitter, fitted with a 3.5 mm jack plug, to the headphones (audio) output of an audio providing appliance, like TV, audio equipment, PC, etc.
Step 5:Connect the plug on the AC/DC mains adapter cable to the DC IN socket at the back of the transmitter. Then plug the adapter into a wall outlet.Note: the power LED will not light up if the receiver is not receiving an audio signal.
Step 6:Before using the headphones, the batteries need to be charged. Take the charging cable with the 2.5 mm power jack and plug it into the recharging socket of the right shell of the headphones.Note: Leave the headphones to charge for 24 hours before first use. The second and subsequent charges take about 10 hours.The red charge LED will light up indicating that charging is in progress.
Operation:
Switch on the audio-providing appliance and adjust its volume to roughly a quarter of the maximum setting. The transmitter will switch on automatically. When the audio appliance is switched off the transmitter will automatically switch off after 4~5 minutes.Note: If the volume output is too low the transmitter will switch off or switch to standby mode and the SIGNAL/POWER LED will not light up. It is not possible to charge and listen at the same time.Charging has priority.
Step 1:Switch on the headphones and the POWER LED will light up.Do not turn the volume to maximum when switching on the headphones.
Step 2:Select a channel with the channel switch at the back of the transmitter. Adjust the headphone’s reception by pressing the AUTO TUNE button at the left shell of the headphones.
Note: if the sound is poor, change to a different channel on the transmitter and press the AUTO TUNE button once more.
Note: When using the headphones at a maximum volume level, the batteries will run empty in a shorter time. It will also increase the possibility of hearing noise due to the wireless connection. Therefore it is recommended to increase the volume level of the audio providing appliance and decrease the volume level of the headphones. This will improve the performance of the wireless headphones.
Specifications:
| Transmission frequency: | 863 MHz |
| Frequency response: | 20 – 20.000Hz |
| S/N ratio: | 54 dB |
| Range: | 100 m (open area), 30 m (indoors) |
| Power supply: | 12 V DC, 200 mA |
| Batteries: | 2 x AAA, NiMH, 550 mAh (included) |
| Charging time: | ± 10hrs |
| Playing time: | ± 1 1hrs |
Safety precautions:
To reduce the risk of electric shock, this product should ONLY be opened by an authorized technician when service is required. Disconnect the product from mains and other equipment if a problem should occur. Do not expose the product to water or moisture.
Maintenance:
Clean only with a dry cloth. Do not use cleaning solvents or abrasives.
Warranty:
No guarantee or liability can be accepted for any changes and modifications of the product or damage caused due to incorrect use of this product.
General:
Designs and specifications are subject to change without notice.All logos brands and product names are trademarks or registered trademarks of their respective holders and are hereby recognized as such.Keep this manual and packaging for future reference.
Attention:
This product is marked with this symbol. It means that used electrical and electronic products should not be mixed with general household waste. There is a separate collections system for these products.
[xyz-ips snippet=”download-snippet”]