NextLight Core Pro – 210W LED Grow Light User Manual

NextLight Core Pro – 210W LED Grow Light User Manual

WARNING:: Please read and follow the instructions before installing and using your NextLight Core Pro

NextLight Core Pro – 210W LED Grow Light

• 2.6 PPF/W (μmol/J)
• DLC Hort Listed
• UL 8800
• IP65 Wet Rated
• Onboard Dimming
• External Dimming (Controller NOTINCLUDED)
• Passively Cooled
• 5 Year Full Warranty – All Components –Down to the Diode
• Designed for use in restricted spaces, openrooms, over benches, in racks or grow tents
• NextLight’s Full Spectrum is recommendedfrom seed to harvest
• Plug & Play – contains power & dimmingcords, power supply and mounting hardware.

The NextLight Core Pro is a high efficiency – bright white LED grow light designed to efficiently outperform your traditional 315W CMH or 400W MH. Harnessing the same high intensity light of the NextLight Mega Pro and redesigning it for use in smaller spaces. Excessive power consumption, bulb replacements and heat are among the biggest problems indoor growers face. The NextLight Pro Series alleviates all of those issues.

The NextLight Core Pro has the power and versatility for all stages and styles of indoor growing. Used primarily for high intensity flowering needs, the all new, Onboard Dimming feature allows for more control over desired light intensity. Output can be adjusted between 25%, 50%, 75% and 100%.

Please scan the QR code to access our online product listing for the NextLight Core Pro. There you can access more info, digital versions of this User Manual, Spec Sheets and more!

If you still have questions, please call 513.718.7556 or email [email protected]

Safety Recommendations and Warnings

WARNING: Please read and follow all Safety Recommendations and Warnings before installing your NextLight Core Pro

• Please check and adhere to all local rules, regulations and zoning codes when installing.
• The installer is responsible for correct and safe installation of light system.
• Prevent eye damage by avoiding direct eye contact with LEDs.
• Operate the light system within the temperature range of -4°F and 104°F.
• Mount the light system to something that can support the weight of the Fixture.
• Always allow for adequate ventilation of Fixture. Minimum 3″ from walls/ceiling.
• Do NOT hang Fixture by Power Cords.
• Ensure the local cabling can support the voltage and current of the light system.
• Only use Power Cords that were supplied with your light system.
• Do NOT use the Fixture with damaged Power Cords.
• Do NOT attempt to open, rewire or reconfigure any components of the light system. It will void the warranty and could cause serious injury or death.
• Disconnect the light system from power before performing any maintenance or repairs.
• Always disconnect power from the light system before moving or cleaning it.
• Do NOT clean the light system with detergents, abrasives or other aggressive substances.
• Do NOT use the light system near flammable, explosive or reactive substances.
• Do NOT use any Volatile Organic Compounds (VOCs) on or near the light system. VOCs can cause damage to LEDs (including insect foggers).
• The light system is certified for use in damp locations and is protected against water projected from a nozzle. Do NOT submerge light system.
• Avoid any contact or force with LED array that may damage LEDs.

Package Contents

1. Fixture x1
2. Fixture Hooks x2
3. NextLight Pro Series Power Cord (10’) x1(see available Power Cord Voltage Options)
4. NextLight Pro Series Control Cable (10’) x1

Power Cord Voltage Options

Technical Specifications

Product Dimensions

Onboard Dimmer

The Onboard Dimmer allows you to toggle Dim values of 0%, 25%, 50%, 75%, 100% and EXT for external use with NextLight Control Pro or NextLight Adapt Pro

Note: Onboard Dimmer must be set to EXT (External Control) for controller to operate. Pay special attention when using controller timing and shut off functionality as these functions will only work when the Onboard Dimmer is set to EXT

Product Installation

1. Take both Fixture Hooks and insert Hook ends through holes at each end of Fixture.
2. Use ratchet hangers to lift Fixture into place.
3. Connect the NextLight Pro Series Power Cord to the AC In on the Driver.
   • Insert Power Cord into AC In connection until an audible click is heard to ensure proper connection.
   • To remove connection, twist the locking ring counter clockwise and pull.
4. Adjust your Fixture height based on your desired light intensity needs.

Use with a Controller

To enable more precise Dimming Control and Programming on your NextLight Core Pro, you will need either a NextLight Control Pro or NextLight Adapt Pro.

• NextLight Control Pro enables Dimming Control, On/Off Timing, Sunrise/Sunset Programming and more. The NextLight Control Pro can control up to 500 NextLight Pro Series fixtures per controller (250 per Channel).
• B. NextLight Adapt Pro enables integration with most third party 0-10V controllers. This product adapts your third party 0-10V signal to NextLight’s proprietary signal flow.

Connecting Multiple Fixtures

• Insert NextLight Pro Series Control Cable into Channel A/B of your NextLight Control Pro or 485 Output of your NextLight Adapt Pro. Then screw the locking ring clockwise to ensure proper connection.
• Insert other end of Control Cable into Dim In connection on Driver of first Fixture in lighting system chain.
• Connect Control Cable from Dim Out on Driver of first Fixture to Dim In on Driver of next Fixture in the lighting system chain.
• Repeat until all Drivers/Fixtures are connected.

Proper Use and General Care

Follow steps below to help your light system retain peak performance.

• Hang Fixture using supplied Fixture Hooks.
• Hang Fixture at a minimum of 8″ from bottom of Fixture to top of plant canopy. Less than 8″ distance may burn plants.
• Always allow for adequate ventilation of Fixtures to ensure your lighting system can properly cool. Failure to do so may shorten the lighting system’s lifespan.
• Wipe down outside of Fixture with a damp rag. Dry thoroughly with a chamois or moist cellulose sponge to prevent water spots. All cleaning should be done with the light system unplugged from its power source.
• Avoid touching diodes with your hands, even if powered off.
• Never clean light system with detergents or abrasives.

NextLight Support

Please scan the QR code to access our online Support page, which includes theUser Manual, FAQ and additional Warranty Claim information.

nextlight.com/support

Five (5) Year Full Manufacturer’s Warranty

All NextLight products carry a Five (5) Year Full Manufacturer’s Warranty from date of purchase. Please follow all instructions and guidelines to ensure warranty is not voided. This warranty does not apply to any product which has been damaged, defaced, subjected to misuse, abnormal service or handling (including shipping damage) or which has been altered in design or construction.

To file a Warranty Claim, visit nextlight.com/warranty

Legal Disclaimer

NextLight products are to be used for lawful purposes only. It is the responsibility of you as the purchaser to know and abide by all laws pertaining to the use of NextLight products. NextLight, LLC will NOT be held liable for any unlawful state or federal activity arising out of the use of our products. By purchasing a NextLight product, you are agreeing to these terms and conditions, confirming that you as the purchaser are attesting to the lawful use of our product and are thereby solely responsible for acting in conformance with all applicable regulations.

Customer Support

Questions about your Questions about your NextLight Pro Series NextLight Pro Series products?

report this ad

Tell: 513.718.7556Email: [email protected]Web: nextlight.com