ManualNikabe Outdoor TWSSpeakers S6Item: 90578
www.nikabe.comBox 50435 MalmoSweden 2021.06-09
Overview
Buttons
- Reset button
- LED indicator
- DC input
- Power
Specifications
| Bluetooth version: | 5.0 |
| Bluetooth range: | 25 m |
| TWS range: | 20 m |
| Remote control range: | 20 m |
| Woofer: | 5.25″ IMPP Cone; Butyl Rubber Surround |
| Tweeter: | 0.75′ PEI dome |
| Frequency range: | 70 HZ-20 KHz |
| Sensitivity: | 86± 3 dB |
| IP rating: | IP44 |
| Size: | 178x150x237 mm |
| Wireless frequency: | 2.4 GHz – 2.48 GHz |
| Transmission power: | 20 mW (max) |
Included
2x speakers, 2x power adapter, 2x mounting brackets, 4x mounting screws, lx user manual, ix remote control
Installation
Location
Place or mount the speakers above ear level. The ideal distance between the speakers is 2.5 meters (max. distance 20 meters). Also, mind the location of the power source when choosing the speaker location.If you are going to mount the speakers outside, the ideal place is under eaves as they provide protection for the speakers, and therefore longevity. If it is possible, tilt the speakers downwards as well to get further protection from weather elements.Note! Keep the speakers inside during autumn and winter. The speakers should not be used in temperatures below 0 °C or above 45 °C.
Mounting
When mounting the speakers, use the included brackets and screws.Use the screws to mount the brackets and attach the speakers to the brackets using the large bracket knobs.To attach the speaker to the bracket, screw the bracket knobs into the cabinet. Point the speaker toward the listening area. When the speaker has been aligned, tighten the bracket knobs.
Use
Master and receiver speakerThe label on the back of the speakers is marked ‘Left” and “Right” respectively. The left speaker is the master speaker, and the right speaker is the receiving speaker.Pairing with BluetoothTurn on the master speaker with the Power switch (3). The speaker enters Bluetooth pairing mode. Open the Bluetooth settings on your Bluetooth device. Look for “Nikabe 56′ and connect. The LED indicator turns solid blue and the speaker says “Connecter when the pairing is successful. Pairing occurs automatically when you turn on the speaker the next time.Disconnect BluetoothPress and hold the TWS/Pair button on the remote control for 3 seconds to disconnect the currently paired Bluetooth device. The speaker goes into Bluetooth pairing mode and the indicator starts flashing blue.Connect TWSTurn on both speakers. The speakers enter TWS pairing mode (True Wireless Stereo). Wait for the speakers to connect. When the connection is successful, you will hear a prompt. If the speakers do not enter TWS paring automatically, press the TWS/Pair button on the remote control.Disconnect TWSPress 5 times on the TWS/Pair button on the remote to disconnect TWS.If the master speaker is turned off and the MS mode is active, the receiver speaker automatically searches for the master speaker. The LED will flash red. When the master speaker is not found, the receiver speaker starts searching for a Bluetooth device. The indicator starts flashing blue.LED indicatorBluetoothSearch for a Bluetooth device: Indicator flashes blue.Bluetooth device connected: The indicator is solid blue.Music is playing through Bluetooth: The indicator is solid blue.TWSTWS pairing: The indicator flashes red.TWS connection was successful: Master indicator turns blue; receiver indicator turns off.TWS disconnected: Indicator flashes blue.ResetPress and hold the Reset button (1) on the speaker for 5 seconds to clear all paired Bluetooth devices, or press and hold the Power button on the remote control for 10 seconds.
Remote Control
Power on/offPress the Power button to turn the speakers on.Press and hold the Power button for 3 seconds to turn the speakers off.Press and hold the Power button for 10 seconds to clear paired Bluetooth devices.TWS/ PairPress the TWS/Pair button to activate the TWS pairing.Press 5 times to disconnect TWS.Press and hold the button for 3 seconds to disconnect the currently paired Bluetooth device.MutePress the Mute button to mute the speakers. Press Mute, Vol+, or Vol- to unmute the speakers.
Safety information
Read the instructions in the manual and on the units before use to avoid a hazard. Use with provided adapters only.Do not place any open flame sources, such as lit candles, on or near the speaker. Do not attempt to service or disassemble the units yourself.If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified personnel in order to avoid a hazard.Unplug the units from the power supply during lightning storms.Never insert any objects into the units, as you could then touch dangerous voltage points or short-circuit parts that could lead to fire or electric shock. Make sure that objects do not fall on the speakers and that liquid is not spilled on the speakers.
Specification for power supply
| Input: | AC 100-240 V – 50/60 Hz, 0.5 A max |
| Output: | 15 V, 1.5 A, 22.5W |
| Average active efficiency (%) | 86.40 % |
| Efficiency at low load (10%) | 78.01 % |
| No-load power consumption (W) | 0.09 W |
report this adSimplified EU Declaration of Conformity
Kjell & Company hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Full text of the EU declaration of conformity is available at www.kjell.com/90578
[xyz-ips snippet=”download-snippet”]