NISBETS DA396 Contact grill Instruction Manual
Safety Tips
- Position on a flat, stable surface.
- A service agent/qualified technician should carry out installation and any repairs if required. Do not remove any components on this product.
- Consult Local and National Standards to comply with the following:
- Health and Safety at Work Legislation
- BS EN Codes of Practice
- Fire Precautions
- IEE Wiring Regulations
- Building Regulations
- Caution! Hot surface! The temperature ofthe heating surface and other accessible surface is very high during use. Touch the temperature control knob only.
- DO NOT immerse th appliance in water.
- DO NOT clean with jet/ pressure washers.
- DO NOT move or carry the appliance when it is switched on.
- DO NOT leave the appliance unattended during operation.
- Always use oven gloves when cooking or carrying out any adjustments to the appliance.
- Where this appliance is to be positioned in close proximity to a wall, partitions, kitchen furniture, decorative finishes, etc., it is recommended that they be made of non-combustible material; if not, they shall be clad with suitable with non-combustible heatinsulating material, and the closest attention be paid to fire prevention regulations.
- Do not obstruct any ventilation openings in the appliance body.
- Always use the black handle to lift the plate.
- Always switch off and disconnect the power supply to the appliance when not in use.
- This appliance must only be used in accordance with these instructions and by persons competent to do so.
- Keep all packaging away from children. Dispose of the packaging in accordance to the regulations of local authorities.
- If the power cord is damaged, it must be replaced by a Nisbets Essentials agent or a recommended qualified technician in order to avoid a hazard.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
- Nisbets Essentials recommend that this appliance should be periodically tested (at least annually) by a Competent Person. Testing should include, but not be limited to: Visual Inspection, Polarity Test, Earth Continuity, Insulation Continuity and Functional Testing.
- Nisbets Essentials recommend that this product is connected to a circuit protected by an appropriate RCD (Residual Current Device).
Introduction
Please take a few moments to carefully read through this manual. Correct maintenance and operation of this machine will provide the best possible performance from your Nisbets Essentials product.
This appliance is intended to be used for commercial applications, for example in kitchens of restaurants, canteens, hospitals, etc. but not for household and industrial use.
Pack Contents
The following is included:
- Contact Grill (Ribbed/Flat) – 1.8kW
- Waste tray
- Brush
- Instruction manual
Nisbets Essentials prides itself on quality and service, ensuring that at the time of packaging the contents are supplied fully functional and free of damage.
Should you find any damage as a result of transit, please contact your Nisbets Essentials dealer immediately.
Operation
Installation
- Place the unit on a heat-resistant surface. Avoid placing it on or close to flammable materials. Maintain a distance of 20cm (7 inches) between the appliance and walls or other objects for ventilation.
- Keep the unit away from splashing water and counter top’s edge
Note: Before using for the first time, clean the appliance with warm soapy water. Let dry completely.
Seasoning the Griddle PlateBefore using for the first time the cooking surface needs to seasoned.
- Ensure the cooking surface is clean.
- Brush the surface with cooking oil.
- Connect the appliance to the mains power supply.
- Turning on: Set the power switch to I position.
- Set the thermostat to 50°C. The HEAT indicator light turns on.
- Once the set temperature is reached, the HEAT indicator light turns off.
- Turn the appliance Off and allow to cool before wiping away any excess oil.
- The appliance is now ready for use.
Cooking
Note: It is recommend the cooking surface is lightly oiled before cooking.
- Close the plates.
- Connect the appliance to the mains power supply.
- Turn the appliance on. The power indicator light (green) illuminates.
- Set the thermostat to the desired temperature (50°C-300°C). The HEAT indicator light (orange) turns On and the appliance begins to heat upNote: 200°C to 220°C is suitable for general cooking.
- When the set temperature is reached, the HEAT indicator light turns Off.Note: During use, the HEAT indicator light will cycle on/off, indicating the set temperature is being maintained.
- Lift the upper plate and place the foodstuff on the lower plate.
- Lower the upper plate.
- Turning off: After use, set the thermostat to MIN position and power switch to O position.
Overheat protectionThis appliance is featured with an overheat protection. Should the temperature exceed safe levels the appliance will automatically cut off power.
The thermal Cut-out switch is located on the rear of the appliance. To reset the appliance after a sufficient cool-down period:
- Unscrew the reset switch cover.
- Press the small reset switch down until it clicks, using a blunt pointed instrument.
- The appliance is now reset and can be used as normal.
Cleaning, Care & Maintenance
Warning:
- Always turn off and disconnect the appliance from the power supply before cleaning.
- Always allow the appliance to cool before cleaning.
If grease is permitted to accumulate, it will begin to carbonised into a hard substance that is extremely difficult to remove. To prevent this follow the cleaning steps below:
- Regularly remove excess grease or fat using a cloth dampened with hot soapy water.
- Take care when using scrapers to remove cooking residues as they can damage the cooking surface.
- Dry thoroughly after cleaning.
- A Nisbets Essentials dealer or qualified technician should carry out repairs if required.
For best performance, Nisbets Essentials recommend that the appliance is cleaned after each day of operation.Failure to clean the appliance regularly may result in premature activation of the thermal cut-out switch.
Scraping
- After each use, scrape the appliance with a soft plastic or wooden scraper to remove excess fat and food.
- If there is an accumulation of burned fat or food, the cooking surface should be thoroughly scoured and re-seasoned.
Caution:
It is vital that the cooking surface is re-seasoned after scouring.Do not use steel wool as it may leave shards that could contaminate food.
Waste Tray
- This appliance is featured with a waste tray to collect any liquid or fats that run off during cooking.
- At least once a day, remove and empty the waste tray before washing with warm soapy water. Do no allow the tray to overfill.
Warning: DO NOT remove the tray during or immediately after use as the contents are still hot.
Troubleshooting
If your Nisbets Essentials appliance develops a fault, please check the following table before making a call to the Helpline.
| Fault | Probable Cause | Solution |
| The unit is not working | The unit is not switched on | Check the unit is plugged in correctly and switched on |
| Plug or lead is damaged | Call Nisbets Essentials agent or qualified technician | |
| Fuse in the plug has blown | Replace the plug fuse | |
| Power supply | Check power supply | |
| HEAT indicatorlight comes on but appliance does not heat up | Faulty element | Call Nisbets Essentials agent or qualified technician |
| Faulty thermostat | Call Nisbets Essentials agent or qualified technician | |
| Thermostat set incorrectly | Check thermostat | |
| Appliance slow to heat up | Cooking surface not clean | Clean cooking surface |
| Faulty element | Call Nisbets Essentials agent or qualified technician | |
| Surface flaking | Build up of carbonised food debris | Refer to “Cleaning, Care & Maintenance” section |
| No power | Thermal cut-out switch has activated | Press re-set switch on rear of unit |
Technical Specifications
|
Model |
DA396 |
| Voltage |
220-240V~ 50Hz-60Hz |
|
Power |
1800W |
| Current |
7.8A |
|
Dimensions h x w x d (mm) |
200 x 310 x 360
|
| Weight |
13kg |
Electrical Wiring
This appliance is supplied with a 3 pin BS1363 plug and lead.The plug is to be connected to a suitable mains socket.
This appliance is wired as follows:
- Live wire (coloured brown) to terminal marked L
- Neutral wire (coloured blue) to terminal marked N
- Earth wire (coloured green/yellow) to terminal marked E
This appliance must be earthed.If in doubt consult a qualified electrician.
Electrical isolation points must be kept clear of any obstructions. In the event of any emergency disconnection being required they must be readily accessible.
Compliance
The WEEE logo on this product or its documentation indicates that the product must not be disposed of as household waste. To help prevent possible harm to human health and/ or the environment, the product must be disposed of in an approved and environmentally safe recycling process. For further information on how to dispose of this product correctly, contact the product supplier, or the local authority responsible for waste disposal in your area.
Nisbets Essentials parts have undergone strict product testing in order to comply with regulatory standards and specifications set by international, independent, and federal authorities.
Nisbets Essentials products have been approved to carry the following symbol:
All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means, electronic, mechanical,photocopying, recording or otherwise, without the prior written permission of Nisbets Essentials.Every effort is made to ensure all details are correct at the time of going to press, however, Nisbets Essentials reserves the right to changespecifications without notice.
References
[xyz-ips snippet=”download-snippet”]