NITECORE NFZ100 Smart Camera Battery User Manual

NITECORE NFZ100 Smart Camera Battery User Manual

Product Introduction

The NFZ100 is a smart camera battery designed and developed by NITECORE compatible with Sony α7 III, α7R III, α9 (ILCE-9). With an iOS/Android app in your smartphone, you can check the real-time information of the battery health, battery level, charging/discharging current and other status of several batteries simultaneously. It is also equipped with a power balance circuit and Storage Mode to maximize its lifespan.


  • Type: Rechargeable Li-ion Battery
  • Voltage: 7.2V
  • Capacity: 2,280mAh
  • Energy: 16.4Wh
  • Operating Temperature: Charge: 0℃~45℃ (32℉~113℉)
  • Discharge: -20℃~60℃ (-4℉~140℉)
  • Compatible models: α7 III, α7R III, α9 (ILCE-9)
  • Dimensions: 52mm×38.7mm×22.5mm (2.05″×1.52″×0.89″)
  • Weight: 82.5g (2.91oz)

(Please note that NITECORE will reserve the rights to make any alteration on the specifications or modification on the product design at any time and without prior notice.)


  • Specially Designed Mobile App – NNERGYIn NNERGY, you can check the real-time information of the current working status of your smart batteries, including Battery Health, Power Remaining, Battery Voltage, Charge Cycles, Estimated Time to FULL/EMPTY, and Activation Date.(Android 5.0 / iOS 9.0 or above required)Scan to Download Our Mobile App – NNERGY
  • Built-in Battery Protection CircuitThe built-in battery protection circuit provides multiple protection safeguards including overcharge protection, over-discharge protection, overvoltage protection, overcurrent protection and short-circuit protection.
  • Built-in Smart Cell Management SystemThe OTA upgradeable management system is available to monitor the real-time working status of the cell. The power balance circuit is able to balance the working status of each cell to maximize the lifespan of the battery. After the Storage Mode is activated, the battery will be automatically discharged to the appropriate power level after it is left unused for 10 days.


  1. Before the first use, please fully charge the battery to activate it. The battery will not be detected by NNERGY unless it is successfully activated.
  2. Please recharge the product every 3 months when left unused for a prolonged time.
  3. When the product is charged within the camera body, a low charging efficiency might occur. Therefore, it is recommended to use the original charger of Sony or the NITECORE USN4 Pro to ensure a regular charging speed.
  4. Upgrade the firmware of the product when there is a pop-up upgrade notice in NNERGY to ensure a better user experience. During the firmware upgrade process, please put your smartphone close to the product. Please try again if the upgrade fails.
  5. Due to the regular upgrade of the camera firmware from time to time, the display might show a safety warning after the product is inserted into the camera. Please select “OK” to continue using the product.

Operating Instructions of NNERGY

  1. Enter NNERGY in your smartphone, and it will show the activated smart batteries detected nearby.
  2. Tap the red star beside the battery icon, insert the last 3 digits of the SN code shown on the label of the battery and select “OK” to successfully mark the battery. (For example, if the label shows SN:Z012019001, please insert 001.)Please mark all your batteries properly when you use them for the first time.
  3. Tap the battery icon to check the battery info.
  4. The Storage Mode icon ( ) is located on the upper right corner of the battery info interface. After the Storage Mode is activated, your battery will be automatically discharged to 70% after it is left unused for 10 days as it is the ideal storage status to be kept for a prolonged time.


  1. Please use the product only in the specified camera models.
  2. DO NOT use chargers of poor quality to charge the product to avoid accidents.
  3. Moderate heat from this product is to be expected during the charging process, which is normal.
  4. DO NOT leave the product unattended during the charging process. Cease the charging process once at any sign of malfunction.
  5. Operating Temperature: Charge: 0℃~45℃ (32℉~113℉) Discharge: -20℃~60℃ (-4℉~140℉)
  6. DO NOT expose the product to high temperature or incinerate. Avoid using the product in extreme environments where drastic changes in temperature are possible.
  7. DO NOT short-circuit the product, or it will lead to battery leakage, massive heat or even explosion.
  8. Avoid any shock or impact to the product.
  9. DO NOT leave the product unused in the camera for a prolonged time, or it will lead to battery leakage, malfunction and corrosion of the device.
  10. DO NOT use the product if any malfunction occurs such as giving off smoke or a peculiar smell.
  11. DO NOT disassemble or modify the product as doing so will render the product warranty invalid. Please refer to the warranty section in the manual for complete warranty information.


This product is globally insured by Ping An Insurance (Group) Company of China, Ltd.NITECORE shall not be held responsible or liable for any loss, damage or claim of any kind incurred as a result of the failure to obey the instructions provided in this user manual.

Warranty Details

Our authorized dealers and distributors are responsible for warranty service. Should any problem covered under warranty occurs, customers can contact their dealers or distributors in regards to their warranty claims, as long as the product was purchased from an authorized dealer or distributor. NITECORE’s Warranty is provided only for products purchased from an authorized source. This applies to all NITECORE productsAny DOA / defective product can be exchanged for a replacement through a local distributor/dealer within 15 days after the battery is activated. After 15 days, all defective / malfunctioning NITECORE® products can be repaired free of charge for a period of 12 months (1 year) from the date of activating the battery.

The warranty is nullified if the product(s) is/are:

  1. broken down, reconstructed and/or modified by unauthorized parties
  2. damaged from wrong operations

For the latest information on NITECORE® products and services, please contact a local NITECORE® distributor or send an email to [email protected].

  • All trademarks and product images herein this user manual are for reference purpose only. The copyright belongs to their legal owners.
  • All images, text and statements specified herein this user manual are for reference purpose only. Should any discrepancy occur between this manual and information specified on, information on our official website shall prevail. SYSMAX Communication Technology Co., Ltd. reserves the rights to interpret and amend the content of this document at any time without prior notice.

SYSMAX Communication Technology Co., Ltd.

TEL: +86-20-83862000FAX: +86-20-83882723E-mail: [email protected]Web: www.nitecore.comAddress: Rm 2601-06, Central Tower, No.5 Xiancun Road, Tianhe District, Guangzhou, 510623, Guangdong, China

Manufacturer: SYSMAX Power Technology, LLC

Please find us on facebook: NITECORE photo

Made in China

report this ad




[xyz-ips snippet=”download-snippet”]