NOAM Audio System with Bluetooth Marine 4 UTAH ATV Boat Owner’s Manual

Table of Contents

NOAM Audio System with Bluetooth Marine
4 UTAH ATV Boat Owner's Manual

WARNING:This product can potentially expose you to chemicals including lead, nickel and chromium which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

Thank you for making NOAM your choice for marine audio entertainment! Its compact, Marine design provides flexible mounting possibilities, and makes it simple to expand the audio system capabilities of your vehicle.

NUTV44 Channel Marine UTV/ATV/BOAT Audio System with Bluetooth®

One Pair 4″ 2-Way Marine Speaker:• 4″ High Quality Poly Injection Cone• Butyl Rubber Surround• Shinny Black Plastic Enclosure• Fits 1.5″-2″ Bars• 1″ High Temperature KEISV Voice Coil• 1″ PEI Neodymium Dome Tweeter• 100 Watts• Frequency Response: 100-20KHz• Impedance: 4 Ohms

4 Channel Marine Power Amplifier• 4 x 100 Watts at 4 Ohms• Anti-Thump Turn-On• Soft Turn On/Off• Bluetooth® Streaming• AUX Input• Volume Gain Remote Control• T.H.D: <0.05%• S/N Ratio: >95dB• Channel Separation: >65dB• Frequency Response: 1 0Hz- 30kHz• Fuse : 1 x 20A• Bluetooth® 3.0 Technology• Bluetooth® Auto Connected While Power on• Bluetooth® Auto Disconnected While Aux-in (3.5mm Connector)• Easy and Quick Installed Handle-bar Mount Bracket is Included• Bluetooth® Console Dimension: 2.12″(W) x 1.16″(H) x 3.83″(L)• Amplifier Dimensions: 6.3″L x 3.67″W x 2. 11 “H

What is included?

When first unpacking your new amplified Marine speaker system, Please check first that the package contains all of the items below. If something is missing, contact the store where you purchased the product.

NUTV4• One Pair 4″ 2 Way Marine Speaker• One Piece 4 Channel Marine Power Amplifier• One Piece Bluetooth ® controller

Installation precautions

Before you drill or cut any holes, investigate your vehicle’s layout very carefully.Take special care when you work near the gas tank, fuel lines, hydraulic linesand electrical wiring.

Never operate the amplifier when it is unmounted. Attach all audio system components securely within the amplifier to prevent damage, especially in an accident.

Do not mount this amplifier so that wire connections are unprotected. in a pinched condition, in contact with any metal surfaces in your vehicle, or likely to be damaged by nearby objects.

Before making or breaking power connections in your system, disconnect the vehicle battery. Confirm that your head unit or other equipment is turned off while connecting the input jacks and speaker terminals.

If you need to replace the power fuse, replace it only with a fuse identical to that supplied with the amplifier, Using a fuse of a different type or rating may result in damage to your audio system or your amplifier which is not covered by the manufacture’s warranty.

SPEAKER INSTALLATION INSTRUCTIONS:

Please note: The below instructions refers to most common bar sizes; 1.5″, 1.75″ and 2″ but using the supplied rubber pads will allow yo u to mount these speakers on an y bar size measured be tween 1.5″ and 2″

Power and Speaker Wiring

Bluetooth® Pairing and Connection:

Connect Bluetooth® controller box to your device
Press and Hold for three seconds until power indicator lights (red)
The system will automatically go into pairing modeThe power indicator will turn red for about 4-6 seconds and then alternating red and blue (Bluetooth® blue Power red)Please be sure that Bluetooth® is turned ON. Select NOAM Audio on your device to connect Bluetooth® controller (if the Bluetooth® controller is connected the light will turn blue and not flash)
When the device is out of Bluetooth® range, Bluetooth® will be disconnected automatically and automatically reconnect when detected in range again. (If not please just repeat steps 2 and 3)
When Bluetooth® is disconnected or the 3.5mm AUX Input is plugged in, the power indicator will glow red.