AC-25Portable Battery-Operated Acoustic AmpUser Manual
Introduction
The NUX AC-25 is a portable battery-operated amplifier optimized for acoustic-electric guitars. It features 2 channels with separate controls, Bluetooth connectivity, an onboard tuner, and a dedicated tone editing app. Where there is AC-25 there is music.
Features
- 2 channels with separate controls
- Onboard Reverb Effects & Tuner
- Up to 4 hours of continuous playing time
- Bluetooth Connectivity for audio streaming and tone editing
- WeII-planed controls & 1/0
Control Panels
CHANNEL 1
CHANNEL 1
INPUT Jack1/4 W\'(6.35mm) INPUT Jack, accept both passive and active acoustic pickups.VOLUME KnobControls the input signal level for the Channel 1 input.BASS KnobBass frequency level control.MIDDLE KnobMiddle frequency level control.TREBLE KnobTreble frequency level control.TUNER ButtonPress this button to engage/disengage the built-in tuner.DisplayTuning display. For further information please refer to the TUNER description.Channel 2COMOBO JackXLR input or 1/4″(6.35mm) instrument input.VOLUME KnobControls the input signal level for the Channel 2 input.SEND KnobAdjusts the amount of reverb.Global ControlsREVERB KnobSets the overall reverb.MASTER KnobSets the overall output volume level.Control PanelsBLUETOOTH Button Press this button to engage/disengage the built-in Bluetooth function. For further information please refer to the Bluetooth description.POWER IndicatorLights are on steady when The amplifier is on.ON/OFF SwitchTurn-ON/OFF the amplifier.•Please turn down the mater volume before you turn on the amp.
Rear Panel
Rear PanelDC-IN JackPlugin the included power supply here to power/charge this amplifier. Use specified power supply only(DC 15V/2.5A Polarity: Negative tip).Charge IndicatorLights on steady during the charging process. Lights off automatically when the battery is fully charged.Low Batt. IndicatorThe LED indicator will light on when the battery level is low. For further information, please refer to the BATTERY description.PHONES Jack1/4 Composite audio signal output jack.NOTE: The amplifier will be muted when it’s plugged in.AUX-IN jack1/8 Line level AUX-IN jack. You can connect a CD player, MP3 player, or other device and playback sound in stereo.LINE OUT JackYou can connect a mixer, recording device, or another such device here.
SPEAKER CoverYou can take off the speaker cover by pulling the ribbon in the lower right corner.SPEAKER6.5″ inch full range speaker. + soundhole.STANDYou can use the folding stand, just pull it up when needed.
Operation Guide
TUNER
- Press the TUNER button to activate the built-in tuner.
- Adjust the tuning peg of each string according to the tuning visuals on the DISPLAY:
- When finishing up, press the TUNER button again to quiet the tuner mode.*The amplifier will be muted when TUNER is engaged.*Tuner ONLY works with CHANNEL 1.
BLUETOOTH®
- When you power on the amplifier the Bluetooth function will also be turned on automatically by default. You can turn off the Bluetooth function manually by holding down the BLUETOOTH button for 2 seconds.
- This green indicator will keep flash indicating the Bluetooth® module is ready for pairing. Go to the Bluetooth setting menu of Bluetooth enabled device, find the device named “NUX AC25”, tap to pair. You will hear a cue tone when the connection is established successfully.
BATTERYThis amplifier is equipped with rechargeable battery packs. You can use either the built-in battery packs or the included power supply to power up the amplifier. The Low Batt. the indicator will light on when the battery level is low. At this point, the amplifier cannot be powered up until the power supply has been plugged in to recharge the battery. The amplifier can be used normally while charging. After the battery is fully charged, this indicator will turn off automatically. A full charge can take up to 4 hours, a full charge allows up to 4 hours of use.* Use time may vary depending on your settings.
Connections & Examples of using AC-25
AC-25 Rear Panel
Connections & Examples of using AC-25
Technical Specifications
- Speaker: 6.5″ , 4ohm , 50W , 63Hz — 20kHz
- Sampling Rate: 44.1kHz
- A/D,D/A Convert: 24bit
- Signal Processing: 32bit
- Rated Power: 25W
- Input Level& Impedance:Channel 1 -10dBu /1 M OhmsChannel 2 -30dBu /2K OhmsAUX-IN +3dBu / 21k Ohms
- Phones Output : 250mW + 250mW
- Tuning Range: AO—C8
- A4 = 440Hz
- DC Power Supply: 15V/2.5A Negative Tip
- Battery Pack Capacity: 12.6V/3000mAh
- Dimensions: 280(L) x 218(D) x 220(H)mm
- Weight: 5Kg
Supplied Accessories: User Manual, Power Supply
*Specifications may change without notice.
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. My changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:-Reorient or relocate the receiving antenna.-Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.-Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC’s RF exposure guidelines, This equipment should be installed and operated with a minimum distance of 20cm the radiator your body: Use only the supplied antenna.
FCC RF exposure statement:The equipment complies with the FCC Radiation exposure limit set forth for uncontrolled environments. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
report this adCE mark for European Harmonized StandardsCE Mark which is attached to our company’s products of Battery mains the product is in full conformity with the harmonized standard(s) EN 61000-6-3:20071-A1:2011 & EN 61000-6-1:2007 Under the Council Directive 2004/108/EC on Electromagnetic Compatibility.
© 2020 Cherub Technology-All rights reserved. No part of this publication may be reproduced in any form without prior written permission of Cherub Technology.
www.nuxefx.comMade in china
[xyz-ips snippet=”download-snippet”]