oricom UHF030 Compact 5 Watt UHF CB Radio User Guide

UHF030 Quick Start Guide

For the full product user guide, please scan the QR code or visit www.oricom.com.au

https://oricom.com.au/wp-content/uploads/2018/01/OR016835-UHF030-User-Guide-amendment_08-28-18.pdf

Pack contents

  • Compact UHF CB Radio Transceiver
  • Heavy-Duty Microphone
  • Microphone mounting bracket
  • Transceiver mounting bracket
  • Pack of supplied mounting screws
  • Quick Start User Guide

Please read before installing or operating your Oricom radioThe operation of your UHF radio in Australia and New Zealand is subject to conditions in the following licenses: In Australia, the ACMA Radiocommunications (Citizen Band Radio Stations) and in New Zealand by MED the General User Radio License for Citizen Band Radio.When a new narrowband radio receives a transmission from an older wideband radio the speech may sound loud and distorted – simply adjust your radio volume for the best listening performance. When an older wideband radio receives a signal from a new narrowband radio the speech may sound quieter – simply adjust your radio volume for best listening performance. When operating a narrowband radio or Channel 41 – 80 interference is possible from wideband radios transmitting on high power or on adjacent frequency.The issues described above are not a fault of the radio but a consequence of mixed-use of wideband and narrowband radios.

This unit complies with all relevant Australian and New Zealand approval requirements AS/NZS 4365:2011

Need help? Contact Oricom SupportIf you need assistance setting-up or using your Oricom product now or in the future, call Oricom Support.

Australia(02) 4574 8888www.oricom.com.auMon-Fri 8 am – 6 pm AESTNew Zealand0800 67 42 66Mon-Fri 10 am – 8 pm NZST

Controls and Indicators

Front View

Rear View

Microphone

  1. Push to talk switch (PTT)
  2. Recall/Memory of Instant channel (P1)
  3. Recall/Memory of Instant channel (P2)
  4. Recall/Memory of Instant channel (P3)

LCD Icons & Indicators

1. TX indicator2. Busy indicator3. Open scan4. Priority scan5. Instant memory channels scan6. Repeater channel scan7. Roger beep indicator8. Memory active channel indicator 9. Channel display10. Instant channel P111. Instant channel P212. Instant channel P313. Duplex Channel On14. Busy channel lock On15. Priority Channel On16. 38 CTCSS Tone On

Warnings and Safety Information

WARNINGPotentially Explosive AtmosphereTurn your radio OFF when in any area with a potentially explosive atmosphere. Sparks in such areas could cause an explosion or fire resulting in injury or even death.NOTE: Areas with potentially explosive atmospheres are often, but not always clearly marked. They include fueling areas such as below deck on boats; fuel or chemical transfer or storage facilities; areas where the air contains chemicals or particles, such as grain, dust, or metal powders; and any other area where you would normally be advised to turn off your vehicle engine.Blasting Caps and AreasTo avoid possible interference with blasting operations, turn your radio OFF near electrical blasting caps or in a “blasting area” or in areas posted: “Turn off two-way radios.” Obey all signs and instructions.Electromagnetic Interference/CompatibilityNearly every electronic device is susceptible to electromagnetic interference (EMI). To avoid the possibility of electromagnetic interference and/or compatibility conflicts, turn off your radio in any location where posted notices instruct you to do so such as health care facilities.This radio is designed for operation on a 12 Volt battery system. It should not be connected directly to a 24 Volt system.CAUTIONWhen installing your radio in your vehicle, check that during installation you do not damage any wiring or vehicle components that may be hidden around the mounting position.Ensure the installation does not interfere with the operation of the vehicle and meets all regulatory and safety retirements for accessories fitted to your vehicle.For optimum performance, your radio needs to be installed correctly. If you are unsure about how to install your radio, we suggest you have your radio professionally installed by a UHF specialist or Auto electrician. When installing the radio, avoid mounting it close to heaters or air conditioners. Never press the PTT button before connecting the antenna to the radio.

Installation of Your Oricom Radio

report this ad

Wiring MethodsThere are two possible wiring configurations for connecting to the vehicle’s power supply.A. Radio stays ON when the ignition is switched OFFConnect the radio’s negative (black) lead to the vehicle chassis, or directly to the battery’s negative terminal. Connect the radio’s positive (red) lead via the 3 Amp fuse to the battery’s positive terminal. Alternatively, the positive lead could be connected at the fuse box at a point that has DC Power continuously available (preferably the battery side of the ignition switch) via the 3 Amp fuse.B. Radio turns OFF with the ignition switchConnect the radio’s negative (black) lead to the vehicle’s chassis, or directly to the battery’s negative terminal.The radio positive (red) lead should connect to an accessory point in the vehicle’s fuse box via the 3 Amp fuse.Antenna informationThe antenna (not supplied) is of critical importance to maximize your output power and receiver sensitivity. A poorly installed, inferior quality antenna, or one not designed for the correct frequency band, will give poor performance. You should only purchase an antenna designed for the 477MHz frequency band.Antenna installationTo obtain maximum performance from the radio, select a high-quality antenna and mount it in a good location.Never press the PTT before connecting an antenna to the radio.Optional accessories

SPE85 External speakerIf required, you may install an external (8 ohm, Minimum 5W power) speakerfitted with a 3.5mm plug (not supplied).Depending on the installation, it may be necessary to use an external speaker(not supplied) to give improved volume and clarity. This can be plugged into the external speaker (SP) socket on the rear of the unit.
MMM100 Magnetic microphone holder

Quick Overview of Basic Controls

Power ON/OFFRotate the power switch in a clockwise direction to turn the unit ON, adjust the volume to a comfortable level. Rotate the Power Switch counterclockwise until it clicks to turn off the power.Secondary Function ButtonsTo use the primary function (SCAN, DPX, MON) press the required button.To use the secondary function (MENU, PRI, CALL) press and hold the button for 2 seconds.To Select a ChannelPress the up or down keys to step upwards or step downwards one or more channels.Setting the Squelch LevelTo adjust the level of squelch use the rotary SQL control. Turning the control counterclockwise reduces the amount of squelch, and turning clockwise will increase the amount of squelch. To reduce the signals that you can hear, increase the squelch, to hear more signals which may include weak signals decrease the squelch.PTT (Push-To-Talk) buttonBefore transmitting always listen to the channel to make sure it is not being used by another operator. Select the desired channel. Press the PTT button on the microphone and speak normally into the microphone. Hold it approx. 7 cm from your mouth. Release the PTT button to end the transmission and listen for a reply.Factory ResetIf the radio’s display locks up or stops functioning properly, you might need to reset your UHF radio.Caution: This procedure clears all the information you have stored in your UHF radio.Before you reset your UHF radio, try turning it off and on again.If your UHF radio is still not functioning correctly you may need to reset the UHF radio.While holding the Channel up button, turn the radio on, only the LCD backlight will be on for 1 to 2 seconds.The radio will then return to its original factory out condition.

UHF CB channels and frequencies

Channel Tx Rx Channel Ti Rx
Freq Freq Freq Freq
MHZ MHz MHz MHz
01* 476.4250 476.4250 21 476.9250 476.9250
41* 476.4375 61‡
02* 476.4500 476.4500 22† 476.9500 476.9500
42* 476.4625 62‡
03* 476.4750 476.4750 23† 476.9750 476.9750
43* 476.4875 63‡
04* 476.5000 476.5000 24 477.0000 477.0000
44* 476.5125 64 477. 477.
05* 476.5250 476.5250 25 477.0250 477.0250
45* 476.5375 65 477. 477.
06* 476.5500 476.5500 26 477.0500 477.0500
46* 476.5625 66 477. 477.
07* 476.5750 476.5750 27 477.0750 477.0750
47* 476.5875 67 477. 477.
08* 476.6000 476.6000 28 477.1000 477.1000
48* 476.6125 68 477. 477.
9 476.6250 476.6250 29 477.1250 477.1250
49 476.6375 476.6375 69 477. 477.
10 476.6500 476.6500 30 477.1500 477.1500
50 476.6625 476.6625 70 477. 477.
11 476.6750 476.6750 31* 477.1750 477.1750
51 476.6875 476.6875 71* 477.
12 476.7000 476.7000 32* 477.2000 477.2000
52 476.7125 476.7125 72* 477.
13 476.7250 476.7250 33* 477.2250 477.2250
53 476.7375 476.7375 73* 477.
14 476.7500 476.7500 34* 477.2500 477.2500
54 476.7625 476.7875 74* 477.
15 476.7750 476.7750 35* 477.2750 477.2750
55 476.7875 476.7875 75* 4772875
16 476.8000 476.8000 36* 477.3000 477.3000
56 476.8125 476.8125 76* 477.
17 476.8250 476.8250 37* 477.3250 477.3250
57 476.8375 476.8375 77* 477.
18 476.8500 476.8500 38* 477.3500 477.3500
58 476.8625 476.8625 78* 477.
19 476.8750 476.8750 39 477.3750 477.3750
59 476.8875 476.8875 79 477. 4773875
20 476.9000 476.9000 40 477.4000 477.4000
60 476.9125 476.9125 80 477. 477.4125

* The primary use for these channels is repeater operation using 750 kHz offset. Channels 1-8 inclusive are used for mobile reception and channels 31-38  for mobile transmission. They may alsoEMC Technologies (NZ) LtdSTREET ADDRESS – 47 MacKelvie Street, Grey Lynn, Auckland, NZPhone: +64 9 360 0862 Fax: +64 9 360 0861POSTAL ADDRESS – PO Box 68 307, Newton, Auckland, New ZealandE-mail: [email protected]Page 11 of 23This report may not be reproduced except in full* The primary use for these channels is repeater operation using 750 kHz offset. Channels 1-8 inclusive are used for mobile reception and channels 31-38 for mobile transmission. Note that additional channels 41-48 and 71-78 are also available for repeater operation to supplement channels 1-8 and-31- 38 respectively as approved by the ACMA CBRS Class Licence in Australia and the MED GURL in New Zealand. In addition, any designated repeater channel may be used for simplex operation in areas where it is not used for repeater operation.† Speech telephony shall be inhibited on these channels.‡ At the time of production Channels 61, 62, and 63 are guard channels and are not available for use.Channel 5 and 35 (paired for Duplex repeaters) are reserved as emergency channels and should be used only in an emergency.CTCSS and DCS will not operate on these channels.A list of currently authorized channels can be obtained from the ACMA website in Australia and the MED website in New Zealand. Channel 11 is a calling channel generally used to call others and channel 40 is the customary road vehicle channel.Once contact is established on the calling channel, both stations should move to another unused “SIMPLEX” channel to allow others to use the calling channel.Channels 22 and 23 are for Telemetry and Telecommand use, voice communications are not allowed on these channels by law.Channel 9 and above are the best choices for general use in Simplex mode.

Express Warranty (Australia)

This Express Warranty is provided by Oricom International Pty Ltd ABN 46 086 116 369, Unit 1, 4 Sovereign Place, South Windsor NSW 2756, hereinafter referred to as “Oricom”.Oricom products come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a  major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Oricom warrants that the product is free from defects in materials or workmanship during the Express Warranty Period. This Express Warranty does not extend to any product from which the serial number has been removed or was purchased outside of Australia.Nothing in this Express Warranty excludes, restricts or modifies any condition, warranty, guarantee, implied term, right, or remedy pursuant to the Australian  Consumer Law and which may not be so excluded, restricted or modified. For such conditions, terms, guarantees, and warranties that cannot be  excluded, restricted or modified, Oricom limits the remedies available to the extent permitted in the relevant legislation.The Express Warranty Period will be 5 years from the date of purchase of the product evidenced by your dated sales receipt.You are required to provide proof of purchase as a condition of receiving Express Warranty services. You are entitled to a replacement product or repair of the product at our discretion according to the terms and conditions of this document if your product is found to be faulty within the Express Warranty  Period. This Express Warranty extends to the original purchaser only and is not transferable.Products distributed by Oricom are manufactured using new materials or new and used materials equivalent to new in performance and reliability. Spare parts may be new or equivalent to new. Spare parts are warranted to be free from defects in material or workmanship for thirty (30) days or for the remainder of the Express Warranty Period of the Oricom branded product in which they are installed, whichever is longer. During the Express Warranty  Period, Oricom will where possible repair and if not replace the faulty product or part thereof. All component parts removed under this Express Warranty become the property of Oricom. In the unlikely event that your Oricom product has a recurring failure, Oricom may always, subject to the Competition and  Consumer Act 2010, at its discretion, elect to provide you with a replacement product of its choosing that is at least equivalent to your product in performance.No change to the conditions of this Express Warranty is valid unless it is made in writing and signed by an authorized representative of Oricom.Oricom will not be liable under this Express Warranty, and to the extent permitted by law will not be liable for any defect, loss, damage, or injury arising out  of or in connection with a:

  1. Failure by you to adhere to the warnings and follow the instructions set out in this user guide for the proper installation and use of the product;
  2. Wilful misconduct or deliberate misuse by you of the product;
  3. Any external cause beyond our control, including but not limited to power failure, lightning or over voltage; or
  4. Modification to the product or services carried out on the product by anyone other than Oricom or Oricom’s authorized service provider.

How to make a claim under your Express Warranty in Australia Oricom has a simple warranty process for you to follow:

  • Please call or email our Customer Support Team, (02) 4574 8888 or [email protected].
  • A Customer Support Team member will verify after troubleshooting with you if your product qualifies under warranty. If so, they will give you a Product  Return Authorization number.
  •  We will then email or fax a Return Authorisation Form and a Repair Notice (if necessary), together with instructions on how to return the goods for warranty service.

Please note that if a Customer Support Team member advises that your product does not qualify for a return, this warranty does not apply to your product.  Products that are authorized to be returned to Oricom in Australia must include all of the following:

  • A completed Return Authorisation form
  • A copy of your Proof of Purchase (please keep your original copy)
  • The faulty product, including all accessories.

Send the approved returns to:Oricom International Pty LtdLocked Bag 658South Windsor NSW 2756 AustraliaPlease note that this Express Warranty excludes expenses incurred by you in returning any faulty product to us. You must arrange and pay any expenses incurred (including postage, delivery, freight, transportation or insurance of the product) to return the faulty product to us, however, we will arrange delivery of the repaired or replaced faulty product to you.Important InformationRepair NoticePlease be aware that the repair of your goods may result in the loss of any user-generated data (such as stored telephone numbers, text messages, and contact information). Please ensure that you have made a copy of any data saved on your goods before sending for repair. Please also be aware that goods presented for repair may be replaced by refurbished goods or parts of the same type rather than being repaired.

[xyz-ips snippet=”download-snippet”]


Posted

in

by