paxcess Robotic Pool Floor Cleaner Optimus User Manual

Table of Contents

User Manual

paxcess Robotic Pool Floor Cleaner Optimus (HJ2052)

Thank you for purchasing PaxcessRobotic Pool Cleaner. If you have any questions or issues, please contact our customer services team for further assistance.

Email: Free Call: (US) (877)-756-8666 Service Time: Mon.-Fri.: 9:00-17:00 PSTFacebook: @paxcessWebsite: www.paxcess.com

Important Precautions

In order to avoid any accident/damage, it is strongly recommended to ï¬x the power supply unit in 3.5m away from the swimming pool by using the safety rope (included in the package).
In order to prevent severe damage to the cleaner, never power on the unit when it is outside of the swimming pool.
The power cord must be connected to an appropriate earthed socket.
Hold the top handle when putting the cleaner into water or lifting out of the water, do not pull the cable. Before power on, make sure to empty the trapped air inside the cleaner (no more air bubbles coming from the cleaner and the cleaner is fully submersed on the pool bottom).
Before power on, make sure the filter be assembled in position and cable be fully released to avoid any winding, which could affect the cleaner’s performance or cause damage.
Please clean and wash the filter bag every time after use.
The cleaner should be stored in a cool and ventilated place, away from direct sunlight when not in use.
The power supply unit should be placed in a shaded area during working. In order to avoid overheating and potential damage of components, never cover the power supply unit.
Only authorized after sales service personnel should open the cleaner’s power supply unit and motor assembly, otherwise the warranty will be invalidated.
Do not use the cleaner beyond the working environment/conditions stated in this manual.
Make sure the PH of pool water is between 7.0-7.2. 12.This machine is for clean the pool only not for other purpose. Read carefully the user manual before use.

Attention

When put the cleaner into the water please hold the top handle make sure to empty the trapped air inside, then the cleaner can immerse into the pool floor.

When pulling cleaner out of water, suspend the cleaner above water for about 10-15 seconds to empty the water inside. Please holds the top handle only, never pull the cable.

Introduction

The robotic pool cleaner HJ2052 is a new type of highly efficient and energy-saving swimming pool cleaning robot. Through its advanced computer controlled program, it can clean the pool walls and bottom automatically. At the same time, it filters the pool water and gets rid of suspended particles without replace the pool water. It’s totally environmental-friendly. For safe operation, the cleaner works on 28V direct current. Please read this user manual carefully before use.

Safety

Power supply unit position :

Power supply unit needs to be placed in proper position so as to reach the distal end of pool for the cleaner, meanwhile as least 3.5m from pool edge.

Specifications

Operational Instructions

Panel

Filter cleaning

1. Slide the two clips according to the indications on top cover to open it and take out the filters.

2. Clean the filters.

Re-install the filters, pay attention to the good position and slide the two clips to close the top cover.

3. Foam Installation

Attention: If your robot is in good performance, please ignore this instruction.

The below instruction is only used for special situation where the robot has difficulties to climb the pool walls.

Stick two foams on the reverse surface of top cover (see below picture), make sure the two foams are in the middle part of top cover.

4. Roller-FoamIn order to ensure the performance of the machine for the first time use, it is normal and all right if the two rollers of the machine are wet at your receipt of the robot. And it is recommended that before each use, if the rollers are dry, please immerse the machine into water for 15-20 minutes and wait for the rollers to fully absorb water, then switch on.

Packing list

Trouble Shooting

The pool water condition must be within the following parameters:

Warranty

This product is covered by Paxcess warranty for 24 months(only for motor and Control box kit) from the date of purchase. Consumable parts are beyond of warranty which includes: Belt/Filter basket/Roller/Side cover
This warranty is void if the product has been altered, misused, or has been repaired by unautho-rized personnel

Email: Free Call: (US) (877)-756-8666 Service Time: Mon.-Fri.: 9:00-17:00 PSTFacebook: @paxcess

The following are excluded from Paxcess warranty cover:

Device purchased as 2nd hand, used, or from unauthorized sellers.
Damage resulted from misused and abusive action.
Damage resulted from chemical, fire, radioactive substance, poison, or liquid.
Damage resulted from natural disaster.
Damage caused to any 3rd party, person, object, and beyond Statement We can only provide after sale services for products that are sold by Paxcess, if you have purchased your unit from a different place, please contact the seller for return and warranty issues.