PERLESMITH PSSS1 Speaker Floor Stand Instruction Manual
Thank you for choosing this PERLESMITH product! At PERLESMITH we strive to provide you with the best quality products and services in the industry. Should you have any issues, please don’t hesitate to contact us at
Technical Support:1-800-556-6806 Mon-Fri 8am – 8pm(CST)Other Info:[email protected]lesmith.com(US）[email protected](CA)
UNPACKING INSTRUCTIONS AND IMPORTANT SAFETY INFORMATION
- Carefully open the carton, remove contents and lay out on cardboard or other protective surface to avoid damage.
- Check package contents against the Supplied Parts and Hardware List to assure that all components were received undamaged. Do not use damaged or defective parts.
- Not all parts and hardware included will be used. lf you require replacement parts, please contact our Technical Support line at 1-800-556-6806 or customer service at [email protected] (US)/ [email protected] (CA).
- Carefully read all instructions before attempting installation.
- If you do not understand the instructions or have any concerns or questions please contact our Technical Support line at 1-800-556-6806 or customer service at [email protected] (US)/[email protected] (CA).
- This product may contain moving parts. Use with caution.
- Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
TOOLS NEEDED
- Phillips Screwdriver
CONTENTS
- Base
- Post Extension
- Post Assembly
- 90 Degree Plate
- Square Plate
- Narrow Plate
Hardware kits
- Nail (x6)
- Nut (x6)
- Pad (x6)
- Sponge (x2)
- Plastic Nut (x2)
- Bolt 1/4″ x13.5mm (x2)
- Bolt M5x8mm (x2)
- Bolt M5X12mm (x4)
- Bolt 1/4″x12mm (x4)
- Bolt M4X12mm (x4)
- Washer M4/M5 (x4)
- Bolt M6x12mm (x4)
- Bolt #6-32 x 1 1/4″ (x2)
- Nut #6-32 (x2)
- Washer #6 (x2)
- Washer #6 x #14 (x4)
STEP 1 Attach the nails or rubber pads to the base feet
For carpets floor,screw the nails into the holes of the base.
OPT A
For marble or wooden floor, rotate and insert the rubber pads into the holes of the base.
OPT B
STEP 2A
Fasten the post assemblies to the bases(for regular lower height)
STEP 2B
Fasten the post extensions and post assemblies to the bases(for extra higher height)
The plastic packaging bag of the posts and bases come with yellow and blue labels. ONLY assemble the posts and base labelled THE SAME COLOR. Otherwise it will be difficult to assemble.
- STEP 2B-1 Secure the post assemblies [03] to the post extensions [02]
- STEP 2B-1 Fasten the post extensions [02] and post assemblies [03] to bases [01]
STEP 3 Adjust post assemblies to the desired height
STEP 4 Secure speaker to stand
Speaker option A: two thread inserts
Speaker option B1: keyhole insert
Speaker option B2: keyhole insert(Suitable for Samsung SWA-8500S, SWA-9000S Speakers)
- Slide the washer [O] into the bolt [M], then insert them into the keyhole.
- Tighten the nut [N] until the washer [K] is pulled firmly against the 90 degree plate [04].
Speaker option C: Thread holes located at the bottom of the speaker
STEP 5 Route the cables
All of us at PERLESMITH do appreciate your product purchase. We hope that you are as happy with your product as we designing and manufacturing it for you.We strive to provide you with the best quality products and services in the industry. If you have any questions please don’t hesitate to contact us at
Technical Support:
1-800-556-6806 Mon-Fri 8am – 8pm(CST)Other Info:[email protected](US）[email protected](CA)
[xyz-ips snippet=”download-snippet”]