Pest Tech Supersonic Flash Repeller User Manual

Pest Tech Supersonic Flash Repeller

Product View

Supersonic Flash Repeller with smart mode

Please read and understand these instructions and keep this manual for future reference. This item uses solar power to recharge the battery making sure it is always working. The Passive Infrared sensor (PIR) detects motion and triggers either or both the ultrasonic speaker emitting ultrasonic waves and/or sonic waves. You can also choose to activate the strong LED light flashes, depending on the mode you set. The (ultra)sonic waves and/or light flashes will chase unwanted animals.

Dear customerCongratulations on buying our Supersonic Flash Repeller, which will get rid of all kinds of pests in a humane and effective way. Because we want to provide our customers with the best products, we would like to know your opinion on this device. So we and other customers can benefit from your information. Thank you for your trust in us

Scan Me

Step 1: Take your smart phoneStep 2: Open your camera appStep 3: Point your camera at the QR code and open the linkStep 4: Write your review

Operation

  • The Repeller uses a strong ultrasonic wave and a sonic wave to frighten animals. As soon as an animal enters the range of the PIR Sensor, the waves are activated. Animals will feel uncomfortable and run away.
  • The Repeller also uses a strong flashing LED-light to chase animals away. When animals enter the range of the PIR Sensor, the LED-light will be activated. The strong lights will scare the unwanted animals.

You can choose to use the three options together or just one or two at a time. If you set the timer, the Repeller will be activated every 30 minutes.

Set up

Button “sonic” (left): You can adjust the sonic range. By turning the knob clockwise, you increase the strength of the sound and the range of protection.

The settings are as follows:

  1. Deer
  2. Foxes, raccoons and skunks
  3. Dogs, squirrels, opossums and chipmunks
  4. and 5. Cats, mice, rats and skunks

Button “frequency” (right): You can control and adjust the frequency. By turning the knob clockwise, the frequency will be increased.

Button “frequency” positions are as below:

  1. Off
  2. 13.5KHZ – 19.5KHZ To repeal animals such as mice, rats, dogs, foxes and marters.
  3. 19.5KHZ – 24.5KHZ To repeal animals such as cats, raccoons, badgers and skunks.
  4. 24.5KHZ – 45.5KHZ To repeal animals such as bats, birds, pigeons and rodents
  5. Alarm and strong flashing lights to repel animals such as raccoons, boars and martens.
  6. All functions working: mode 1, mode 2, mode 3, and strong flashing lights.
Timer setting (smart mode)

If you turn on the smart mode, the Repeller will be activated every 30 minutes, independent of animals being within the range of the PIR Sensor.

To Assemble and Install
  1. Remove the cover of the battery compartment and install the 3.7 V 18650 2000 mAh lithium battery. Then close the battery compartment (battery included).
  2. Place the unit pointed towards the area you want to protect (for example, in a flowerbed or mounted from a wall)
  3. Choose a place where the solar panel can catch the sunlight as long as possible.
  4. If you place the unit in the ground, insert the spike carefully (first connect the pole sections). Allow 12 centimeters or more of the spike to stick out of the ground. Please be careful not to damage the units, as this will affect the performance.
  5. The device can be inserted into the ground, mounted against a wall or you can place the top part directly on a flat surface.

Technical specifications

  • Infrared sensor angle: 120 degrees.
  • Detection range: 8 meters depending on animal size (the bigger the size, the larger the range).
  • Power supply: solar power 3.7 V 18650 2000 mAh lithium battery rechargeable with solar power or USB-cable.
  • A green light indicates the unit is activated.
  • When you charge the device with the USB-cable, the light will turn from red to blue when the battery is fully charged.

Battery issue warning

  1. If the rechargeable batteries are not used for over a month, the battery must be fully released. It is recommended to charge the batteries 3 to 5 hours before regular use.
  2. When rainy or cloudy weather lasts for up to a whole week, the device may stop functioning. It is recommended to then switch off the device and recharge the battery.
  3. If the battery will not be used for a long time, please replace the battery in the compartment. Remember that the quality of the batteries will affect the capacity and performance of the device.
  4. After use, please take your batteries to the recycling center for used electrical and electronic devices. Consult your local government for more information

Caution

  1. Some humans can pick up parts of the sonic sounds. We, therefore, advise placing the device as far from human living spaces as possible. Do not install the device in an area where children and babies play and sleep.
  2. Do not cover up the PIR sensor.
  3. To clean the device, use a damp cloth and mild soap with water. Do not use strong chemicals or abrasive cleaning agents as they may damage the device.

Humane solutions for Pest Control

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

,