PHILIPS Headphones TAT2236 User Manual

Headphones2000 SeriesTAT2236

User manual

Register your product and get support at www.philips.com/support

Important safety instructions

Hearing Safety

Danger

  • To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is.

Be sure to observe the following guidelines when using your earphones.

  • Listen to reasonable volumes for reasonable periods of time.
  • Be careful not to adjust the volume continuously upwards as your hearing adapts.
  • Do not turn up the volume so high that you can’t hear what’s around you.
  • You should use caution or temporarily discontinue use in potentially hazardous situations.
  • Excessive sound pressure from earphones and headphones can cause hearing loss.
  • Using headphones with both ears covered while driving is not recommended and may be illegal in some areas while driving.
  • For your safety, avoid distractions from music or phone calls while in traffic or other potentially dangerous environments.

General informationTo avoid damage or malfunction:Caution

  • Do not expose headphones to excessive heat
  • Do not drop your headphones.
  • Headphones shall not be exposed to dripping, splashing water.
  • Do not allow your headphones to be submerged in water.
  • Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives.
  • If cleaning is required use a soft doth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product.
  • The integrated battery shall not be exposed to excessive heat such as sunshine, fire, or the like.
  • The danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type.• Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, can result in an explosion;• Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas;• A battery subjected to the extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.

About operating and storage temperatures and humidity

  • Store in a place where the temperature is between -20°C (-4°F) and 50°C (122 °F) (up to 90% relative humidity.
  • Operate in a place where the temperature is between 0°C (32°F) and 45°C (113 °F) (up to 90% relative humidity.
  • Battery life may be shorter in high or low-temperature conditions.
  • Replacement of a battery with an incorrect type that can defeat a safeguard (for example, in the case of some lithium battery types);

Your True wireless earphones

Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/support.With these Philips True wireless earphones, you can:

  • enjoy convenient wireless handsfree calls;
  • enjoy and control wireless music;
  • switch between calls and music.

What’s in the box

Philips True wireless earphonesPhilips TAT2236

USB-C charging cable (for charging only)

Other devicesA mobile phone or device (e.g. notebook, PAD, Bluetooth adapters, MP3 players, etc) which supports Bluetooth and is compatible with the earphones (see ‘Technical data’ on page 8).Overview of your True wireless earphones
  1. LED indicator (Earphones)
  2. Multi-function button
  3. Microphone
  4. LED indicator (charging box)
  5. USB-C charging slot

Get started

Charge the batteryNote

  • Before you use your earphones for the first time, place the earphones in the charging box and charge the battery for 2 hours for optimum battery capacity and lifetime.
  • Use only the original USB-C charging cable to avoid any damage.
  • Finish your call before charging the earphones, as connecting the earphones for charging will power the earphones off.

ChargingConnect one end of the USB cable into the charging box, and another end into the power source.The charging box starts charging.

  • The charging process is verified by the LED light on the front panel.
  • When the charging box is fully charged, the light goes on.

Tip

  • The charging box serves as a portable backup battery for charging the earphones. When the charging box is fully charged, it supports 2 times full recharge cycle for the earphones.
  • Normally, a full charge takes 2 hours (for the earphones or charging box) by USB cable.

Pair the earphones with your Bluetooth device for the first time

  1. Make sure that the earphones are fully charged and powered off.
  2. Open the top cover from the charging box.The LED on both earphones flashes in white & blue alternately.The earphones are now in pairing mode and is ready to pair with a Bluetooth device (e.g. a mobile phone)
  3. Turn on the Bluetooth function of your Bluetooth device.
  4. Pair the earphones with your Bluetooth device. Refer to the user manual of your Bluetooth device.

Note

  • After powering on, if the earphones cannot find any previously connected Bluetooth device, it will automatically switch to pairing mode.

The following example shows you how to pair the earphones with your Bluetooth device.

  1. Turn on the Bluetooth function of your Bluetooth device, select Philips TAT2236.
  2. Enter the earphones password “0000” (4 zeros) if prompted.For those Bluetooth devices featuring Bluetooth 3.0 or higher, no need to enter a password.

Single earpiece (Mono mode)Take either right or Left earpiece out from the charging box for Mono use. The earpiece will power on automatically. There will be a voice “Power on” from the earpiece.Note

  • Take the second Earpiece from the charging box and they will pair each other automatically.

Pair the earphones with another Bluetooth deviceIf you have another Bluetooth device that you want to pair with the earphones, make sure the Bluetooth function in any other previously paired or connected devices is turned off.Press and hold over 5 seconds both left & right side simultaneously with the earpiece on-ear, release when Pairing voice prompt is heard.Note

  • The earphones stores 4 devices in the memory. If you try to pair more than 4 devices, the earliest paired device is replaced by the new one.

Use your headphones

Connect the earphones to your Bluetooth device

  1. Turn on the Bluetooth function of your Bluetooth device.
  2. Open the top cover from the charging box.The blue LED flashes.The earphones will search the last connected Bluetooth device and reconnect to it automatically.If the last connected device is not available, the earphones will enter pairing mode.

Tip

  • The earphones cannot connect to more than 1 device at the same time. If you have two paired Bluetooth devices, only turn on the Bluetooth function of the device that you want to connect.
  • If you turn on the Bluetooth function of your Bluetooth device after turning on the earphones, you have to go to the Bluetooth menu of the device and connect the earphones to the device manually.

Note

  • If the earphones fail to connect to any Bluetooth device within 5 minutes, they will turn off automatically to save battery life.
  • In some Bluetooth devices, the connection may not be automatic. In this case, you have to go to the Bluetooth menu of your device and connect the earphones to the  Bluetooth device manually.

Power on/off

Task

 Multi-function button

Operation
Turn the earphones on Open charging case’s lid
Turn the earphones off Earpiece put back to charging box and close the lid

Manage your calls and musicMusic control

Task

 Multifunction button

Operation
Play or pause music Right / Left earpiece Single tap
Skip forward Right / Left earpiece Triple taps
Adjust volume +/ Via mobile phone control

Call control

Task

 Multifunction button

Operation
Pick up Right / Left earpiece single tap
Hang up call Right / Left earpiece Tap and hold
Switch call during 3-way call Right / Left earpiece triple taps

LED indicator status

Headphones status

Indicator
The earphones are connected to a Bluetooth device. Blue LED flashes
The earphones are ready for pairing The blue & white LED flash alternately
The earphones are on but not connected to a Bluetooth device White LED blink every 1s (auto turn o‑ after 3min)
Low battery level (earphones) Blue LED blinks 2x every 5s
The battery is fully charged (charging box). LED will be off

The battery level of charging case

Indicator
Amber
White
LED goes off

Battery LED indicator on Bluetooth deviceIt will show a battery indicator on the Bluetooth device after being connected to earphones (refer to mobile phone operation).

Voice Assistant

Task

 Button

Operation
Trigger voice (Siri/Google) assistant Right / Left earpiece Tap and hold 2 seconds

Reset the earphones

If you encounter any pairing or connection issue, you can follow the following procedure to reset your headset.

  1. On your Bluetooth device, go to the Bluetooth menu and remove Philips TAT2236 from the device list.
  2. Turn off the Bluetooth function of your Bluetooth device.
  3. Press once on both earphones, and then press and hold for 5 seconds.
  4. After Blue LEDs finish flashing, return earphones to the charging box & close the lid.
  5. Follow steps in “Use your earphones-Connect the earphones to your Bluetooth device.”
  6. Pair the earphones with your Bluetooth device, select Philips TAT2236.

Technical data

  • Music time: 6 hours
  • Talk time: 6 hours
  • Standby time – 200 hours
  • Charging time: 2 hours
  • Lithium-ion battery 50 mAh on each the earpiece, Lithium-ion battery 410 mAh on charging box
  • Bluetooth version: 5.0
  • Compatible Bluetooth profiles:• HSP (Hands-Free Profile-HFP)• A2DP (Advanced Audio Distribution Profile)•AVRCP (Audio Video Remote Control Profile)
  • Supported audio codec: SBC
  • Frequency range: 2.402-2.480GHz
  • Transmitter power: < 10 dBm
  • Operating range: Up to 10 meters (33 feet)
  • Auto power off
  • USB-C port for charging
  • Low battery warning: available

Note

  • Specifications are subject to change without notice.

Notice

Declaration of conformityHereby, MMD Hong Kong Holding Limited declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.You can find the Declaration of Conformity on www.p4c.philips.com.Disposal of your old product and batteryYour product is designed and manufactured with high-quality materials and components, which can be recycled and reused.This symbol on a product means that the product is covered by European Directive 2012/19/EU.This symbol means that the product contains a built-in rechargeable battery covered by European Directive 2013/56/EU which cannot be disposed of with normal household waste.We strongly advise you to take your product to an official collection point or a Philips service centre to have a professional remove the rechargeable battery.Inform yourself about the local separate collection system for electrical and electronic products and rechargeable batteries.Follow local rules and never dispose of the product and rechargeable batteries with normal household waste.Correct disposal of old products and rechargeable batteries helps prevent negative consequences for the environment and human health.Remove the integrated batteryIf there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing of the headphones.
  • Make sure the earphones is disconnected from the charging box before removing the battery.
  • Make sure the charging box is disconnected from the USB charging cable before removing the battery.

Compliance with EMFThis product complies with all applicable standards and regulations regarding exposure to electromagnetic fields.Environmental informationAll unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer), and  polyethylene (bags, protective foam sheet.)Your system consists of materials that can be recycled and reused if disassembled by a specialized company.Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries, and old equipment.Notice of complianceThe device complies with the FCC rules, Part 15. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2.  This device must accept any interference received, including interference that may cause undesired operation.

FCC rulesThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between equipment and receiver
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.Canada:This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s).Operation is subject to the following two conditions: (1)This device may not cause interference. (2)This device must accept any interference, including interference that maycause undesired operation of the device.IC Radiation Exposure Statement:This equipment complies with Canada’s radiation exposure limits set forth for uncontrolled environments.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Trademarks

BluetoothThe Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holding Limited is under license. Other trademarks and trade names are those of their respective owners.SiriSiri is a trademark of Apple Inc., registered in the U.S. and other countries.GoogleGoogle and Google Play are trademarks of Google LLC.

Frequently asked questions

My Bluetooth earphones do not turn on.The battery level is low. Charge the earphones.I cannot pair my Bluetooth earphones with my Bluetooth device.The Bluetooth is disabled. Enable the Bluetooth feature on your Bluetooth device and turn on the Bluetooth device before you turn on the earphones.Pairing does not work.

  • Put both earphones into the charging box.
  • Make sure you have disabled theThe Bluetooth function of any previously connected Bluetooth device.
  • On your Bluetooth device, delete “Philips TAT2236” from the Bluetooth list.
  • Pair your earphones (see ‘Pair the earphones with your Bluetooth device at the first time’ on page 6).

The Bluetooth device cannot find the earphones.

  • The earphones may be connected to a previously paired device. Turn off the connected device or move it out of range.
  • Pairing may have been reset or the earphones have been previously paired with another device.Pair the earphones with the Bluetooth device again as described in the user manual. (see ‘Pair the earphones with your Bluetooth device at the first time’ on page 6).

My Bluetooth earphones are connected to a Bluetooth stereo-enabled mobile phone, but music only plays on the mobile phone speaker.Refer to the user manual of your mobile phone. Select to listen to music through the earphones.The audio quality is poor and crackling noise can be heard.

  • The Bluetooth device is out of range.Reduce the distance between your earphones and Bluetooth device, or remove obstacles between them.
  • Charge your earphones.

The audio quality is poor when streaming from the mobile phone is very slow, or audio streaming does not work at all.Make sure your mobile phone not only supports (mono) HSP/HFP but also supports A2DP and is BT4.0x (or higher) compatible (see ‘Technical data’ on page 10).

report this ad

Philips and the Philips Shield Emblem have registered trademarks of Koninklijke Philips N.V. and are used under license.This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited or one of its affiliates,and MMD Hong Kong Holding Limited is the warrantor in relation to this product.UM_TAT2236_00_EN_V1.0

References

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

, , ,