Wireless Speaker TAS4405
Wireless Speaker4000 seriesTAS4405
User manual
Register your p roduct and get support at www.phili ps.com/support
Contents
1 Important
2
Safety
2
2 Your wireless speaker
3
Introduction
3
What’s in the box
3
Overview
3
3 Get started
4
Charge the built-in battery
4
Install batteries for the microphone
4
Install a micro-SD card
5
4 Power on/off
5
5 Use Bluetooth devices
6
6 Micro-SD card mode
7
7 Mix your sound with an audio source7
Record
7
8 Product information
8
10 Notice
8
Compliance
8
Care of the environment
8
FCC Statement
9
Trademark notice
9
EN 1
1 ImportantSa fetyW arning· Never remove the casing of this product. · Never lubricate any part of this product. · Never place this product on otherelectrical equipment. · Keep this product away from directsunlight, naked fames or heat.· Read and follow these instructions. · Make sure that there is enough spacearound the product for ventilation. ·personnel. Servicing is required when the product has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the product, the product has been exposed to rain or mositure, does not operate normally, or has been dropped. · by the manufacturer. · Use only power supplies listed in this user manual. · Unplug this product during lightning stroms or when unused for long periods of time. · This product should not be exposed to dripping or splashing. · Do not place any sources of danger on thecandles). · Where the plug of the Direct Plug-inAdapter is used as the disconnect device, the disconnect device shall remain readily operable.2 EN
· Do not use this product near water. · Install in accordance with themanufacturer’s instructions. · Do not install near any heat sources wuchas radiators, heat registers, stoves, orproduce heat.This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference,including interference that may cause undesired operation of the device.L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1) L’appareil ne doit pas produire de brouillage; 2) L’appareil doit accepter tout brouillageradioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.TAS4405/37-MIC This device operates on a no-protection, no-interference basis. Should the user seek to obtain protection from other radio services operating in the same TV bands, a radio licence is required. For further details, consult Innovation, Science and Economic Development Canada’s document Client Procedures Circular CPC-2-1-28, Voluntary Licensing of Licence-Exempt Low-Power Radio Apparatus in the TV Bands.TAS4405/37-MIC Ce dispositif fonctionne sur une base de nonprotection, sans interférence. Si l’utilisateur cherche à obtenir la protection d’autres services de radio opérant dans les mêmes bandes de télévision, une licence de radio est requise. Pour plus de détails, consultez le document de Innovation, Science et Développement économique Canada Intitulé La circulaire CPC-2-1-28 sur les procédures clients, licence volontaire d’apparatus radio à faible puissance exempté de licence dans les bandes de télévision.
2 Your wireless speakerCongratulations on your purchase, and ZHOFRPHWR3KLOLSV7RIXOOEHQHÀWIURPWKH support that Philips offers, register your product at www.philips.com/welcome.IntroductionWith this speaker and microphone, you can · enjoy audio from a Bluetooth device, · enjoy audio from a micro-SD card, · one touch recording to micro-SD card.What’s in the boxPlease check and identify the contents of your package: · Wireless speaker · Wireless microphone · USB cable · Quick start guide · Safety sheet
AAA x 2
*%
TAPR802Quick start guide
Overview
1 4
2
5
8 967
a · Press and hold for 2 seconds to power on or off.b · Press to start or stop the recording of audio from both the wireless microphone and the speaker.c · Press to select Bluetooth or micro-SD card source.d / · Press to adjust the volume.e · Press to play or pause. · Press twice to skip to the next track.f Micro-USB charging port g Micro-SD card slot h Battery compartment lid i Microphone power switch
EN 3
3 Get startedAlways follow the instructions in this chapter in sequence.Charge the built-in batteryThe speaker is powered by a built-in rechargeable battery.Note · Fully charge the built-in battery before using.5V 1.5 A
LED indicator (Power)
Flashing redSolid redFlashing red/green alternatively Solid green
Being charged when powered off Fully charged when powered off Being charged when powered on Fully charged when powered on
Install batteries for the microphone1 Open the battery compartment lid. 2 Install 2 AAA alkaline batteries (notprovided) with the correct polarity.3 Close the battery compartment lid.
Connect the USB cable between the microUSB socket on the speaker and a USB socket on your computer or a charger.4 EN
AAA x 2
Install a micro-SD card1 Open the lid of the card slot. 2 Insert a micro-SD card (not provided) withthe pin side facing down till you hear a click.Then close the lid of the card slot.
4 Power on/off1 Press and hold for 2 seconds to poweron or off the speaker.
2 sec.2 Slide up the power switch to power on themicrophone. Mic up to 5 m wireless range
EN 5
5 Use Bluetooth devicesWith this speaker, you can enjoy audio from your Bluetooth device.Note· Make sure that the Bluetooth function is enabled onyour device.· Keep away from any other electronic device that maycause interference.1 Press and hold for 2 seconds to enterthe Bluetooth pairing mode.
Philips S440510m BEEP
2 sec.2 Select “Philips S4405″ in the Bluetooth liston your device. » If a message prompts for permissionIRU%OXHWRRWKFRQQHFWLRQFRQÀUPLW » If a password is required, enter 0000DQGWKHQFRQÀUP » The speaker beeps when successfullyconnected.
LED indicator (Bluetooth)
Flashing blue Solid blue
Bluetooth pairing Bluetooth connected
Note· To disconnect, disable the Bluetooth connection withthis product on your device or press again to switch to micro-SD card mode.
6 EN
6 Micro-SD card modeYou can enjoy audio from a micro-SD card that VWRUHVDXGLRÀOHV Press repeatedly to select the micro-SD source.The Bluetooth LED indicator will be turned off for micro-SD auto playback.
7 Mix your sound with an audio sourceNote · Do not directly point the microphone to the speakerto prevent microphone feedback.By using the wireless microphone, you can mix your sound with an audio source
Record
In the Bluetooth mode, press to start or stop the recording.
LED indicator (REC)
Flashing red Solid red
Error (no micro-SD card inserted or the card is full) Recording
EN 7
8 Product informationNote Product information is subject to change without priornotice.
General information
Power supply:Speaker driver Charging time (Speaker) Playtime Built-in Lithium battery (Speaker) Dimensions (Speaker) Weight (Speaker)
5V 1.5A 1.5” 2.5 hours6 hours 3.7V, 1500mAh105 x 105 x 38 mm 250 g
BluetoothBluetooth version Bluetooth rangeMicMic wireless range
V4.2 10 m / 32.1 ftmax 5m
10 Noticedevice that are not expressly approved by MMD Hong Kong Holding Limited may void the user’s authority to operate the product.ComplianceHereby, MMD Hong Kong Holding Limited declares that this product is in compliance with the essential requirements and other relevant the Declaration of Conformity on www. philips.com/support.Care of the environmentDisposal of your old product and batteryYour product is designed and manufactured with high quality materials and components, which can be recycled and reused.This symbol on a product means that the product is covered by European Directive 2012/19/EU.
8 EN
This symbol means that the product contains batteries covered by European Directive 2013/56/EU which cannot be disposed of with normal household waste.Inform yourself about the the local separate collection system for electrical and electronic products and batteries. Follow local rules and
never dispose of the product and batteries with normal household waste. Correct disposal of old products and batteries helps prevent negative consequences for the environment and human health. Removing the disposal batteries To remove the disposable batteries, see battery install section.For INSPIRATION onlyEnvironmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.FCC StatementThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Warning: expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio/TV technician for help.RF Warning Statement The device has been evaluated to meet general RF exposure requirements.The device can be used in portable exposure conditions without restriction.Trademark noticeThe Bluetooth ® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holidng Limited is under license. Other trademarks and trade names are those of their respective owners.EN 9
report this ad6SHFLÀFDWLRQVDUHVXEMHFWWRFKDQJHZLWKRXWQRWLFH3KLOLSVDQGWKH3KLOLSV6KLHOG(PEOHPDUHUHJLVWHUHGWUDGHPDUNVRI.RQLQNOLMNH3KLOLSV19DQGDUHXVHGXQGHUOLFHQVH 7KLVSURGXFWKDVEHHQPDQXIDFWXUHGEDQGLVVROGXQGHUWKHUHVSRQVLELOLWRI00’+RQJ.RQJ+ROGLQJ/LPLWHGRU RQHRILWVDIÀOLDWHVDQG00’+RQJ.RQJ+ROGLQJ/LPLWHGLVWKHZDUUDQWRULQUHODWLRQWRWKLVSURGXFW
References
[xyz-ips snippet=”download-snippet”]