POOLCANDY Splash runner Motorized Luxury Pool Lounger Instruction Manual

Table of Contents

SPLASHRUNNERMOTORIZED LUXURY POOL LOUNGER

INSTRUCTION MANUAL

Congratulations on your purchase of the Splash Runner® Motorized Pool Lounger from PoolCandy. You and your friends will enjoy hours of outdoor fun with this innovative product. Your Splash Runner features two propellers that enable you to drive and turn in all directions!The Splash Runner is easy to use, but be sure to use it safely. Before starting, please read this manual thoroughly, especially noting the safety and care. Keep this manual for reference. Your Splash Runner requires some assembly. This package includes one pool lounger. For each side of the pool lounger, it includes a battery case, a battery cover and handle, a control arm sleeve, and a motor assembly that encloses the propeller. Your Splash Runner also includes a repair kit, and this instruction manual.

For easy to follow video instructions, go to www.poolcandy.net/pages/support and click on Support or scan the QR code below:

http://www.poolcandy.net/pages/support

INFLATION

Your Splash Runner has three separate air chambers to inﬂate. The nozzles for the air chambers are located on the underside of the backrest, behind the headrest, and at the bottom of the lounger near the feet. The Splash Runner can be inﬂated by mouth, with a foot pump, or with an electric pump.To inﬂate, the Splash Runner with an electric pump, insert the pump nozzle into the air valve. The valves include a ﬂap to prevent air from ﬂowing back out of the chamber, so make sure to push the pump nozzle past the ﬂap, to ensure that air ﬂows freely. Be careful not to over-inﬂate.Be sure to securely close each valve cover after completing each section.

ASSEMBLY

Once the lounger has been inﬂated, repeat the following steps on both sides of your Motorized Pool Lounger. Be sure to assemble it on a raised surface to prevent the motor assembly from being damaged.

Step 1.Insert the control arm sleeves into the openings in the armrest on the inﬂatable. Be sure to push the sleeve in until the top area is level with the top of the inﬂated armrest.

Step 2.Slide the battery assembly into the control arm sleeve. Be careful not to damage the wire inside the battery assembly when sliding it into the sleeve.

Step 3.Unscrew the cap from the battery assembly and to open the battery compartment. Insert 6 D-cell batteries (not included) into the compartment, making sure to follow the polarity (+/-) as marked inside the compartment. When all batteries are inserted, replace the cover on the battery compartment, and secure the cover with the cap by pressing down and tightening clockwise.

Note: Make sure the cover is properly aligned with the battery compartment as you close the compartment. The cover and compartment are designed with notches to ensure correct alignment. Rotate the cover until the notches in the cover ﬁt into the notches in the compartment itself

Step 4.Connect the wires from the bottom of the battery compartment (which should now be underneath your inﬂatable) to the propeller assembly by inserting the male power plug from the battery into the female outlet on the propeller. Be careful not to damage the wires.

Step 5.Align the tabs on the propeller assembly with the openings in the download of the battery compartment. Slide the top stem from the propeller into the battery compartment downrod. Squeeze the tabs on the sides of the top stem of the propeller to allow the steam to fully insert. The propeller assembly and the battery compartment assembly should ‘click’ into place.

Step 6.Repeat the steps above on the other side of the raft. Be careful not to damage the propeller when moving your Splash Runner during assembly.

TESTING the SPLASH RUNNER

After completing the previous assembly steps, press the button on the handle to test the propeller. If the propeller doesn’t move, check to make sure that all electrical connections are complete, and that the battery cover is correctly aligned and completely closed.

HOW to USE YOUR SPLASH RUNNER

CONTROLLING the SPLASH RUNNER

Your Splash Runner is perfect for your backyard pool or a small lake. Because it contains propellers on either side, it enables you to move in all directions.

To move, press the buttons on both handles. These buttons will operate your propellers.
To drive forward, turn both handles so they are facing forward and press both buttons at the same time.
To drive in reverse, turn both handles so they are facing backward and press both buttons.
To turn right, turn either handle to the right. The angle of your turn will depend on how much you turn the handles to the right.
To turn left, turn either handle to the left. The angle of your turn will depend on how much you turn the handles to the left.
To move laterally towards the right, turn both handles right and press both buttons.
To move laterally towards the left, turn both handles left and press both buttons.
To rotate in a circle, face one propeller forward and the other backward and press the buttons.

DISASSEMBLY

To disassemble your Splash Runner, please follow these instructions: First, unscrew the cap from the battery compartment and remove the cover. Remove all batteries. It is a good idea to immediately replace the battery cover and cap so that you don’t lose them. Next, separate the propeller from the battery compartment assembly by squeezing the tabs where they are connected. Squeeze both tabs and pull the propeller down. Be careful not to pull the propeller out too fast or far, as this may damage the electrical wires.Finally, separate the electrical connection between the propeller and the wires from the battery compartment by pressing the small tab on the male plug and pulling it away from the female connection. Once the propeller is disconnected from the wiring on the battery compartment assembly, you can remove all parts from the inﬂatable.Note: Be sure to disconnect the electrical by pulling the plastic plugs, not the wires themselves. Pulling on the wires can damage the assembly.

REPAIRING the SPLASH RUNNER

Rough surfaces may puncture the Splash Runner. If the lounger gets punctured, use the glue and PVC from the repair kit to seal the punctured surface. Apply the glue on the damaged area and apply the supplementary PVC sheet. Wait approximately one minute after applying the PVC sheet for the glue to dry before handling your Splash Runner. You should wait 24 hours before using the Splash Runner in the water again.

www.PoolCandy.net

WARNING

Please read the User’s Guide carefully before operating the product.

Children under 14 years of age should not operate this product without parental supervision.
This product is designed for pool and lake use only. It may be used in ponds or small lakes only within the range of the user’s comfortable ability to swim to shore. Do not use in areas where there are strong currents, waves, or watercraft present which could create wakes. Do not use in any other body of water or saltwater.
This product is designed to hold one person not exceeding 300 lbs/135 kg.
Keep hands, hair, and loose objects such as clothing away from the propeller.
If an object becomes lodged in the propeller, make sure that this product is turned off before attempting to dislodge it.
Always inspect the pool area before use to ensure it is free of hazards and/or obstacles, such as pool toys and swimmers.
Never ride into or over swimmers.
Keep this product away from hot or sharp objects.
Always use caution and common sense.
Never jump or dive off this product.

SPECIAL CARE & HANDLING

Avoid rough handling such as bumping or dropping.
Avoid extreme temperatures. For best results use between the temperatures of 39° F and 120° F (4° C and 38° C).
Clean using only a slightly damp cloth. Do not use cleaners with chemical agents.

BATTERY INFORMATION

Your Motorized Pool Lounger uses 12 D batteries (6 per propeller), not included.
Do not mix alkaline, standard (carbon-zinc) or rechargeable nickel-cadmium) batteries.
Do not mix old and new batteries.
Do not use rechargeable batteries.
Remove exhausted batteries from the unit.
Do not short circuit battery terminals.
Remove batteries and store them in a cool, dry place when not in use.
To avoid explosion or leakage, do not dispose of batteries in a ﬁre or attempt to recharge alkaline or other non-rechargeable batteries.

If you have any questions or would like additional information on PoolCandy products, please contact us at [email protected].

THE MOTORIZED POOL LOUNGER IS NEITHER A PERSONAL-FLOTATION NOR A LIFESAVING DEVICE. ALL USERS SHOULD KNOW HOW TO SWIM.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/ TV technician for help.