Z-WeatherSKU: POPE005206
QuickstartThis is a Sensor for Europe. Please make sure the internal battery is fully charged. Push the button 3 times within 1.5 seconds. If the LED is not blinking aft releasing the button, Z-Weather has not had enough energy and must be charged for several hours in bright sunlight.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor, and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart sectionZ-Wave ensures reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise, it will automatically turn into a lower level of security to maintain backward compatibility.For more information about Z-Wave technology, devices, white papers, etc. please refer to www.z-wave.info.
Product Description
Z-Weather is a cup anemometer for Z-Wave installations. It continually measures the wind speed and can, for example, trigger closing of the awnings and blind too windy. It also measures the amount of rotation, enabling the calculation of the wind yield per day or per year. In addition, Z-Weather includes sensors for humid temperature, air pressure, and dew point, essentially providing the core sensors of a weather station. Z-Weather is powered by a solar cell and stores energy on the internal capacitor, enabling continuous operation, even with the little sun for a couple of days. It does not use any batteries and is completely maintenance-free. Using a built-in solar cell also measures the ambient light and the solar yield. This information can be used to turn on the outdoor light at dusk time and turn the light in o morning. Z-Weathers wind yield and solar yield metering can be used as a calculation base for planning a wind generator or a solar panel on the roof of a houseDuring normal operation, Z-Weather is limiting continuous measurement to wind speed and solar radiation, other sensors are operating only on demand. This conservative energy management ensures continuous operation with the limited energy harvested from the solar cell powering Z-Weather. The Z-Wave radio frequency transmitter is turned off most of the time and is turned on if there is too much wind, at a twilight time, and on a continuous base, depending on the energy budget. The wake-up interval is between five minutes at noon in summer and five hours in the second half of the night in winter. Z-Weather also wakes up on pu the button.
Prepare for Installation / Reset
Please read the user manual before installing the product.In order to include (add) a Z-Wave device to a network, it must be in a factory default state. Please make sure to reset the device into factory default. You can d by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to the primary controller of the previous network to make sure the very device is excluded properly from this network.Reset to factory defaultThis device also allows being reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable
Hold the button longer than 1.5 seconds and then release. The LED blinks longer than when pressing the button once.
Installation
Before you can configure and use Z-Weather, the unit needs to be fully charged. In order to charge Z-Weather place it in a location with direct sunlight exposure hours. Without Z-Weather: Operating elements Function Button and Status LED Solar Cell 3 direct sunlight the charging may take up to 12 hours. To check if Z Weather has been charged sufficiently, press the button located under the cup anemometer. If the LED blinks after pressing the button, Z-Weather is charged and operational.Most of Z-Weathers sensors are placed inside the top of the ball-bearing cup anemometer and they are measuring the environmental parameters inside the bla round housing. If the sun is shining and Z-Weather is placed in direct sunlight, the housing will warm up and the temperature is higher than the temperature outside the housing. Thus a place in the shadow is the best choice for placing Z-Weather. Even though Z-Weather is powered by a solar cell, it is not required to place Z-W exposed to direct sunlight and there is no need to face it south. The solar cell will produce sufficient energy to power Z-Weather, even if the solar cell is facing n and the device is in the shadow all day.
Inclusion/Exclusion
On factory default, the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. T controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion are then performed doing a special manual action right on the device.Inclusion
- Charge the device with solar radiation for approx. 24h.
- Press the button on the bottom of the device three times in succession.
Exclusion
- Charge the device with solar radiation for approx. 24h.
- Press the button on the bottom of the device three times in succession.
Product Usage
Z-Weather is maintenance-free and works environmentally friendly using solar power, it does not contain any batteries. The solar cell charges an internal capacitor that buffers all harvested energy and powers the electronic components during the night. When first operating Z-Weather after installation, it is required to fully charge the device by placing it in direct sunlight for 4-6 hours. Even though the capacitor is pre-charged at the factory, the capacitor has most likely lost most of the energy and does not provide sufficient power for operating Z-Weather immediately after unpacking. If the capacitor is completely empty it must be charged from 100% which takes longer than in subsequent charging cycles.Once Z-Weather is installed and operating, it is charged on a day-by-day base and the capacitor will never be discharged completely. If the capacitor is completely discharged, which only can happen at the time of delivery if Z-Weather was stored at a dark place for weeks, charging may need up to 6 hours in direct sunlight during summer and up to 2 days during the winter solstice and grey sky. In order to check the functionality of Z-Weather and test whether the device has sufficient energy to operate, press the button located under the anemometer. If the LED blinks, Z-Weather has enough energy to operate. 5 It is good practice to perform the initial set Z-Weather at noon. After the first charging cycle is completed, the device will have stored enough energy for setup and adding the device to the Z-Wave network. However, if you want to experiment with settings, or use the power-consuming POWERLEVEL command class, Z-Weather may quickly use up all its energy rese and may need to be charged again. If you configure Z-Weather at noon, the device had the entire morning for a full charge, has strong sunlight when it uses the energy (during configuration), and has the complete afternoon for recharging. As a rule of thumb: After pressing the button eight times, Z-Weather will have used energy stored. When the energy has been used up, the LED does not blink and Z-Weather needs to be charged for approximately 1-2 hours.
SENSOR _MULTILEVEL
Reports the following measurements:
| Measurement | Range | Accuracy |
| Air temperature | -10.0°C to +60.0°C | + 0.4°C |
| Luminance | 0 to 100% | ± 7% |
| Relative humidity | 1 to 100% | ± 3% |
| Wind speed | 0 to 31 rn/s | ± 1m/s |
| Barometric pressure | 600 to 1200 mBar | ± ImBar |
| Dew point | -56.4°C to +60.0°C | ± 0,7°C |
Node Information Frame
The Node Information Frame (NIF) is the business card of a Z-Wave device. It contains information about the device type and the technical capabilities. The incl and exclusion of the device are confirmed by sending out a Node Information Frame. Besides this, it may be needed for certain network operations to send out an N Information Frame. To issue a NIF execute the following action: Push the button 3 times within 1.5 seconds.Communication to a Sleeping device (Wakeup)
This device is battery-operated and turned into a deep sleep state most of the time to save battery life. Communication with the device is limited. In order to communicate with the device, a static controller C is needed in the network. This controller will maintain a mailbox for the battery-operated devices and store commands that can not be received during deep sleep state. Without such a controller, communication may become impossible, and/or the battery life is significantly decreased.This device will wake up regularly and announce the wakeup state by sending out a so-called Wakeup Notification. The controller can then empty the mailbox. Therefore, the device needs to be configured with the desired wakeup interval and the node ID of the controller. If the device was included by a static controller will usually perform all necessary configurations. The wakeup interval is a tradeoff between maximal battery lifetime and the desired responses of the device. To wake up the device please perform the following action: Push the button 3 times within 1.5 seconds. The LED blinks once indicating that Z-Weather is
Quick troubleshooting
Here are a few hints for network installation if things don’t work as expected.
- Make sure a device is in a factory reset state before including it. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise, you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Don’t poll FLIRS devices. 6. Make sure to have enough mains powered devices to benefit from the meshing
Association – one device controls another device
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are related to certain events (e.g. button pressed, sensor triggers, …). In case the event happens all devices stored in the respective association group will receive t same wireless command, typically a ‘Basic Set’ Command.
Association Groups:
| Group Number | Maximum Nodes | Description |
| 1 | Lifeline. | |
| 2 | 5 | Too windy If the threshold value for wind (Default value: 6m/s ) is exceeded, the basic set is all group members. |
| 3 | 5 | It is getting bright. Sends BASIC SET command in the morning when brightness reached a trig level (Default value: 37%) |
| 4 | 5 | It is getting dark.Sends BASIC SET command in the evening when brightness reached triggelevel (Default value: 37%) |
Configuration Parameters
Z-Wave products are supposed to work out of the box after inclusion, however, certain configurations can adapt the function better to user needs or unlock further enhanced features.IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 … 255 the value sent in the application shall be the d value minus 256. For example: To set a parameter to 200it may be needed to set a value of 200 minus 256 = minus 56. In the case of a two-byte value, the same lo applies Values greater than 32768 may need to be given as negative values too.Parameter 1: Threshold for too much windCrossing this value on the rising edge, Z-Weather sends a basic set to the associated groups, serves the lifeline, and sends a wake-up notification. Size: 1 Byte, Default Value: 6
| Setting | Description |
| 0 – 30 | m/s |
Parameter 2: Threshold for twilightThis parameter sets the trigger level for twilight to control devices in association groups 3 and 4Size: 1 Byte, Default Value: 37
| Setting | Description |
| 0 – 100 | % |
Technical Data
| Dimensions | 300x121x330 mm |
| Weight | 300 gr |
| Hardware Platform | ZM5202 |
| EAN | 0019962005206 |
| IP Class | IP 33 |
| Device Type | Sensor |
| Network Operation | Routing Slave |
| Firmware Version | 01.00 |
| Z-Wave Version | 04.05 |
| Certification ID | ZC10-15080003 |
| Z-Wave Product Id | 0x0154.0x0100.0x0400 |
| Frequency | Europe – 868,4 Mhz |
| Maximum transmission power | 5 mW |
report this adSupported Command Classes
|
|
Controlled Command Classes
- Association Command Configuration
- Language
- Multi-Channel
- Device Reset Locally
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways, Remote Controls, or battery-operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators, and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.
http://manual.zwave.eu/backend/make.php?lang=en&sku=POPE005206(c) 2020 Z-Wave Europe GmbH, Antonstr. 3, 09337 Hohenstein-Ernstthal, Germany,All rights reserved, www.zwave.eu. The template is maintained by Z-Wave Europe GmbH.The product content is maintained by Z-Wave Europe GmbH, Support team, [email protected]. Last update of the product data: 2020-02-0414:07:18
References
[xyz-ips snippet=”download-snippet”]