FUSION WIRELESS ARCADE STICKSTICK ARCADE SANS FIL FUSION
USER MANUALMANUEL DE L’UTILISATEUR
|
FRONT |
BACK |
SETUP
Check for system updates. Nintendo system update version 6.0.1 or later is required for use of PowerA Wireless controllers.
- Connect your Nintendo Switch to the Internet
- Typically, system updates will be downloaded automatically when connected online.
- Select ‘System Settings’ from the HOME Menu, then scroll down to ‘System’ to see the System Update version and automatically check for system updates.
For additional help, search ‘system update’ from the Nintendo Support website.BATTERY INSTALLATION
- Remove the battery door on the bottom panel and install (2) AA Alkaline Batteries (included).
- Confirm your Nintendo Switch Console is powered ON.
WIRED MODE
- Make sure your Nintendo Switch System is powered on and connected to your TV.
- Insert the USB cable into a USB port on the Nintendo Switch Dock. Connect the other end of the cable to the wired controller. Your wired controller is now ready for use.
- For wired mode, make sure the Arcade stick “battery mode” is turned off.
WIRELESS PAIRING
- The battery Mode switch should be “ON” for wireless mode.
- From the HOME Menu, select “Controllers,” then “Change Grip and Order.” While the pairing screen is displayed, press and hold down the SYNC Button for at least three seconds on the Arcade Stick you wish to pair.
NOTE: Once Arcade Stick is paired once, it will auto-connect next time.UNDERSTANDING LED INDICATORSThere are two LED locations on this Arcade Stick: top left and along the front edge.
- The front edge LED near the Sync button will flash Red when the Alkaline batteries are getting near depletion. Replace Alkaline batteries once the low battery indicator is flashing to avoid interrupting gameplay.
- The top-left LED location has four LEDs (in the control panel next to Home/View buttons) and indicates player numbers 1-8 and will cycle from left to right during wireless pairing.
INSTRUCTIONS
FACEPLATE REMOVAL
- Using a Phillips screwdriver, remove 6 screws on the face of the Arcade stick, and place them in a safe location.
- Next unscrew and remove the joystick knob, with a plastic sleeve and dust cover, and lift off the acrylic cover.
- Carefully remove the default face-card graphic and replace it with the new face card graphic.
- The reverse process above to re-assemble with a new face-card graphic in place.
D-PAD TOGGLE SWITCH
The D-Pad toggle switch can be changed on the fly to any of these three settings:DP: This will work as a normal 8-way D-padLS: This will convert the joystick into a digital emulation of the left thumbstick and how it is mapped in-game. This will be useful for games that do not support movement or commands from a D-pad.RS: This will convert the joystick into a digital emulation of the right thumbstick and how it is mapped to in-game functions. This will be useful for games that use the RS forcamera movements and other in-game features not supported using a D-pad.
For additional troubleshooting information, refer to the Nintendo Switch user manual.MOTION WARNINGPlaying video games can make your muscles, joints, skin, or eyes hurt. Follow these instructions to avoid problems such as tendinitis, carpal tunnel syndrome, skin irritation or eyestrain:
- Avoid excessive play. Take a 10 to 15-minute break every hour, even if you don’t think you need it. Parents should monitor their children for appropriate play.
- If your hands, wrists, arms, or eyes become tired or sore while playing, or if you feel symptoms such as tingling, numbness, burning, or stiffness, stop and rest for several hours before playing again.
- If you continue to have any of the above symptoms or other discomforts during or after play, stop playing and see a doctor.
CUSTOMER SERVICE
For support with your authentic PowerA accessories, please visit PowerA.com/Support.MANUFACTURED BYBensussen Deutsch & Associates, LLC. (BDA, LLC.) 15525 Woodinville-Redmond Rd. NE Woodinville, WA 98072. BDAINC.com | POWERA.comADDITIONAL LEGAL© 2020 Bensussen Deutsch & Associates, LLC. PowerA, the PowerA logo, and the Fusion logo are trademarks of Bensussen Deutsch & Associates, LLC, Woodinville, WA 98072.Manufactured and distributed under license by Nintendo. Nintendo Switch is a trademark of Nintendo. © 2020 Nintendo. All rights reserved. All other trademarks are the property of their respective owners.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
BATTERY WARNING
Do not attempt to replace the rechargeable battery yourself- you may damage the battery, which could cause overheating, fire, and injury. The Lithium-ion battery in your deviceshould be serviced or recycled by PowerA or an authorized provider and must be recycled or disposed of separately from household waste. Dispose of batteries according to your local environmental laws and guidelines.Do not use or leave the product containing rechargeable batteries exposed to very high temperatures (e.g. at strong direct sunlight or in a vehicle in extremely hot weather).Otherwise, it can overheat, catch fire, or the performance will degenerate, and the service life will be shortened.Do not use the rechargeable battery item in a location where static electricity is rich, otherwise, the internal safety devices may be damaged, causing a harmful situation.In case the electrolyte gets into the eyes due to the leakage of the battery, do not rub your eyes!Rinse eyes with clean running water and seek medical attention immediately. Otherwise, it may injure the eyes or cause a loss of sight.If the battery gives off an odor, generates heat, or in any way appears abnormal during use, recharging, or storage, immediately remove it from the battery charger and place it in a sealed vessel such as a metal box.Be aware discarded batteries may cause fire, do not heat the controller or throw it into the fire.CAN ICES-3(B)/NMB-3(B)This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesiredoperation of the device.
REGIONAL COMPLIANCE SYMBOLS
More information is available via web-search of each symbol name.The WEEE symbol informs the end-user about separate disposal requirements for WEEE (Waste of electrical and electronic equipment) as required per Article 11(2) of the WEEE Directive and prescribed by European standard EN50419:2005.CE (Conformité Européene aka European Conformity) is a certification mark that indicates conformity with health, safety, and environmental protectionstandards for products sold within the European Economic Area.The Regulatory Compliance Mark is a visible indication of a product’s compliance with all applicable ACMA (Australian Communications and Media Authority) regulatory arrangements, including all technical and record-keeping requirements regarding the electrical safety and/or electromagnetic compatibility (EMC).
WARRANTY
report this ad2-Year Limited Warranty: Visit PowerA.com for details.
CONTENTSWireless Arcade Stick | FUSION face-card graphic9.8ft (3m) USB-C cable with velcro strap2 x AA batteries | User guide2-YEAR LIMITED WARRANTY. VISIT POWERA.COM/SUPPORT FOR DETAILSBDA LLC., 15525 WOODINVILLE-REDMOND RD NE, WOODINVILLE, WA 98072
References
[xyz-ips snippet=”download-snippet”]