PRESTIGE APS510Z Security with Keyless Entry User Guide

APS510ZSecurity with Keyless Entry

Quick Installation Guide

Alarm

When the alarm is triggered the system will provide feedback to the user. Upon disarm, the system will beep four (4) times and flash the LED to indicate the Alarm Trigger Zone.

1 Shock
2 Trunk/Hood
3 Door

Chirp Delete

System ARM/DISARM chirps can be toggled ON or OFF without entering the Feature Bank programming.

  1. Turn the ignition key ON/OFF.
  2. Press and release the valet button three (3) times.

The system will respond with one (1) chirp for ON and two (2) Chirps for OFF. This feature will not affect alarm triggers or programming.

User Programmable LED

System LED notifications can be turned ON or OFF without enteringFeature Bank programming.

  1. Turn the ignition key ON/OFF, ON/OFF.
  2. Press and hold the valet button for five (5) seconds.

The LED will flash one (1) time for ON, two (2) times for OFF. This feature will not affect LED flash during programming.

Remote Programming

The APS510Z includes two (2) programmed remotes. If required, additional remotes can be programmed into the system. RemoteProgramming is located in Feature Bank 1. To enter Remote Auto Programming:

  1. Turn the ignition key on ON.
  2. Press and release the valet button three (3) times. System will chirp and flash the parking lights one (1) time.Press the lock button on each remote. The system will beep one (1)time to indicate the remote has been programmed. Only primary remote functions are auto-programmed. This Includes Lock, Unlock, andTrunk/Start.If using the AUX output control, the remote channel must be manually programmed to the system AUX output. Please see the completeinstallation guide for manual remote programming instruction.

Feature Programming

The APS510Z Feature Bank can be programmed by using the valet button and remote. To enter Feature Bank programming:

  1. Turn the ignition key on ON.
  2. Press and release the valet button three (3) times. System will chirp and flashlights one (1) time for Feature Bank 1, RemoteProgramming.
  3. Cycle ignition key OFF/ON. The system will chirp and flashlights two (2) times for Feature Bank 2.
  4. Press the valet button to cycle features. LED will flash to display the feature number.
  5. Press the lock button to cycle options. The system will chirp to indicate the option number.

To exit the Programming cycle ignition key OFF and wait ten (10) seconds.The System will also automatically exit programming after sixty (60) seconds of no activity.

Dome Delay Programming

This system can be programmed to ignore the vehicle’s theater dimming dome light. This feature will be used when connecting the door trigger input to the dome light circuit for the alarm trigger. Note: Vehicle windows should be open to prevent accidental locking of keys in the vehicle.Start with all doors closed and the vehicle dome light off.

  1. Press Lock, Unlock, Lock, Unlock, Lock, Unlock, Lock. LED will light solid.
  2. Open and close the driver’s door.The system will monitor the dome light circuit. When the dome light turns off the system will set the delay time and add an additional two (2) seconds.

Dome Delay Reset

  1. Key ON/OFF, ON/OFF, ON/OFF.
  2. Press and hold the valet button for five (5) seconds.The system will chirp one (1) time to indicate reset is complete.

Shock Sensor

The shock sensor should be mounted to a solid surface in the center of the vehicle. Once mounted the shock sensor will require adjustment.To increase sensitivity: Turn adjustment dial clockwise.To decrease sensitivity: Turn the adjustment dial counterclockwise.To test sensitivity, strike the vehicle with an open palm. Adjust the dial to provide coverage to as much of the vehicle as possible.

The Feature Bank below can also be programmed using the FlashLogic Weblink.Please visit www.FlashLogic.com for more detail.

Feature Bank 2

Options
1 Chirp 2 Chirp 3 Chirp 4 Chirp 5 Chirp 6 Chirp
I Features I 1 Lock / Unlock Function 50Orns 3.5sec SOOms I., DBL UL DBL L, SOOms UL DBL L, DBL UL SOOms I., 35Orns UL
2 Ignition Lock OFF ON
3 Ignition Unlock OFF Unlock All Unlock Driver
4 Exterior Illumination OFF With Arm With Disarm With Arm & Disarm
5 Auto Relock OFF Auto-Lock Auto-Lock &  Arm
6 Auto Arming OFF Auto Arm Auto-Lock & Arm
7 Notification Sound Both Siren Horn
8 Horn Tuning 16ms 30ms 40ms SOms 10ms
9 Valet Override Method Valet Custom Code
10 Driver Priority Unlock OFF ON
11 Silent Choice OFF From Transmitter OEM Style
12 Park Light/ Trunk Swap NA
13 AUX Ch. 4 Pulse Push & Hold lOsec 20sec Latch On/Off Hold 3/s for 0/P
14 AUX Ch. 5 Pulse Push & Hold lOsec 20sec Latch On/Off Hold 3/s for 0/P
15 Alarm Trigger Length 30sec 45sec 60sec 90sec 120sec
16 Dome Light Delay Timer Off/Program  15sec 30sec 45sec 60sec 120sec
17 Security Profile All On Doors Off Hood/trunk Off All Off All On w/ OEM RS
18 Data Port Protocol ADS DBI

Important Update

The default Data Port Protocol of this system is ADS. If using a FLCAN or other external integration module be sure to choose iDatalink2-Way when flashing.This system will also support DBI. This will require programming Feature Bank 2, Feature 18 to DBI.

Data Protocol Selection

The default data port protocol of this model is ADS (iDatalink 2-Way).This model is capable of detecting the correct data port protocol (ADS or DBI) and automatically configuring Feature Bank 2; Feature 18. To initialize the detection procedure:

  1. Press and hold the valet button.
  2. Cycle the vehicle’s Ignition ON/OFF two (2) times.
  3. Release the valet button.

The system will automatically detect and set the correct data port protocol, ADS or DBI.Note: This feature is only available on module firmware v2.00 or higher.

report this ad

For Complete Installation Guide and Technical SupportPlease visitwww.voxxuniversity.comOr Call1-800-225-6074

REV. B2020 Voxx Electronics. All Rights Reserved.

References

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

, ,