Reboot Welding Machine User Manual

Reboot Welding Machine

Reboot RBA1400 is an intelligent and easy-to-operate welding machine with manual welding mode. It has the characteristics of good welding performance, diversified usage scenarios, and outstanding welding effects. It is highly praised by welding enthusiasts and is also very good for beginners in welding. Friendly and can get started quickly.

Machine Introduction

  1. Current display meterOnly displays the preset current.
  2. Fault lightWhen the welding load is overloaded and the output current of the machine is too large, this light will be on. This situation is normal and the machine can be restored; when there is damage inside the machine, this light will be on. In this case, the machine is abnormal and requires maintenance.
  3. The adjustment knobMMA: Adjusts the current, arc force and hot start; LIFT TIG: Adjusts the current.
  4. MMA and LIFT TIG selectionMMA VRD ON: Turn on this knob, the output no-load voltage is below DC15V, Below the safe voltage, there is protection for human safety, but arc starting will be a little more difficult.MMA VRD OFF: Turn on this knob, the output no-load voltage is DC 60V.LIFT TIG: Turn on this knob, Can be argon arc welding
  5. Function selectionHot start: For MMA mode, it is easier to start arcing when welding with low current, and it is not easy to start the arc during welding.ARC FORCE: For MMA mode, it is easier to start arcing when welding with low current, and it is not easy to start the arc during welding.WELDING CURRENT: MMA and LIFT TIG adjust current.
  6. Electrode diameter selectionChoose different welding wire diameters, corresponding to the corresponding current, no need to adjust the current again
  7. Positive connectionInstall welding holder and grounding clamp.
  8. Negative connectionInstall welding holder and grounding clamp.

Note: RBA1400D is AC 110V OR AC 220V voltage input .

Introduction to the product and configuration list

No.

 Picture Name Qty

Remark

1

 RBA1400 1 Please check the appearance after receiving the machine, and power on to check

2

 Welding holder 1 1.5m 16MM2 cable, 200A Italian welding holder +10-25mm2 European quick plug

3

 Ground clamp 1 1.5m 16MM2 cable, 300A Ground clamp +10-25mm2 European quick plug

4

 Conversion line

1

 Conversion line only suit for 220V to 110V dual-voltage input machines, if not dual- voltage machines no this line included.

5

 Manual

1

 Normally provides manuals in English, if you need other language like French, German, Italian, Spanish, and Russian please contact us to get electronic version documents.

6

 Warranty Card

1

 If you have more questions for consultation, please contact us through the after-sales mailbox on the card.

Simple test for powering on the machine

Reboot RBA1400 welding machine will undergo strict various tests when it leaves the factory to ensure that every welding machine that reaches the user is of high quality, because our machine has to go through tens of thousands of kilometers of long-distance transportation from the factory to the delivery to you. And many times of handling, it is inevitable that some uncontrollable factors will cause some internal components of the machine to become loose or even damaged during the process. We recommend that you perform a power-on inspection as soon as you get the welding machine to ensure that what you receive is qualified product.

Precautions for power-on inspection

  1. Please make sure your power supply voltage is 110V+-15% or 220+-15%. REBOOT RBA1400D supports 110V and 220V input voltage in North America and Japan, and REBOOT RBA1400 supports 220V input voltage in the UK, EU and other regions; if you have a generator power supply, please ensure that the generator is not less than 4000w.
  2. It is recommended to choose 50A circuit breaker protection when your power supply voltage is 110V, and 30A circuit breaker protection when 220V.
  3. For the current machine, please choose the power plug that suits your local electrical law requirements
  4. Extension cord: #12 AWG or larger; 25’ (8m) or shorter.Turn on the power switch of the machine and the fan on the back of the machine rotates, and the digital display on the panel indicates that the power is normal.

Note:

  1. In order to reduce the working temperature of the machine, it is normal for the fan to continue to rotate for a few seconds after the power is turned off.
  2. In the process of high-strength continuous welding, machine protection may occur, and the OC light on the machine panel will be on. After continuous heat dissipation, the machine will return to normal, which is normal.
  3. During the welding process, if you feel that the welding is not good, the spatter is too large, or the arc is broken, please exchange the connection of the welding clamp and the grounding clamp with the machine.

Attached table: Self-examination of abnormal conditions without response when turning on the machine:

  1. The machine’s power switch is not turned on.
  2. The power input voltage is wrong.
  3. The power plug is loose.
  4. The internal circuit is loose (due to long-distance transportation, bumps), you need to open the cover and check the internal connection line.

Technical specifications

TYPE

 RBA1400

RBA1400D

Input power voltage (V)

 1phase AC220V±15%，50/60Hz

1phase AC110V/220V±15%，50/60Hz

Rated input current (A)

 25.1

40/25.1

Rated power capacity (KVA)

 6.4

6.4

Current adjustment range (A)

 30-140

30-120/30-140

Welding thickness (mm)

 >1.0

>1.0

Voltage adjustment range (V)

 23.2-25.6

23.2-25.6

No-load voltage (V)

 60±5

60±5

Rated duty cycle

 60%

60%

Efficiency (%)

 85%

85%

Power factor

 0.7

0.7

Protection class

 IP21S

IP21S

Insulation class

 F

F

Size (mm)

 310*120*280

310*120*280

Weight (Kg)

 5

5

Machine operation guidance

Tips:

  1. Wear a welding helmet fitted with a proper shade of filter to protect your face and eyes when welding or watching;
  2. Wear approved safety glasses. Side shields recommended;
  3. Use protective screens or barriers to protect others from flash and glare; warn others not to watch the arc;
  4. Wear protective clothing made from durable, flame-resistant material(wool and leather) and foot protection;
  5. Use approved ear plugs or ear muffs if noise level is high;
  6. Never wear contact lenses while welding.
MMA mode

If you want to repair some broken fences or fix brackets, you like to use traditional welding rods for operation, you can use REBOOT RBA1400.

  1. Select “MMA” process.
  2. Connect welding holder and ground clamp.
  3. To adjust the current, only the current can be adjusted.

Note:

  1. The welding rod specification supported by REBOOT RBA1400 is below 4.0(5/32in), usually 2.5(3/32in) and 3.2(1/8in). European style generally uses E6013, American style generally uses E7018，and stainless steel generally uses ER308.
  2. It supports welding of 1-8mm(1/64-5/64in) carbon steel and 1 5mm(1/64-7/32in) stainless steel. Aluminum can not be welded. For carbon steel, please use carbon steel electrode. For stainless steel, please use stainless steel electrode.
  3. Connect the ground clamp to clean bare metal. No rust, paint or other coatings, and ensure good electrical conductivity.
  4. The ideal distance between the welding rod and the welding object is 1 2mm(1/64-5/64in), to ensure that the welding rod and the workpiece are in continuous and stable contact. The welding rod should not be too high or pressed too low to avoid arc breaking and adhesion.
  5. It is normal for novices to have adhesion during the welding process, and you can try to friction arc to avoid adhesion.
  6. Suitable for ordinary welding rods, such as 7018, 6013, etc., but not suitable for special welding rods, such as 7010, 7011.

Possible problems

  1. There is no arc, check the ground wire to connect the workpiece to ensure that there is no rust, paint or other coatings on the workpiece.
  2. There is no arc, check the direct distance between the welding rod and the welding object, the ideal distance is 1-2 mm; check whether the welding object has rust or oil stains, it is recommended to polish with sandpaper or a grinder.
  3. During the welding process, the OC fault light is on, and it may be over current protection. You need to stop working for a few minutes, let the machine cool for a period of time, and automatically recover. If the air cools for more than 10 minutes, the machine does not automatically recover, please shut down and restart.
  4. The OC light is on when the machine is turned on, please contact us.
  5. If you have any problems that cannot be solved, please contact us at [email protected].
LIFT TIG mode

REBOOT RBM1300 for thin plates with higher welding process requirements or welding with higher process requirements, especially for stainless steel welding, you can use the LIFT TIG mode, which requires the use of pure argon.

  1. Select “Lift TIG ” process.
  2. How to connect.Remark: TIG welding gun is not included in the package, you need to purchase it separately
  3. Adjust the current, only the current can be adjusted.
  4. WP17V Structure of welding torchNote: Standard accessories package kit not included this tig torch.

Remark:

  1. ceramic nozzle,
  2. tungsten collet,
  3. tungsten collet body,
  4. short back cap,
  5. long back cap.The above structure is a wearing part, please keep it in stock.

Note：

  1. Please connect according to the picture, otherwise it cannot be welded
  2. This machine is not a professional high-frequency arc starting argon arc welding machine, it is only a LIFT TIG contact arc starting or friction starting.
  3. Need to use TIG, wp17v torch, this torch is not included, you need to buy it yourself
  4. Support welding material, carbon steel, stainless steel, alloy steel, aluminum can not be welded.
  5. This welding mode requires the use of tungsten needles, which need to be purchased separately, and the size of the tungsten needle must match the collet and collet body of the welding gun, otherwise it cannot be installed
  6. In this mode, argon welding must be used.

Possible problems

  1. There is no response when starting up, please check the plug connection.
  2. There is no response when booting up, please open the cover and check whether the internal connection wires are loose.
  3. During the welding process, if the time exceeds 3 minutes, over-current protection may occur. You need to stop working for a few minutes, let the machine cool for a period of time, and automatically recover. If the air cools for more than 10 minutes, the machine does not automatically recover, please shut down and restart.
  4. If you have any questions, please contact us at [email protected].
  5. Lift tig is different from professional high-frequency tig. Lift tig needs to be welded after contact with arcing.High-frequency tig does not require contact with arcing. Lift tig is not suitable for spot welding.

Internal diagram of the machine

  1. Digital control panel, the machine is a digital machine, more intelligent.
  2. All-copper main transformer, big power.
  3. 3 high-power large capacitors, the machine is more stable.
  4. Thicker radiator for better heat dissipation.
  5. 4 imported IGBT, stable and powerful current output.
  6. 3 imported rectifier tubes, stable and powerful current output.
  7. Big fan, better heat dissipation effect.
  8. All-copper connecting piece, better conductive effect.

Troubleshooting

PROBLEMS(SYMPTOMS) POSSIBLE CAUSE
PROBLEMS IN STICK WELDING
Excessive spatter
  1. Long arc.
  2. High current.
Craters
  1. Fast movement of the electrode away from piece.
Inclusions
  1. Poor cleanliness or distribution of the Welding passes.
  2. Improper movement of the electrode.
Insufficient penetration
  1. High progression speed.
  2. Welding current too low.
  3. Narrow chamfering.
Sticking
  1. Arc too short.
  2. Current too low.
Porosity 1.  Humidity in electrode.

2.  Long arc.
Cracks
  1. Current too high.
  2. Dirty materials.
  3. Hydrogen in weld (present on electrode coating).
ELECTRICAL FAILURES
Machine fails to come on (Power LED off)
  1. No Input Voltage.
  2. Faulty supply plug or cable.
  3. Internal fuse tripped. Allow time to Auto reset.
Thermal overload (Thermal LED on)
  1. Unit has been operated beyond its capacity rating.
  2. Airflow through machine is restrict- ed or fan has failed.

Welding parameter settings

Welding thickness（㎜） 2 3

4-5
Electrode diameter（ф ㎜） 2 3.2

3.2-4
Welding current (A） 40-65 50-80

100-130

If you are interested in translating professional local languages, please contact us at [email protected], we can pay for it.

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

, , ,