REMINGTON Beard Styler User Manual

REMINGTON Beard Styler

www.remington-products.com.auwww.remington.co.nz

BEARD STYLER IMPORTANT SAFETY INSTRUCTIONSWhen using electrical appliances, basic precautions should always be observed, including the following.READ ALL INSTRUCTIONS BEFORE USINGWARNING: TO REDUCE THE RISK OF BURNS, ELECTROCUTION, AND FIRE OR INJURY TO PERSONSDANGER: As with most electrical appliances, electrical parts are electrically live even when the switch is off.

  • This appliance should not be used by children or other persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Keep the appliance and the USB charging cable away from the edge of the table or countertops and out of reach of children and persons with reduced physical, sensory or mental capabilities.
  • This appliance is not a toy. Children shall be supervised to ensure they do not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
  • Never operate this appliance if it is damaged, not working correctly, or has a broken trimming unit as injury may occur.
  • Never operate this appliance if the USB charging cable has been damaged or dropped into water.
  • Use this appliance only for its intended use as described in this manual.
  • Do not use attachments not recommended by Remington.
  • Do not use outdoors or where aerosol (spray) products are being used, or oxygen is being administered.
  • This appliance should never be left unattended when plugged into a power outlet, except when charging.
  • Remove appliance from USB port immediately after charging.
  • Do not plug or unplug the appliance with wet hands.
  • Unplug and switch off this appliance before cleaning it.
  • Do not wrap the USB charging cable around the appliance.
  • Keep the USB charging cable away from heated surfaces.
  • Always store the USB charging cable in a moisture-free location.
  • Do not use on people who are asleep.
  • For household use only.
  • This appliance is supplied with a USB charging cable for charging via standard USB ports, with a power requirement of 5.0V DC 500mA input.

Remington strongly recommends that an approved Safety Switch (residual current device) be installed to protect all bathroom power outlets. Ask an electrical contractor for advice.

NOSE & EAR TRIMMER IMPORTANT SAFETY INSTRUCTIONS

  • To prevent accidents keep the appliance away from your eyelashes as well as clothes, brushes, and wire.
  • Always remember to turn on the trimmer before you insert it into your nose or ear to avoid painfully snagging hairs.
  • Never insert the trimmer more than 6mm (1/4″) into your nose or ear. Foreign objects should not come into contact with your eardrum.
  • This appliance should not be used by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
  • Keep the appliance and the power cord away from the edge of the table or countertops and out of reach of children and persons with reduced physical, sensory or mental capabilities.
  • Children shall not play with the appliance.
  • Cleaning and user maintenance shall not be made by children withoutsupervision.
  • Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by Remington.
  • Do not use it on people who are asleep.
  • Never drop or insert any object into any opening of this appliance.
  • Do not use the trimmers with damaged or broken cutters, as injury may occur.
  • Always store the appliances in a moisture-free area. Do not store it in temperatures exceeding 60°C (140°F).
  • Do not disassemble the detail trimmer cutter assembly.
  • Do not submerge the units in water as damage will occur.
  • This appliance is for household use only.SAVE THESE INSTRUCTIONS

MB4123PAU BEARD STYLER FACIAL GROOMING KIT USE AND CARE MANUALThank you for purchasing your new Remington® Beard Styler. Inside this manual, you will find instructions on using and caring for your Beard Trimmer and Nose & Ear Trimmer.

KEY PARTS

Beard Trimmer

  1. 30mm Trimmer
  2. Adjustable Beard Comb (2-18mm)
  3. On/Off Switch
  4. Charging Indicator LightAlso Includes:• Power Adaptor with USB cable• Cleaning BrushNose & Ear Trimmer
  5. Nose & Ear Trimmer Head Attachment
  6. On/Off Switch
  7. Battery CompartmentAlso Includes:• 1 x AA battery

ABOUT YOUR BEARD TRIMMER

AFTER EACH USEWe recommend that you clean your groomer after each use.

  • Brush any accumulated hairs from the groomer.
  • The easiest and most hygienic way to clean the groomer is by detaching the head from the groomer’s body and rinsing the head with warm water.
  • The groomer’s body should not be rinsed.
  • Place one or two drops of cutter oil or sewing machine oil on the blades.
  • Turn the groomer on to distribute the oil evenly, wipe off any excess oil.

ATTACHING THE GROOMING ATTACHMENTS

  • To attach the adjustable comb to the 30mm trimmer head, line the comb rails up with the trimmer head and slide onto the groomer until firmly secured.

Before You Begin

  • Comb facial hair with a fine comb before you start trimming.
  • Hair should be dry and without any waxes or lotions before using the groomer.

To Thin And Taper The Beard/Moustache

  • Place the adjustable comb on the trimmer blade, select the desired length and switch on.
  • Start trimming under the chin, following the jawbone line. Work towards the ear and upper beard line using an upward motion.

To Trim Edge Of Beard Or Moustache

  • · Hold the groomer with the cutting blade facing you, perpendicular to your skin.
  • · Start with the edge of the beard/moustache line, and with the cutting bladesresting lightly against your skin, use slow movements to create a beard/moustache line.

To Trim Sideburns

  • Hold the groomer with the cutting blade facing you.
  • Select the desired length on the adjustable comb.
  • Move the groomer along the comb to cut the hairs. Use light pressure and well-controlled movements to trim hair.

Trimming The Nape Of Your NeckUse your fingers to lift the hair at the base of your head up off the neck. Your index finger should be covering the roots of the hairs you are lifting to prevent accidental removal by trimmer.Using your other hand, hold the trimmer to the base of your neck with the cutting unit facing up, and move the trimmer up the length of the neck until it touches your finger covering the hair roots at the base of your head.Be sure to move the unit slowly when performing this operation and to keep the hair roots at the base of your head out of the way of the trimmer.

TIPS FOR BEST RESULTS

  • Beard, moustache and sideburn hairs should be dry.
  • Avoid using lotions before using your groomer.
  • Before trimming beards, comb your hair in the direction that it growsso that the hairs are at their maximum height and facing in the same direction.
  • Since all hairs do not grow in the same direction, you may want to try different trimming methods (i.e. upwards, downwards or across). Practice is best for optimum results.Note: Use slow light pressure. Too much pressure may trim off more hair than desired.

CLEANING AND MAINTENANCE

  •  To ensure the long-lasting performance of the trimmer, clean the bladesand unit after each use.
  •  Ensure the appliance is switched off and unplugged from the mains.
  • Do not use harsh or abrasive cleaners on the unit or blades.
  • This product has washable blades. Ensure the blades are detached from the trimmer before washing the blades.
  • Wash the blades under a running tap to remove any hair clippings.
  • After rinsing under a tap ensure the blades are dry.
  • Do not rinse while the product is connected to the mains.
  • Please note the main body of the trimmer is not washable and should be kept away from water.
  • After each use, it is recommended to clean hair from blades either by using the cleaning brush or by rinsing the blades under running water.
  • When rinsing the blades it is necessary to lubricate them once dry. With the unit turned off apply 3 drops of oil to the moving blade facing up, one drop on each end and one in the middle, then switch the unit on for a few seconds to distribute the oil, then turn the unit off and wipe off excess oil.

Note: Do not disassemble the blades.ENVIRONMENTAL PROTECTIONTo avoid environmental and health problems due to hazardous substances in electrical and electronic goods, appliances marked with this symbol must not be disposed of with unsorted municipal waste, but recovered, reused, or recycled.BATTERY DISPOSALNote: The battery is not intended to be removed or replaced under normal use. The only time the battery should be removed or the unit opened or disassembled, is at the end of the product’s useful life before it is discarded.

  • The MB4123PAU groomer contains a nickel-metal hydride battery. Once the groomer has reached the end of its life, to ensure proper disposal of the product, please take the appliance to a recycling center, where the internal rechargeable battery should be removed by a professional and recycled separately.
  • For more information about recycling electrical and battery-operated appliances, please contact your local council office or your household waste disposal service.

Caution: Do not put in the fire or mutilate your batteries when disposing of as they may burst and release toxic materials. Do not short circuit as it may cause burns.

ABOUT YOUR NOSE & EAR TRIMMER

SPECIFICATIONS – PG018Power System – Cordless (Battery Operated)Voltage Type –  1x AA Battery

INSERTING THE BATTERYYour Remington® nose & ear trimmer is powered by one “AA” alkaline battery (battery included).

  1. To open the battery compartment, turn the base of the unit approximately 1cm clockwise (to the right) and pull it off.
  2. Insert the battery into the unit, positive end first.
  3. Replace the base and turn it 1cm anti-clockwise (to the left) to lock it in place.

Battery Cautions:

  • Using non-alkaline batteries will impair the unit’s operating performance.
  • The battery should not be left in the unit if it is not in use for long periods.
  • To prevent battery corrosion, the unit should be stored in a dry environment.
  • Dead batteries should be removed immediately and disposed of properly.
  • Do not use rechargeable batteries with this appliance. The lower voltage in rechargeable batteries impairs the performance of the cutting unit.

HOW TO USE

To Remove Hair From The Nose:

  1. Select the nose & ear trimmer.
  2. Turn the trimmer on.
  3. Insert the trimmer’s cutting unit gently into the nostril.
  4. Rotate the trimmer in a circular motion around the opening of the nostril.
  5. For best cutting efficiency, gently move the trimmer in and out of the nostril as you rotate the trimmer.
  6. Do not insert the trimmer more than 6mm into your nostril.

Note: Always remember to turn on the trimmer before you insert it into your nose or ear to avoid painfully snagging hairs.

To Remove Hair From The Ear

  1. Select the nose & ear trimmer.
  2. Turn the trimmer on.
  3. Insert the trimmer’s cutting unit gently into the outer ear canal opening.
  4. Gently rotate the trimmer in a circular motion.
  5. To trim hairs protruding from the surface of the area surrounding the outer ear canal, guide the trimmer around the edge of the ear.
  6. Avoid inserting the trimmer more than 6mm into your ear canal.

Note: Do not apply pressure as this damages the trimmer and may cause skin injury.

CLEANING & MAINTENANCE

Your nose & ear trimmer is designed to give you years of comfortable use. To ensure you get optimal performance from your trimmer, follow these simple cleaning and lubricating tips:• After each use, brush or blow accumulated hair from the cutting unit.Rinsing Your Trimmer:• The heads of your trimmer is washable and can be rinsed with cool orwarm water. Simply twist the attachment head 1cm anticlockwise (to the left), remove the head and rinse it under the tapCaution: Do not use hot water. Do not allow water into the body of the handpiece.• Afterward, shake excess water from the cutter head. Be sure to be careful when handling the nose trimmer blades as they are sharp.• Replace the head in the same position as it was removed, turning it 1cm clockwise (to the right) until it locks into place.Lubricating The Cutters:

  • After rinsing the attachment head, apply a drop or two of lubricating oil or sewing machine oil to the blades.
  • Don’t apply too much oil, or it may spray.
  • Finally, point the trimmer down and away from you, and turn it on. This spreads the oil evenly and expels any excess.

This product is not suitable for use in the bath or shower. This product conforms to radio frequency interference requirements Any product purchased and used commercially carries a limited 90 Day Warranty.

Spectrum Brands Australia Pty Ltd and Spectrum Brands New Zealand LimitedWARRANTY AGAINST DEFECTS

In this warranty:Australian Consumer Law means the Australian consumer law set out in Schedule 2 to the Competition and Consumer Act 2010;CGA means the New Zealand Consumer Guarantees Act 1993;Goods mean the product or equipment which was accompanied by this warranty and purchased in Australia or New Zealand, as the case may be;Manufacturer, We or us means:1. for Goods purchased in Australia, Spectrum Brands Australia Pty Ltd ACN, 007 070 573; or2. for Goods purchased in New Zealand, Spectrum Brands New Zealand Limited, as the case may be, contact details as set out at the end of this warranty;

Supplier means the authorized distributor or retailer of the Goods that sold you the Goods in Australia or in New Zealand; andYou mean you, the original end-user purchaser of the Goods.

  1. Our goods come with guarantees that cannot be excluded under the AustralianConsumer Law, or the CGA. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
  2. The benefits provided by this Warranty are in addition to all other rights and remedies in respect of the Goods which the consumer has under either the Australian Consumer Law or the CGA. The original purchaser of the Goods is provided with the following Warranty subject to the Warranty Conditions:
  3.  We warrant the Goods for all parts defective in workmanship or materials for the period of two (2) years from the date of purchase (Warranty Period). If the Goods prove defective within the Warranty Period by reason of improper workmanship or material, we may, at our own discretion, repair or replace the Goods without charge.Warranty Conditions
  4. The Goods must be used in accordance with the manufacturer’s instructions. This Warranty does not apply should the defect in or failure of the Goods be attributable to misuse, abuse, accident, or non-observance of manufacturer’s instructions on the part of the user. As far as the law permits, the manufacturer does not accept liability for any direct or consequential loss, damage, or other expense caused by or arising out of any failure to use the Goods in accordance with the manufacturer’s instructions.
  5. Consumable parts (such as shaver heads, cutters, and foils) of the Goods are included under this Warranty only where there is a defect in workmanship or materials used.
  6. The warranty granted under clause 3 is limited to repair or replacement only.
  7. Any parts of the Goods replaced during repairs or any product replaced remain the property of the manufacturer. In the event of the Goods being replaced during the Warranty Period, the warranty on the replacement Goods will expire on the same date as for the Warranty Period on the original Goods which are replaced.
  8. In order to claim under the warranty granted under clause 3 you must: (a) Retain this warranty with your receipt/proof of purchase; and (b) Return the Goods to us at the relevant address below or to the Supplier by prepaid freight within the Warranty Period accompanied with (i) the legible and unmodified original proof of purchase, which clearly indicates the name and address of the Supplier, the date and place of purchase, the product name or other product serial number and (ii) this warranty.
  9. This warranty is immediately void if: (a) Any serial number or appliance plate is removed or defaced; (b) The Goods have been serviced or otherwise repaired by a person not authorized to do so by us or where non-approved replaced parts are used.
  10. The Goods are designed for domestic use only. A limited 90-day Warranty applies to any industrial or commercial use of the Goods. The Goods must be connected to the electrical voltage requirements as specified in the rating label located on the Goods.
  11. This warranty does not cover the cost of claiming under the warranty or transport of the Goods to and from the Supplier or us.
  12. This warranty is only valid and enforceable in Australia against Spectrum Brands Australia Pty Ltd and in New Zealand against Spectrum Brands New Zealand Limited.

Contact us or the Supplier for further details.Spectrum Brands Australia Pty LtdLocked Bag 3004Braeside, VIC 3195AUSTRALIACustomer service in Australia: 1800 623 118E-mail: [email protected]Website: www.remington-products.com.au

Spectrum Brands New Zealand LimitedPO Box 9817Newmarket, Auckland 1149NEW ZEALANDCustomer service in New Zealand: 0800 736 776E-mail: [email protected]Website: www.remington.co.nz

References

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

, ,