REMINGTON Style Series Aqua Foil Shaver F6000 User Guide

REMINGTON Style Series Aqua Foil Shaver F6000 User Guide

Overview

Thank you for buying your new Remington® product. Please read these instructions carefully and keep them safe. Remove all packaging before use.

IMPORTANT SAFEGUARDS

  • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been supervised/instructed and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be done by children unless they are older than 8 and supervised. Keep the appliance and cable out of reach of children under 8 years. Suitable for use in a bath or shower.
  • Do not use the product with a damaged cord.
  • The battery in this device is not replaceable.
  • Do not use the appliance if it is damaged or malfunctions.
  • Do not use attachments other than those we supply.
  • This appliance should never be left unattended when plugged into a power outlet, except when charging.
  • Keep the power plug and cord away from heated surfaces.
  • Do not plug or unplug the appliance with wet hands.
  • Do not twist or kink the cable, or wrap it round the appliance.
  • This appliance is not intended for commercial or salon use.

PARTS

  1. On/off switch
  2. Foil screens
  3. Cutter assembly
  4. Charging indicator lights
  5. Hairpocket
  6. Power port
  7. Pop-up trimmer
  8. Head release buttons
  9. Head lock button
  10. Stubble head guard

Not shown:

  • USB charging cable
  • Cleaning brush

GETTING STARTED

CHARGING YOUR APPLIANCE 

  1. Ensure the product is switched off.
  2. Connect the product to the USB cable and then to the USB end of the cable to a powered USB port.

CHARGING INDICATOR LIGHTS

Charge Level

Lights

Charging The lights will come on one after the other then go off in a repeating pattern.
Fully Charged Both lights will come on for 5 minutes then go out.
Low charge/charging required The bottom light will flash rapidly.
Battery capacity 60% or higher Both lights will come on.
Battery capacity 60% or lower The bottom light will come on.
  • Run time from fully charged is up to 60 mins.
  • Charge time from empty is 90 mins.
  • Note: To preserve the life of your batteries, let them run out every 6 months then fully charge.

INSTRUCTIONS FOR USE

It is recommended that you use your new shaver daily for up to two weeks to allow time for your beard and skin to become accustomed to the new shaving system.

  • Make sure your shaver is properly charged.
  • Switch the shaver on by pressing the on/off switch.
SHAVING
  • Stretch the skin with your free hand so the hairs stand upright.
  • Hold the shaving head so that the foils touch your face.
  • Use short linear strokes.
TRIMMING
  • Slide up the trimmer release button to activate the trimmer.
  • Hold the trimmer at a right angle to your skin.
  • To retract the trimmer, push the top rear of the trimmer down until it locks under the trimmer release button.

STUBBLE LOOKFit the stubble head guard to your shaver for a 3-day stubble look.

HEAD LOCKNormally, the head pivots freely but its movement can be restricted by sliding the head lock button to the locked position.

TIPS FOR BEST RESULTS

  • Always hold the shaver at right angles to the skin so that all foils are touching the skin with equal pressure.
  • Use moderate to slow stroking movements. The use of short linear motions in stubborn areas may obtain a closer shave, especially along the neck and chin line.
  • DO NOT press hard against the skin in order to avoid irritation and damage to the foil heads.

CLEANING AND MAINTENANCE

  • To ensure long lasting performance clean after each use.
  • Ensure the appliance is switched off and unplugged from the mains.
  • The easiest and most hygienic way to clean the appliance is by rinsing the appliance head after use with warm water.

DRY CLEANING 

  • Press the head release buttons and and pull the head upwards (Fig E).
  • Gently tap out the excess hair shavings and use a cleaning brush to clean out the hair pocket if necessary (Fig F).
  • Note: Do not use a brush to clean the shaving foils.
  • Replace the head assembly

WASHABLE CLEANING 

  • Press the head release buttons and and pull the head upwards (Fig E).
  • Do not use the brush to clean the foils but blow the shavings out or rinse in running water (Fig G).
  • Use the cleaning brush to sweep any loose hairs from the cutter and trimmer. Rinse in running water.
  • Replace the head assembly.
  • Lubricate the teeth of the trimmer every six weeks with a drop of sewing machine oil.

REPLACING THE FOILS AND CUTTERS 

  • To ensure continued high quality performance from your shaver, we recommend the foils and cutters are replaced regularly Signs that your foil/s and cutter/s need replacing:
  • Irritation: as foils get worn, you may experience skin irritation.
  • Pulling: as the cutters wear, your shave may not feel as close and you may feel the cutter pulling your hair.
  • Wear through: you may notice that the cutters have worn through the foils.

TO REPLACE THE FOIL/CUTTERS 

  • Press the head release buttons and and pull the head upwards.
  • Fit the new head assembly over the hair pocket and press down to click into place.

BATTERY REMOVAL

  • The battery must be removed from the appliance before it is scrapped.
  • The appliance must be disconnected from the supply mains when removing the battery.
  1. Pry off the two decorative side panels.
  2. Unscrew one screw from the bottom of the shaver and remove the bottom panel.
  3. Remove the foil assembly and unscrew the 4 screws underneath it.
  4. Remove the two E-rings one on each side of the head then lift off the upper head assembly.
  5. Unscrew the 2 screws below the upper head assemly then lift the rest of the head off the body.
  6. Pry off the upper decorative panel to expose 2 screws. Remove the screws.
  7. Remove the front panel to expose 4 screws. Remove the 4 screws then remove the back housing.
  8. Lift out the battery and printed circuit board assembly.
  9. Disconnect he battery from the circuit board.
  10. Dispose of the battery safely.

RECYCLING

 To avoid environmental and health problems due to hazardous substances, appliances and rechargeable and non-rechargeable batteries marked with one of these symbols must not be disposed of with unsorted municipal waste. Always dispose of electrical and electronic products and, where applicable, rechargeable and non-rechargeable batteries, at an appropriate official recycling/ collection point.

 

report this ad

References

[xyz-ips snippet=”download-snippet”]


Posted

in

by