ROCKVILLE D-4,D-16 Wall Mount Speakers Owner’s Manual

Table of Contents

ROCKVILLE D-4,D-16 Wall Mount Speakers Owner’s Manual

OWNER’S MANUAL

Rockville 04-8 and 04-16 are 8 ohm and 16 ohm commercial wall mount speakers. They are a great choice for any restaurant, office, school, retail store, or other commercial application.These speakers will sound great for all your PA announcements and background music. Please read this guide carefully for proper use of your 04-8 or 04-16 speakers.Should you need assistance, please call our technical help line at 1-646-758-0144, Monday through Friday, 9am to 5pm EST.

Functions

Metal grill
Full range speaker
European-style terminal block (euroblock)

Connecting the Speakers

These speakers are passive and thus require an amplifier or receiver to give them power. They can be connected to any 4 or 8 ohm amplifier. If your speakers are relatively close to the signal source (50 feet or less), 16 gauge wire can be used. For longer distances, 12 or 14 gauge wire is recommended. Be sure to observe proper polarity by ensuring that the wire from the positive speaker terminal is connected to the red or positive terminal of the signal source and that the wire from the negative speaker terminal is connected to the black or negative terminal of the signal source.

Features/Specifications

Weather resistant with rugged ABS cabinet is perfect for outdoor patio or indoor use
Curved cabinet design for better sound coverage with an 80° x 120° dispersion
Dual swivel mounting bracket supports vertical 90° swivel and horizontal 100° swivel
Polypropylene Cone
Rubber Surround
(2) 4” Woofers
1″ Kapton Voice Coil
r· Soft Silk Dome Tweeter
9. 75 oz. Ferrite Magnets
Detachable Euro-Block terminals with quick disconnect
Built in 12dB/Octave crossover with dynamic speaker protector
Crossover details: 2nd order/2500Hz rolloff
Impedance: Available in 8 ohm or 16 ohm
Frequency Response: 55Hz – 20KHz
Sensitivity: 1w/1 m
Available in black or white
Dimensions in inches: 12.05′ x 6.6″ x 8.T
Weight: 6.4 Lbs

RockvilleD4 WALL INSTALLATION PROCESS

Go to vimeo.com/560964339 or scan the OR code and watch a short video that shows you how to install and adjust the D4’s wall mount bracket.Should you need further assistance, please call our technical help line at 1-646-758-0144, Monday through Thursday, 9am to 10pm EST, and Fridays, 9:ooam to 3pm EST

Using the moonting bracket as a template, mark the mounting screw locationsOrill pilot holes for the screws. Besure to use the proper drill bit size !or the an chol’s. We recommend using a 7/3Tdrillbit.Insert one of the included anchors into each hole. 1-.10 not mount the bracXet yetSlide the mounting bracket into the speaker bracket as shown above. Make sure the stamped side of the bracket, as well as that of the mount, is facing down.lnsert the hex bolt sleeve.

Align the bracket screw hole with that of the mount and the hex bolt sleeve. Slide the locking washer onto the hex bolt and insert the bolt assembly into the hole.

Attach the nut onto the hex bolt and hand tighten, but do not fully tighten.

Place the entire bracket assembly against the wall and align the mounting bracket’s screw holes with the anchors. Tilt the wall bracket down in order to expose the two top holes. Insert one screw in each hole. We recommend using a power tool in order to firmly drive the screws into the wall anchors.

Tilt the wall bracket up to expose the two bottom holes. Insert one screw in each hole and firmly drive the screws into the wall anchors.Prior to mounting the speaker to the wall bracket, set the desired angle at which your speaker will be mounted.To set the bracket position, hold the nut on the stamped side with a pair of pliers or an adjustable wrench and use the Allen wrench to tighten the hex bolt until it feels solid. Do not be afraid to overtighten.Put the speaker in place and insert the bottom tightening screw first. Do not fully tighten.Adjust the speaker to the desired angle.