HTS56 5.1 Channel Home Theater Audio System with LED Light Effects
COMPONENT CONNECTIONS1. OPTICAL AUDIO INPUT: Use the optical port to input the sound signal from any 5.1 channel optical output enabled source such as TVs, Digital set-top boxes, game consoles, DVD players, Blu-ray players, CD players, etc. Please note: If you are having issues with sound output, follow these steps:a. Set your TV’s sound output to external speakers. b. Go into your TV’s audio settings and make sure to deactivate Dolby Pro-Logic,Dolby ATMOS, etc. and select PCM format. 2. RCA AUX AUDIO INPUT: Use the RCA Auxillary jacks to connect computers, cellphones, or any other external sound source with a 3.5mm output. You will need an RCA to 3.5mm Y cable. 3. DVD AUDIO INPUT: Use these RCA jacks to input the sound signal from any 5.1 channel output enabled source such as a TV, Digital set-top boxes, game consoles, DVD players, Blu-ray players, CD players, etc.OPTICAL AUDIO INPUT1235
POSITIONING THE SPEAKERS1. Most people place the subwoofer in the front of the room, near the sound input source, for ease of connection. But since bass frequencies are omnidirectional the subwoofer can be placed anywhere. Try placing it near a wall or a corner for increased bass.2. The center channel speaker should be place directly in front of the listening position, above or below the sound input source. If possible, tilt it as necessary to direct the sound to ear level.3. Mount the front speakers on the wall, directly to the left and right of the center channel speaker. Angle them towards the listening postion. Preferably, the tweeters should be at ear level.4. Mount the satellite speakers on the wall, slightly behind the listening position, about 1 to 2 feet above ear level. If side placement isn’t possible place them to the rear of the listening position and angle them forward.SUB0°
20° 30°
20° 30°
90° 110°6
90° 110°
MOUNTING INSTRUCTIONSBefore you begin please make sure you have the proper tools and necessary accessories. For this installation you will need the following items: · mounting brackets and screws (included) · wall hooks (optional, not included) · speaker cable (included) · drill · Phillips screw driverMake sure you have all the necessary screws and brackets. There should be five brackets and one bag of screws. If any of these items are missing, please contact Rockville.Using two screws, secure one bracket to the back of each speaker you wish to mount. If you are mounting the speakers horizontally, you will need to use two brackets for each speaker.Now mark on the wall the place where you will be mounting your speakers. Use the diagram from the POSITIONING THE SPEAKERS section to determine the best location. Both front speakers should be at the same height; the same goes for the satellite units. Remember to keep speakers at least two feet away from corners, and make sure you have enough wire to reach the mounting location.You can use a screw or a mounting hook to hang the speaker. Use a screw with a drywall insert or drive it into a wall stud to ensure that it is securely fastened to the wall. Use a stud finder to locate the stud and to make sure that there are no wires or cable lines located in that area. Once the mounting hooks or screws are in place, you are ready to begin mounting. Be sure to wire each speaker before mounting it to the wall.7
REMOTE CONTROL FUNCTIONS: Power/Standby INPUT: Switch between input modes: USB/FM/AUX/DVD/OPT/BT MUTE: Mute all output 5.1/2.1: Channel mode select SLEEP: set unit to sleep mode LED LIGHT: Set subwoofer LED light mode/turnoff speaker LEDs SAVE: Save stations to unit memory TUNE +/ : Manually tune FM stations: Play/Pause in USB/SD/BT modes AUTO: Automatic station search CH / : Previous FM station/previous track (USB/SD) CH +/ : Next FM station/next track (USB/SD) FL +/ : Front left speaker volume control FR +/ : Front right speaker volume control SW +/: Subwoofer volume level CEN +/ : Center speaker volume control VOL +/: Master volume control SL +/ : Front left speaker volume control SR +/ : Front right speaker volume control 0 9: Number pad used to direct select trackswhen in USB/SD mode REPEAT: Repeat one song/repeat all songs/shuffle RESET: Reset volume level MIC +/ (EQ +/- : When a mics are connected, these buttons will control the mic volume. In USB/SD mode, they will allow you to navigate the 5 preset EQ curves. Please note: connecting mics will override the EQ +/- function. ECHO +/ (DISP +/-): When a mics are connected, these buttons will control the echo effect. If there are no mics connected, they will control the display brightness. Please note: connecting mics will override the DISP +/- function.8
FRONT PANEL1
2
7
3
4
8
9
5 6
10 9
REAR PANEL1 2 10
OPTICAL AUDIO INPUT34 5 6 7 8 9 10 11 12
FRONT PANEL1. Input: Use this key to switch between AUX, SD, USB, OPTICAL, and FM modes. 2. Standby: While in AUX/SD/USB/OPT/FM modes, press and hold for 3 seconds to enterstandby. 3. Master volume: turn the knob left or right to increase or decrease the system’s volume. 4. CH / : Previous FM station/previous track in USB/SD mode. 5. SD card reader 6. USB port 7. Pro-Logic: Pro-logic function key 8. CH+/ : Next FM station/next track in USB/SD mode. 9. AUTO/ : Press and hold for 5 seconds for automatic station search /Play-pausefunction in USB/SD mode. 10. ¼ MIC inputs: Use these jacks to connect up to 2 microphones for Karaoke.REAR PANEL1. Power input 2. Power switch 3. Optical audio input 4. FM antenna 5. RCA AUX in 6. Front L / R RCA DVD audio input 7. Center /subwoofer RCA DVD audio input 8. Rear L / R RCA DVD audio input 9. Center RCA audio output 10. Front L / R RCA audio output 11. Rear L / R RCA audio output 12. LED power output11
BLUETOOTHTo connect your iPod, iPhone, MP3 player, Android phone or any other Bluetooth capable device follow the steps listed below. 1. Make sure the unit is plugged in and the power switch is in the ON position.2. Press the INPUT button on the remote control or push the INPUT button on the unit until the digital read out shows “BT”.3. Turn on the Bluetooth feature on your device and ensure that it is in “discoverable” mode. Search for “Rockville HTS56” on your list of available devices and select it.4. If your device requires a password, please use “0000”.FM RADIOFor FM radio follow the steps listed below. 1. Make sure the unit is plugged in and the power switch is in the ON position. Be sure toconnect the included FM antenna.2. Press the INPUT button on the remote control or push the INPUT button on the unit until the digital read out shows numbers.3. To automatically save stations: · Press and hold the AUTO button for 3 seconds. The unit will begin to automatically search and save any available stations.4. To manually save stations:· Use the TUNE +/TUNE – buttons to find a station you like and that is coming in clearly.· Press the SAVE button. CHAN will start flashing on the screen. Use the CH-/CH+ buttons to select the channel number you’d like to program for that station.· Press the SAVE button again. This will set the channel & the message “good” will be displayed.5. Use the CH-/CH+ buttons to navigate through saved stations or use the TUNE +/TUNE buttons to manually find a station.USB/SDFor USB/SD playback, follow the steps listed below. 1. Make sure the unit is plugged in and the power switch is in the ON position.2. Press the INPUT button on the remote control or push the INPUT button on the unit until the digital read out shows “USB” or “SD”.3. Plug in your SD card or USB flash drive. The unit will automatically read the files and begin playing music.OPTICAL INPUTFor audio via optical input, follow the steps listed below. 1. Make sure the unit is plugged in and the power switch is in the ON position.2. Plug in your optical audio cable into the optical audio output port of the sound source. Plug the other end to the optical audio input port of HTS56.3. Press the INPUT button on the remote control or push the INPUT button on the unit until the digital read out shows “OP”.4. Set your TV’s sound output to external speakers.Please note: If you are having issues with sound output, go into your TV’s audio settings and make sure to deactivate Dolby Pro-Logic, Dolby ATMOS, etc. and select PCM format.12
MIC INPUTTo use the system for karaoke connect any microphone via either one of the ¼ inputs located on the front of the unit. While the MICs are connected, you can control the mic volume by pressing the MIC- or MIC+ buttons on the remote. Additionally, you can control the mic echo effect settings by pressing the ECHO- or ECHO+ buttons on the remote.
TROUBLESHOOTING
PROBLEM
SOLUTION
No power No soundvimeo.com/473203709
Make sure the unit is plugged in and the power switch is in the ON position.1. Make sure you’ve selected the proper source. 2. Make sure all speakers are properly connected. 3. Check individual speaker volume controls as well as the master volume. 4. Check the input source’s volume settings. 5. Make sure you’ve selected external speakers in your TV’s sound ouput settings. 6. Deactivate Dolby Pro-Logic, Dolby ATMOS, etc. andselect PCM in your TV’s sound format settings. 7. Check all connections between the receiver and the input source. Go to the URL or scan the qr code on the left for helpful information.
No sound from mics
1. Make sure the mics are turned on and properly connected. 2. Adjust the mic volume on the remote control. 3. Check individual speaker volume controls as well as the master volume.
Bluetooth pairing fails
1. Check to see that both devices are turned on and that your Bluetooth device is discoverable.2. Turn both devices off and then on again.3. Make sure you’ve selected the proper source.4. Make sure that the Bluetooth device is within 5 feet of the unit.5. Move both devices away from other Bluetooth devices, microwaves, wireless routers, and other electronics.6. Make sure that the unit is not paired to a previously paired device.
No SD or USB memory device playback
1. Make sure you’ve selected the proper source, USB/SD (see page 11).2. Make sure that the audio files are in the proper format (see page 14).3. Make sure you are not exceeding the SD card andUSB drive size limitations (see page 14).4. Make sure that the SD card or USB drive is properly plugged in.5. Check the SD card or USB drive for damage.
Poor or no radio reception 1. Make sure antenna cables are properly connected and above the unit.
13
FEATURES/SPECIFICATIONS· HTS56 5.1 Channel Home Theater System with LED Light Effects · Plug and play system with everything you need right out of the box · 1000 Watts Peak Power · 500 Watts Program Power · 250 Watts Continuous RMS Power · 8 Subwoofer with built-in receiver · 1 x 3 Center Channel Speaker · 2 x 3 Full Range Front Channel Speakers · 2 x 3 Full Range Rear Channel Speakers · Top-quality MDF wood cabinets with plastic front panels · Built-in FM receiver with amazing reception · Digital display · 5 preset EQ curves · You can independently control the volume of each speaker and the subwoofer · Bluetooth v2.1 · USB input (max file size: 16Gb) · SD input (Minimum card capacity is 512Mb, max file size: 16Gb) · Acceptable file formats: MP3, WMA, APE, FLAC, and WAV. · 2 ¼ MIC inputs with echo function for karaoke · 5 RCA Audio outputs · 6 RCA DVD Audio inputs · 2 RCA AUX inputs · Optical audio input · FM antenna input · Full function remote · The subwoofer unit has 4 LED lighting modes: (blink to the beat, solid on, spectrum EQanalyzer, off) and selectable with 7 colors or multi-color mode. · Cable Length: Front L/F: 12Ft, Rear L/R: 23Ft, Center: 10Ft · Frequency Response: 20Hz 20KHz · Certification: CE and RoHS Compliant · Amplifier: Class AB, very efficient amplifier with top components! · Signal to noise ratio: 70dB (Maximum output with THD+1<1%) · System Impedance: 8 driver: 8 Ohm /3 driver: 4 Ohm · Max SPL: 106 dB @ 1w/1m · THD: 1% · Input voltage: 120V/60Hz · Subwoofer Dimensions in Inches: (W*D*H) 9.25 x 13.19 x 14.57 · Center Speaker Dimensions in Inches: (W*D*H) 3.94 x 4.13 x 14.57 · Front L/R Satellite Speaker Dimensions in Inches: (W*D*H) 3.94 x 4.13 x 14.57 · Rear L/R Satellite Speaker Dimensions in Inches: (W*D*H) 3.94 x 4.13 x 9.25 · Shipping Dimensions in Inches: (W*D*H) 18.58 x 12.99 x 21.34 · Net Weight: 26.47 LBS · Shipping Weight: 28.68 LBS14
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATIONResponsible party name: Rockville Address: 600 Bayview Ave,Entrance A, Inwood, NY 11096 Hereby declares that the product Rockville HTS56 complete powered home theater system complies with FCC rules as mentioned in the following paragraph: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:· Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment to an outlet on a circuit different from that to which thereceiver is connected.· Consult the dealer or an experienced radio/TV technician for help.15
RockvilleAudio.com© 2020 ROCKVILLE // Features and specifications are subject to change and or improvement without notice.
References
[xyz-ips snippet=”download-snippet”]