ROTEL DAB FM Stereo Tuner Owner’s Manual
Rotel products are designed to comply with international directives on the Restriction of Hazardous Substances (RoHS) in electrical and electronic equipment and the disposal of Waste Electrical and Electronic Equipment (WEEE). The crossed wheelie bin symbol indicates compliance and that the products must be appropriately recycled or processed in accordance with these directives.
This symbol means that this unit is double insulated. An earth connection is not required.
ANTENNA GROUNDING ACCORDING TO NATIONAL ELECTRICAL CODE INSTRUCTIONSSECTION 810: “RADIO AND TELEVISION EQUIPMENT”
Notice
The rear RS232 connection should be handled by authorized persons only.
FCC Information
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.(TV, radio, etc.)
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for additional help.
Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following to conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE TO CATV SYSTEM INSTALLER: Call the CATV
system or antenna installer’s attention to Article 820-40 of the NEC. This provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. See installation diagram.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause interference to radio or TV communications. There is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the unit and the television tuner.
- Connect the unit to an AC power outlet on a different electrical circuit.
- Consult your authorized Rotel retailer for assistance.
Important Safety Instructions
WARNING: There are no user serviceable parts inside. Refer all servicing to qualified service personnel.WARNING: To reduce the risk of fire or electric shock, do not expose the unit to moisture or water. Do not expose the unit to dripping or splashing. Do not place objects filled with liquids, such as vases, on the unit. Do not allow foreign objects to get into the enclosure. If the unit is exposed to moisture, or a foreign object gets into the enclosure, immediately disconnect the power cord from the wall. Take the unit to a qualified service person for inspection and necessary repairs. Read all the instructions before connecting or operating the component.Keep this manual so you can refer to these safety instructions. Heed all warnings and safety information in these instructions and on the product itself. Follow all operating instructions.Clean the enclosure only with a dry cloth or a vacuum cleaner. Do not use this unit near water. Do not place the unit on a bed, sofa, rug, or similar surface that could block the ventilation openings. If the unit is placed in a bookcase or cabinet, there must be ventilation of the cabinet to allow proper cooling. Keep the component away from radiators, heat registers, stoves, or any other appliance that produces heat.WARNING: The rear panel power cord connector is the mains power disconnect device. The device must be located in an open area that allows access to the cord connector.The unit must be connected to a power supply only of the type and voltage specified on the rear panel. (USA: 120 V/60Hz, EC: 230V/50Hz) Connect the component to the power outlet only with the supplied power supply cable or an exact equivalent. Do not modify the supplied cable. A polarized plug has two blades, with one wider than the other. A grounding plug has two blades plus a third grounding prong. These are provided for your safety. Do not defeat grounding and/or polarization safety provisions. If the supplied plug does not fit your outlet, pleaseconsult an electrician for replacement of the obsolete outlet. Do not use extension cords. The mains plug is the disconnect of the unit. In order to completely disconnect the unit from the supply mains, remove the main plug from the unit and the AC power outlet. This is the only way to completely remove mains power from the unit. Do not route the power cord where it will be crushed, pinched, bent, exposed to heat, or damaged in any way. Pay particular attention to the power cord at the plug and where the cord exits the back of the unit. The power cord should be unplugged from the wall outlet during a lightning storm or if the unit is to be left unused for a long period of time. Use only accessories specified by the manufacturer. Use only with a cart, stand, rack, bracket or shelf system strong enough to support the unit. Use caution when moving the unit to avoid injury or damage to the unit. Immediately stop using the component and have it inspected and/or serviced by a qualified service agency if:
- The power supply cord or plug has been damaged.
- Objects have fallen or liquid has been spilled into the unit.
- The unit has been exposed to rain.
- The unit shows signs of improper operation.
- The unit has been dropped or damaged in any way.The batteries in the remote control should not be exposed to excessive temperature such as sunshine, fire or other heat sources.
Controls and Connections
Figure 1
RR-T98 Remote Control Пульт ДУ RR-T98
Figure 2
Hook-up Illustration Схема подключения
Important Notes
When making connections be sure to:
- Turn off all the components in the system before hooking up any components, including loudspeakers.
- Turn off all components in the system before changing any of the connections to the system. It is also recommended that you:
- Turn the volume control of the amplifier all the way down before the amplifier is turned on or off.
About Rotel
Our story began over 50 years ago. Over the decades, we have received hundreds of awards for our products and satisfied hundreds of thousands of people who take their entertainment seriously – like you! Rotel was founded by a family whose passionate interest in music led them to manufacture high-fidelity components of uncompromising quality. Throughthe years, that passion has remained undiminished and the family goal of providing exceptional value for audiophiles and music lovers, regardless of their budget, is shared by all Rotel employees. Rotel’s engineers work as a close team, listening to, and fine tuning, each new product until it reaches their exacting musical standards. They are free to choose components from around the world in order to make that product the best they can. You are likely to find capacitors from the United Kingdom and Germany, semiconductors from Japan or the United States,while toroidal power transformers are manufactured in Rotel’s own factory. We all have concerns about our environment. And, as more and more electronics are produced it is especially important for a manufacturer to do all it can to engineer products that have a minimum impact on the environment. At Rotel, we are proud to do our part. We have reduced the lead contentin our products by using special lead-free ROHS solder and components. Our engineers continually strive to improve power supply efficiency without compromise to quality. When in standby mode Rotel products use minimal power to meet global Standby Power Consumption requirements. The Rotel factory is also doing their part to help the environment through constant improvements to product assembly methods for a cleaner and greener manufacturing processes. All of us at Rotel thank you for buying this product. We are sure it will bring you many years of enjoyment.
Getting Started
Thank you for purchasing the Rotel Tuner. When used in a high-quality music or home theater system, your Rotel Tuner will provide years of musical enjoyment.
A Few Precautions
WARNING: To avoid potential damage to your system, turn off ALL the components in the system when connecting or disconnecting components. Do not turn the system components back on until you are sure all the connections are correct and secure. Please read this manual carefully. In addition to basic installation and operating instructions, it provides valuable information on various unit system configurations as well as general information that will help you get the optimum performance from your system. Please contact your authorized Rotel dealer for answers to any questions you might have. In addition, all of us at Rotel welcome your questions and comments. Save the unit shipping carton and all enclosed packing material for future use. Shipping or moving the unit in anything other than the original packing material may result in severe damage to your unit and void the warranty. If included in the box please fill out and send in the owner`s registration card. Also be sure to keep the original sales receipt. It is your best record of the date of purchase, which you will need in the event warranty service is ever required.
Key Features
- Listen to FM and DAB/DAB+ broadcasts.
- 30 Station Presets for memorizing your favorite DAB/DAB+, FM stations.
- RDS (Radio Data System) capability.
- DAB/DAB+ (Digital Audio Broadcast), a digital transmission available throughout Europe and other parts of world
Placement
Place the unit on a solid, level surface away from sunlight, heat, moisture, or vibration.Placement Place the unit on a solid, level surface away from sunlight, heat, moisture, or vibration.
AC Power and ControlAC Power Input q
Your unit is configured at the factory for the proper AC line voltage in the country where you purchased it (USA: 120 volts/60 Hz, Europe: 230 volts/50 Hz). The AC line configuration is noted on a label on the back panel.NOTE: Should you move your unit to another country, it may be possible to reconfigure it for use on a different line voltage. Do not attempt to perform this conversion yourself. Opening the enclosure of the unit exposes you to dangerous voltages. Consult a qualified service person or the Rotel factory service department for information.NOTE: Some products are intended for sale in more than one country and as such are included with more than one AC cord. Please use only the one appropriate for your country/region.
The T11 unit should be plugged directly into a 2-pin polarized wall outlet or into the switched outlet on another component in your audio system. Do not use an extension cord.Be sure the POWER SWITCH 1 on the front panel of the unit is turned off (in the “out” position). Then, connect the supplied power cord to the Power Connector q on the rear of the unit and the AC power outlet. If you are going to be away from home for an extended period of time such as a month-long vacation, it is a sensible precaution to unplug the unit (aswell as other audio and video components) while you are away.
Power Switch 1A and Power Indicator 2
The power switch is located on the left side of the front panel. To turn the unit ON, push the switch in. The indicator light above the switch will light, indicating that the unit isturned on. To turn the unit off, push the button again and return it to the “out” position.
Connection Overview
Before continuing further to other sections in the manual, please make sure all the cable connections are made properly. Refer to figure 3.
DAB/FM Broadcasting 0
Please use the supplied indoor antenna to connect the DAB and FM connector on the rear panel. Experiment with different positions to maximize reception.
RS232 Connector –
The unit can be controlled via RS232 for integration with automation systems. The RS232 input accepts a standard straight DB-9 Male-to-Female cable. For additional information on the connections, software, and operating codes for computer control of the unit, contact your authorized Rotel dealer.
OUTPUT =
The unit outputs a stereo analog signal. Use the supplied audio cable to connect it with input jacks of your pre-amplifier or processor. Be careful and make sure that connections correspond to each other. Right channel output must be connected to right channel of pre- amplifier’s or processor’s right channel and vice versa.
FM RADIO
Before listening to FM radio, make sure that the antenna has been properlyconnected.FM Radio Station Playing
- Select FM Button from the source buttons 5K. The display will show
- Turn the knob 7 on the front panel or use the up/down arrow buttons on the remote control to change the frequency of radio station. Turning the knob on the front panel or using the up/down arrow buttons on the remote control one step at a time changes the frequency one step.
- To auto scan for an FM station, you can choose any of the steps below:• Press and hold the up/down arrow buttons on the remote control.• Press the fast-forward/back-ward F buttons on the remote control
Storing a radio station in a preset
While a radio station is playing, push the memory button 8E, then press the number of preset assigned from numeric keypad 3D, the displaywill show preset saved. Up to 30 preset FM radio stations may be stored.
Playing a preset radio station
When a radio station is playing, you can switch to a preset station in one of the following ways.
- From the numeric keypad 3D, press preset number of the desired station.
- Press the PRESET +/- F buttons on the remote control to view preset numbers and corresponding station. Press the up/down B arrow buttons or the PRESET +/- F buttons on the remote control or turn the knob 7 on the front panel to select the desired station, then press the ENT B button on the remote control to select. Press the FM 5K button againto exit the preset menu and go back to playing status.
Press the FM 5K button and toggle to the FM settings Menu. There are 3 sub-menus under FM setting.
- Scan Settings: Select between STRONG STATIONS ONLY or ALL STATIONS
- Audio Settings: Allow Stereo or Forced Mono.
- FM Preset: Displays all 30 of the FM preset stations and allows tuning to the selected preset by pressing the ENT B button on the remote control.To make changes in the FM settings menu, turn the knob 7 on the front panel or use the up/down B arrow buttons on the remote control. To makea change press the ENT B button on the remote control.
RDS Broadcast Reception
This Rotel unit is equipped with RDS (Radio Data Systems) reception capabilities. The RDS broadcast system provides additional functionality to FM radio reception by transmitting encoded information along with the radio signal. This signal is decoded by an RDS receiver and can provide a range of informational features including:
- A display of the station’s identifying name (e.g. BBC1).
- A display of the station’s program content (e.g. ROCK or NEWS).
- Traffic information broadcasts.
- A scrolling text display for announcements or information.
- Current time and date.RDS broadcasting has been widely available in many European markets for years. There are a large number of RDS stations and most users will befamiliar with the features and operation.
NOTE: The RDS features are entirely dependent on the broadcaster sending properly encoded signals. Thus, they will only be available in markets where RDS is currently implemented and where stations are broadcasting these data signals
The RDS button on the remote control can step through the various displays.Press the RDS button on the remote control to step through the followingdisplays.
- Radio Text.
- Name of station.
- PTY, or the type of content.
- Today’s date and current time.
The MONO button on the remote control changes the FM mode from stereo reception to mono reception. In stereo mode, a stereo signal will be heard if the station is broadcasting a stereo signal and there is sufficient signal strength.
NOTE: Switching to mono mode can be a useful way to improve the reception of weak or distant FM signals. Less signal strength is required for clean mono reception than for stereo reception.
DAB RADIO
Make sure that your local area can receive Digital Audio Broadcast (DAB) broadcasting signal.Press the DAB 6 button on the front of the panel, or remote K. DAB channels are categorized into ensembles, which are also known as multiplexes. Each multiplex provides a number of stations and each service contains a primary service that can contain secondary services. DAB technology allows broadcasters to transmit additional data along with the audio, which can include other audio channels, text and even images and computer data in the future.
DAB Radio Station Playing
- Select DAB 6 Button from the front panel and the unit will scan for available stations. After scanning you will see the following menu.
- Press the ENT B button on the remote control to select the station and start playing the station.
Storing a DAB station in a preset
While a DAB station is playing, push the memory button 8E, then press the number of preset assigned from numeric keypad 3D. Up to 30 presetDAB radio stations may be stored.
Playing a preset DAB station
When a DAB station is playing, you can switch to a preset station in one of the following ways.
- From the numeric keypad 3D, press the preset number of the desired station.
- Press the PRESET +/- F buttons on the remote to view preset numbers and corresponding station. Press the up/down B arrow buttons or the PRESET +/- F buttons on the remote control or turn the knob 7 on the front panel to choose the desired station, then press the ENT B button on the remote control.
Press the DAB 6on the front panel or remote K to toggle to the DAB settings Menu. Turn the knob on the front panel or use the up/down arrowbuttons on the remote control to go through each sub-menu.
- Station List: Shows station list.
- Local Scan: Start a limited scan of available stations by pressing the ENT B button on the remote control. (Not available in all markets).
- Full Scan: Start a full range scan of available stations by pressing the ENT B button on the remote control.
- Manual Tune: Press the ENT B button on the remote control and select stations manually by turning the knob on the front panel or using the up/ down B arrow buttons on the remote control.
- DRC, Dynamic Range Control: Select between “High”, “Low” and “Off”. Press the ENT B button on the remote control and turn the knob on the front panel or use the up/down B arrow buttons on the remote control to change.
- Station Order: Display station order as either “Alphanumeric“, “Ensemble” or “Valid”.
- Prune Station: Select between “Yes” or “No”. The Prune setting allows you to remove stations that are not active or can not be received.
NOTE: Prune will remove unavailable stations from both the Station List and the DAB Preset List.
- DAB Preset: Displays all 30 of the DAB/DAB+ preset stations and allows tuning to the selected preset by pressing the ENT B button on the remote control.
SETUPTo enter the setup menu, press the MENU H button on the remote control and you will see the following display:
- Dimmer: Controls the brightness of the front panel display, it can be dimmed with seven steps. Press the left / right arrow buttons on the remote control to change the display brightness.
NOTE: This setting is stored permanently even after the unit is powered off.To temporarily change the display brightness, press the DIM C button on the remote control.
- Version: Shows the software version loaded in the unit.
- Factory Default: Sets the unit into the original state as when it left the factory. Presets will be lost.
- Exit: Exits the setup menu.
Troubleshooting
Most difficulties in audio systems are the result of incorrect connections, or improper control settings. If you encounter problems, isolate the area of the difficulty, check the control settings, determine the cause of the fault and make the necessary changes. If you are unable to get sound, refer to the suggestions for the following conditions:
Power Indicator Is Not Illuminated
The power Indicator should be illuminated whenever the unit is plugged into the wall power outlet and the power button is pushed in. If it does not light, test the power outlet with another electrical device, such as a lamp. Be sure the power outlet being used is not controlled by a switch that has been turned off.
No Sound
Check the cables between the output and the pre-amplifier inputs, be sure they are connected properly. Refer to Fig. 3.
Cannot Tune to DAB/DAB+ Preset Station
Some stations may become unavailable and will be displayed in the Station List with a “?” character in front of the station name. These stations are no longer broadcasting or received by the T11 unit. Presets that are set to these stations will not function and if selected the T11 unit will display the DAB menu. To remove stations no longer transmitting use the PRUNE function in the DAB Menu. This will remove these stations from the Station List and from the Preset list.
Specifications
FM Tuner
Usable Sensitivity 22.2 dBf50dB Quieting Sensitivity 27.2 dBf (mono) Signal to Noise Ratio (at 65 dBf)MONO 63 dBfSTEREO 60 dBf
Harmonic Distortion (at 65 dBf)
MONO 0.2%STEREO 0.3%Frequency Response 10Hz – 15kHz, ± 3dBStereo Separation 40dB/ 37dB
General
Power Consumption 10 wattsStandby Power Consumption ＜ 0.5 wattsBTU (at 5 watts) 17 BTU/hPower Requirements (AC)USA: 120V, 60HzEurope: 230V, 50HzDimensions (W x H x D) 430 x 73 x 330 mm (17 x 2 7/8 x 13 in)Front panel height 60 mmWeight (net) 4.3 kg (9.48 lbs)
All specifications are accurate at the time of printing. Rotel reserves the right to make improvements without notice Rotel and the Rotel Hifi logo are registered trademarks of The Rotel Co.,Ltd. Tokyo, Japan.
Read More About This Manual & Download PDF:
[xyz-ips snippet=”download-snippet”]