ROVIN Portable Multipurpose Cabinet Camping Light User Manual

ROVIN Portable Multipurpose Cabinet Camping Light User Manual

Standard Configuration

Lamp ×1

USB transfer to DC3.5 USB cable ×1Three-in-one Baseholder ×1（Screw+3M tape）×1

Charging instructions

Charger with output voltage 5V only Do not use charger with output voltage＞5V or current ＞ 2A

USB length: 100cm

laptop USB interfacepower adaptermobile power

Parameter

Bead quantity 20pcs 3000K warm white, 20pcs 6500K cold white
CCT stepless dimming( switch among 3000K-4000K-6000K)
Power 2.5W
Warranty 2 years
luminous flux 200LM
Battery Type 3.7V 2000mAh Lithium Battery
Charging Tme 2 hours get 90% power 3 hours get 100%
Run Time 4-10(high-light level-50% level)
Charge indicator under charging turn to red color, finished charging turn to green color
Interface spec DC3.5V
Waterproof grade IP20
Materia Iron+ABS plug

Notices:

  1. Do not take apart and change interior parts by yourself
  2. Do not look straight under strong light state in case of eye damage
  3. Do not put lamp under high temperature and moist environment
  4. Do not spray any liquid to lamp and put it together with flammable material
  5. Do not charge for too long, cut off power when you leave.

Operating Guide

Short touch– on/CCT change/offLong press–stepless dimming(2-100%) Switch Position: one end with switch sign on the plastic plug

Short touch: First touch: 40pcs beads light up with 4000K ( natural white) Second touch: 20pcs beads light up with 6500K(cold white)Third touch: 20pcs beads light up with 3000K ( warm white) Fourth touch: goes into SOS flashing mode Fifth touch: back to ready mode until next touch for the next cycle Long press: under lighted state, take a long press will achieve stepless dimming. If you take a short touch, the brightness still keep the same level of last one

Notices:

  1. For wall mounted, try to put baseholder in the middle of the lamp
  2. For ceiling mounted, try to put baseholder close to battery part as it’s heavier than the other side so as to keep gravity balance
  3. Avoid violent shaking in case of falling caused by gravity imbalance

Installation

MAGNETPlease ensure adsorbed iron material have enough density, otherwise, the lamp might fall caused by short weight; If the adsorption surface is curved, the lamp might fall as the incomplete absorb surface result in weakness suction.B.3M double-side tape

Double faced+adhesive tap

Adjustable light direction Please ensure pasted surface keep smooth, dry, free of oil and dirt in case of falling. Stick one side to base holder and press hard for 2 minutes, tear off the other side and paste it where you want and give another 2 minutes hard press.

C. Screw

Please prepare your own cross screwdriver and tighten it up in the right position.

safety tips

  1. Do not charge with output voltage 5V, otherwise, the main control IC might be destroyed, which will lead to circuit board protection functions fails and damage battery.
  2. Do not charge with current 2A.
  3. If charge with light on state, ensure keep bightness level 90% to avoid full load operation effect product function, and try not charge 2 hours with light on state.
  4. Do not charge for long time, please cut off power if charged.
  5. Any interior parts are not allowed to be taken apart, fixed and replaced; do not put lamp under high temperature and moist environment and put it together with flammable material

Distributed by: TechBrands by Electus Distribution Pty. Ltd. 320 Victoria Rd, Rydalmere NSW 2116 Australia Ph: 1300 738 555 Int’l: +61 2 8832 3200 Fax: 1300 738 500 www.techbrands.com Made in China

References

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

,