Seychelles Set-ChairAssembly InstructionsProduct size:W63*D63*H79.5 cm
This product is for Domestic Use only!IMPORTANT, RETAIN FOR FUTURE REFERENCE READ CAREFULLY
Before you start
This product doesn’t need any assembly work.
Warnings
IMPORTANT, RETAIN FOR FUTURE REFERENCE READ CAREFULLY
See enclosed instructions for safety and care information. Failure to follow the warnings could result in serious injury. Handle heavy parts with care.This product is intended for Domestic Use only.This product should only be used on firm, level ground. Ensure the product is always placed on level ground.Furniture can be dangerous if used incorrectly or maintained poorly. Keep your furniture in a good condition at all times. No liability will be accepted for damage or injury caused by failure to follow the the care and maintenance guidelines.
PLEASE NOTE -All cushions should be stored indoors after use. The cushions are not waterproof. To clean the chairs or sofa, a pressure washer or jet wash on a wide spray can be used at a minimum distance of lm from the product. Do not aim this directl at the joints of the furniture. Alternatively it can simply be wiped down by hand with a damp sponge and a weak solution of soap and water.The feet on our all-weather wicker products are made from recycled PE materials. We would however still recommend lifting the products to move the items instead of dragging them which may cause some damage to either the product or the area in which you choose to use them.
Use Instruction
Ensure the product is always placed on level ground. We recommend that the cushions are stored indoors or under waterproof cover in wet weather.
Never tilt the product during use. Ensure product is always placed firmly on the ground.
Product Size:Dia 121.5*H80 cm
This product is for Domestic Use only!
IMPORTANT, RETAIN FOR FUTURE REFERENCE READ CAREFULLY
See enclosed instructions far assembly, safety and care information. Failure to follow the warnings could result in serious injury. Handle heavy parts with care, Ensure that this product is fully assembled as illustrated before use. his product should only be used on firm, level ground. Keep small parts out of reach of children. Co not stand or climb onto this product. This product is intended for domestic use only.Furniture can be dangerous if incorrectly used. No liability will be accepted for damage or injury caused by incorrect use of this product.
Do not use scourers, abrasives, washing powders, chemical cleaners or any other substances containing abrasives since these substances can damage the product, including the glass panel.Do not place very hot or very cold items on the glass surface unless adequately thick table-mats are used to prevent such items from coming into contact with the glass.Do not use the glass as a chopping surface. Do not strike the glass with hard or pointed items. Do not use power tools to construct this product. Do not use this product if parts are missing, damaged or worn. Do not sit or lean on this product. Do not stand or climb onto the product and do not use A as a ladder, as this could lead to it unbalancing and overturning. Never drag furniture when moving it, always lift it.
Number of people required for assemblyTwo people
Tips:Do NOT fully tighten bolts before all components are connected. Only fully tighten once you are satisfied with the alignment of all components. Do not over-tighten the bolts.
Components, fixtures & fittings (not actual size)
Parts List
Step by step assembly instructions
All Bolt Head Caps should not be attached before finally tightening all Bolts with Spanner.
Step One
Open the packaging, leave the glass on the carton until the rest of the table is fully assembled.1 With the help of another person, place Table Top Frame (A) upside down on a flat, non-abrasive surface to avoid scratching the table surface or rim.
Step Two
Do NOT assemble the Legs (B) to the Table Top Frame (A) while it is still resting on the Glass Top (D). Loosely attach the Table Legs (B) to the Table Top Frame (A) using Bolt Head Caps (F2), Bolts (W20), and Flat Washers (F3).
Step Three
Loosely attach the Connecting Cross (C) between the Table Legs (B) using Bolt Head Caps (F2), Bolts (W20), and Flat Washers (F3). Only tighten the bolts when all bolts and washers are in place. Once you are satisfied with the alignment of the components carefully tighten all bolts using Spanner (S1). Do not over-tighten. Cover each bolt with Bolt Head Cap (F2).
Step Four
With the help of another person, carefully turn the table in the upright position. Level the table by adjustable feet screw. Carefully place the Glass Top (0) on the Table Top Frame (A) and make sure it is fully rested inside the frame. Your table is now ready for use.
www.royalcraft.co.ukProduced in China for A.Mir & Co. Ltd.©A.Mir & Co.Ltd.
[xyz-ips snippet=”download-snippet”]