saferhome Wireless Alarm System User Manual

Wireless Alarm SystemUser Manual

Note:

1. The alarm system has been programmed already, please operate the system according to part 2 of the manual;2. If you want to add additional HTZSAFE sensors to the system, please operate the system according to part 3 of the manual or contact us directly. After-sale Service:E-mail: [email protected]

System Components And Usage

Plug-in Alarm Receiver

Power Plug: plug the receiver into a socketVolume: 4 volume levels adjustableMelody: 35 classic melodies optionalIndicator Light: flash for several seconds when the sensor be activated

Speaker: sound for several seconds when the sensor be activated

Solar Wireless Motion Sensor

Sensor Eye: detect the objectsSolar Panel: charge the built-in battery of the sensorDrain Hole: used to drain out the rainwater (please note the drain hole must be at the bottom when you install the sensor)Charge Jack: used to connect the additional solar panel or DC 5V power adapterON/OFF: turn on/off the sensor

ATTENTION PLEASE

The KIT includes a charging cable that is used to charge the solar wireless motion sensor before use or if long-term continuously rainy days caused low battery. Please charge the sensor for 4 hours as below:

Operation Instructions

Step 1

Plug the receiver into an outletThe indicator light of the receiver will flash for 15 seconds means working properly

Step 2 Turn on the Wireless Motion Sensor: Press the ON/OFF button 4 times(OprNes/sO4FFtimes) (bleep prompt means work normally)

Step 3Activate The Wireless Motion Sensor (wait about 30 seconds after you turned on the sensor)1st method: press the ON/OFF button twice(the light of the ON/OFF button will flash once means the motion sensor was activated and sent the alarm signal)

2nd method: Ensure the sensor is turned away from you. and walkthrough in front of the sensor to activate(the light of the ON/OFF button will flash once means the motion sensor was activated and sent the alarm signal;and then the motion sensor will back to work mode automatically after about 10 seconds if not detecting any movements)

Step 4Press “Melody” once to choose the melody for this sensor, total 35 melodies optional.Step 5Same steps for the other sensorsStep 6Installations

Wireless Motion Sensor

Installation Notes:

1. Please fix the motion sensor tightly to ensure the position and the direction will not be moved easily by wind.
2. Please point the sensor towards an open field(not towards the trees or bushes)
3. please adjust the sensor a little down(not upward)

Other Settings

(1) How to add additional sensors to the receiver(up to 32 sensors can be added to 1 receiver)Step 1Plug the receiver into an outletStep 2Press and hold the “Volume” button for 5 seconds and release the button when you heard a beep prompt and the indicator light flashing;

Step 3Activate the sensor.Note: please make the sensor close to the alarm receiver(the indicator light flashing 3 times means the sensor was activated properly)(a ring tone prompt and the indicator light flashing quickly means the sensor has been added to the wireless alarm receiver successfully)

Step 4Activate the sensor again to confirm the sensor has been added to the receiver already.

Step 5Press the “Melody” button to choose the melody for this sensor. total 35 melodies optional.

(2) How to delete the sensors of the receiverStep 1Plug the receiver into a outletStep 2Press and hold both the “Volume” button and “Melody” button for 10 seconds and release the buttons when you heard a long beep prompt;Note: all the sensors will be deleted by this operation.

(3) How to adjust the alarm volumeStep 1Plug the receiver into an outletStep 2Press the “Volume” once to adjust the volume of the receiver. (total 4 volume levels adjustable)(4) How to change the melody for the sensors (total 35 melodies optional, match different melody with different sensor)Step 1Plug the receiver into an outletStep 2Activate the sensor first, and then press the “Melody” button to choose the melody for this sensor Same steps for other sensors which have been added to the receiver already.(5) How to adjust the sensitivity of the sensorThe sensor has 3 sensitivities adjustable (High, Middle, Low)Step 1turn off the sensor by press the ON/OFF button 3 timesStep 2If select Low sensitivity—turn on the sensor by pressing the ON/OFF button 3 timesIf select Middle sensitivity—turn on the sensor by pressing the ON/OFF button 4 timesIf select High sensitivity—turn on the sensor by pressing the ON/OFF button 5 times

Technical Parameters

Plug-in Alarm Receiver

Technical parameters

Wireless Motion Sensor

Technical parameters

After-sale Service:E-mail:[email protected]