SATO Thermal UHF RFID Printer User Guide

SATO Thermal UHF RFID Printer User Guide

 

SATO Thermal UHF RFID Printer

Quick Guide

This is the quick start guide for your first operation. For detail, refer to the operator manual available on your region’swebsite https://www.sato-global.com Illustrations used in this quick guide is CL4NX Plus unless otherwise specified. This equipment is not suitable for use in locations where children are likely to be present.When carrying this equipment, be careful not to drop it. There is a risk of injury.

Accessories

  1. CL4NX Plus/CL6NX Plus
  2. Quick guide
  3. Global Warranty Program leaflet
  4. Documents
  5. Power cord
    • The shape of power plug varies depending on the region.

Parts Identification

  1. (Power) button
  2. Operator panel
  3. Media discharge outlet
  4. USB connector (Type A)
  5. Top cover
  6. Ribbon rewind spindle
  7. Ribbon supply spindle
  8. Media holder guide
  9. Media holder
  10. AC input terminal
  11. USB connector (Type A)
  12. RS-232C connector
  13. IEEE1284 connector
  14. EXT connector
  15. USB connector (Type B)
  16. LAN connector
  17. WLAN antenna(optional)Options
  18. Cutter unit
  19. Dispenser unit
  20. Rotary cutter kit (CL4NX Plus only) Connecting the Power Cord

 

  1. Connect the power cord to the AC input terminal .
  2. Plug the power plug into an AC outlet.

Loading Ribbon (For thermal transfer)

  1. Open the top cover fully to prevent accidental dropping of the cover.
  2. Push the ribbon rewind spindle all the way in.
  3.  Push the head lock lever toward the rear.
  4.  Load and insert the ribbon onto the ribbon supply spindle all the way in while taking note of the wind direction.
  5.  From the ribbon supply spindle , pass the ribbon below the print head . 6 Wind the ribbon counterclockwise to the ribbon rewind spindle and grip sheet .
  6.  Press the print head down until the head lock lever is locked.
  7. Close the top cover.

Loading Media

  1.  Open the top cover fully to prevent accidental dropping of the cover.
  2. Push the head lock lever toward the rear.
  3. Pull the media holder guide and media guide away from the product. Turn the knob counterclockwise to release the media guide.
  4.  Load the media roll firmly onto the media holder
  5. Push the media holder guide lightly against the media roll.
  6.  Pass the media below the media damper and the media sensor guide while pushing the media toward the inside of the product. Make sure that the end of the media extends out the front of the product.
  7.  Push the print head down until the head lock lever is locked.
  8. Push the media guide lightly against the near side of the media and turn the knob to lock the media guide.
  9. Close the top cover.

Powering-On the Product Press the(Power) button until the LED of the operator panel lights in blue.Starting Up the Product (Startup Guide) When you power-on the product for the first time after purchase, the display shows the startup guide. The startup guide is to help you through the initial product settings, such as setting the time and date, and loading the ribbon and media.Follow the displayed instructions. You can close the startup guide and perform configuration later from the menu.

Powering-Off the Product

  1.  Make sure that the product is in Offline mode.
  2. Press and hold the (Power) button for more than two seconds.Basic SpecificationsModel name: CL4NX Plus/CL6NX PlusPrint method: Direct thermal and Thermal transferHead density (Resolution):CL4NX Plus: 203, 305, 609 dpi (8, 12, 24 dots/mm)CL6NX Plus: 203, 305 dpi (8, 12 dots/mm)Dimensions:CL4NX Plus: 271 (W) x 457 (D) x 321 (H) mm
  3. (10.7″ x 18.0″ x 12.6″) (Excludes projection)CL6NX Plus: 338 (W) x 457 (D) x 321 (H) mm(13.3″ x 18.0″ x 12.6″) (Excludes projection)

Weight:CL4NX Plus: 15.1 kg (33.3 lbs) (Excludes media, ribbon and options)CL6NX Plus: 20.3 kg (44.7 lbs) (Excludes media, ribbon and options)

Power requirements:

  1.  Input voltageCL4NX Plus: AC 100 – 240 V, 3.0 A, ±10 %CL6NX Plus: AC 100 – 240 V, 4.5 A, ±10 %
  2. Frequency: 50 – 60 Hz
  3. Power consumptionInput power voltage condition: AC 230 V, 50 HzCL4NX Plus: At peak: 190 VA / 180 W (at 30 % printing ratio)Standby: 40 VA / 20 WCL6NX Plus: At peak: 233 VA / 217 W (at 30 % printing ratio)Standby: 60 VA / 23 W

Environmental conditions (Temperature/Humidity):

  1.  Operating: 0 – 40 ºC (32 – 104 ºF), 30 – 80 % RH (non-condensing)
  2. Storage: -20 – 60 ºC (-4 – 140 ºF), 30 – 90 % RH (non-condensing)

Technical Specification ([B] Bluetooth [W] Wireless LAN [U] RFID UHF *1 [H] RFID HF (CL4NX Plus) [N] NFC)Frequency band: [B] 2402 – 2480 MHz, [W] 2412 – 2472 MHz, 5180 – 5825 MHz, [U] 865 868 MHz, 902 – 928 MHz, [H] 13.56 MHz, [N] 13.56 MHz, Modulation: [B] GFSK, DQPSK, 8DPSK, [W] DSSS, OFDM, [U] PR-ASK, [H] ASK, [N] NFC Type 2 Tag (Passive), Max. output power*2: [B] 10 dBm, [W] 20.5 dBm, [U] 30 dBm, [H] 23 dBm, Antenna Gain*2: [B] +1.4 dBi, [W] +2.5 dBi, [U] -41.97 dBi(SRA), -21.36 dBi(FRONTCOUPLER), [H] -65 dBi

  1. The frequency written above is the specification of the module, and the frequency range is limited by regional regulation of each country where the printers are sold.
  2.  [N] Operating distance of up to 100 mm (depending on various parameters, such as field strength and antenna geometry)

References

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

, , ,