Executive SafesOwner’s Manual
WARNINGSentrySafe recommends that you do not store loaded guns in this unit.This is a California-approved firearm safety device that meets the requirements of Penal Code section 23655 and the regulations issued thereunder.
NOTICEDo NOT store delicate items directly in your safe.
SentrySafe products which offer fire protection have proprietary insulation that has a high moisture content. In addition, the SentrySafe advanced safes close airtight to offer water resistance, which may also cause moisture to accumulate inside your safe. The desiccant packet included in your safe during shipment should be left in your safe. DO NOT DISCARD IT. It is intended to help absorb moisture that may accumulate inside your safe. Please open your unit once every two weeks to avoid moisture accumulation. If you choose to store delicate items such as jewelry with working parts, watches, stamps, or photos in your safe, we recommend putting them in an air-tight container, prior to placing them in the safe for storage.
NOTE: SentrySafe will not be responsible for any damage or loss of items placed in the unit due to moisture.
DO NOT store pearls in this safe.In the event of a fire, potential damage to delicate pearls occurs at temperatures much lower than the 350°F interior performance measure which the UL classification performance standard indicated guarantees. Therefore, DO NOT store pearls in your SentrySafe product.
No computer disks, audio-visual cassettes, or photo negatives.This product is not intended to protect computer floppy or diskettes, cartridges, and tapes, audio or video cassettes, or photo negatives.
Liquids can damage the keypad!
Pen points or other sharp objects can puncture the keypad membrane!
Your safe is only part of your total security protection.SentrySafe recommends that you store your safe in closets, offices, basements, bedrooms, and any other locations that are convenient for you but out of the direct line of sight from prying eyes. The location of the safe does not affect the safe’s ability to protect your valuables inside.If children live or visit in your home, do not leave your SentrySafe Executive Safe open and unattended. Children at play could accidentally be locked inside the safe. Keep your safe closed and locked at all times.
Thank you for your purchase of a SentrySafe Product. SentrySafe is committed to securing, organizing, and protecting your most important documents, valuables, and keepsakes.
•••IMPORTANT•••DO NOT RETURN SAFE TO THE STORE!
If you experience any problems or challenges with your safe, please contact us. Many issues can be resolved quickly without the product being returned.
Registration:www.registermysafe.comReasons to registerBy registering your SentrySafe product you can easily retrieve forgotten codes and combinations. By registering your SentrySafe product you can be sure that in the unfortunate circumstance of a fire you will be guaranteed your replacement safe (provided official paperwork has been completed).
Bolt-down instructions
To provide water resistance this safe must be bolted down. (hardware supplied)Bolt down kit contents:2 Lag screws2 Washers
Tools needed to bolt safe to a surface:DrillWrench9/32″ (7.2 mm) drill bit – for drilling into wood3/8″ (9.5 mm) drill bit – for drilling into masonry
Select a suitable and convenient location for your safe. Set the safe in place and use the holes provided in the bottom or back of the safe to mark the location of the holes to be drilled in the floor.- Move the safe away and drill holes of the appropriate diameter and depth for the type of hardware and the mounting surface being used (2 each – bolts, washers, and masonry anchors).
- Place the safe back over the holes and install the fasteners as required. If a water-resistant unit was purchased, rubberized washers are provided. Assure that the area around the safe hole opening is clean using a damp cloth. Place the rubber side of the washer facing down against the safe floor and install the fastener.
Select a suitable and convenient location for your safe. Set the safe in place and use the holes provided in the bottom or back of the safe to mark the location of the holes to be drilled in the floor.
NOTE: SentrySafe is not responsible for any costs incurred if the unit is to be replaced.
Lock instructions
Standard Electronic Lock
To activate lock:Four alkaline AA batteries, Voltage: 6Vdc, (not included) are required to activate the keypad.NOTE: Do not use rechargeable batteries or any other type of non-alkaline battery. Do not mix old and new batteries. Do not mix alkaline and standard batteries.
To install batteries
- Using two hands, hold the keypad, thumbs down, on its left and right sides. Push up the keypad with your thumbs, and disconnect it from the safe by pulling it towards you.
- Let the disengaged keypad hang by its wires. This will expose the battery holder.
- Install four alkaline AA batteries as illustrated on the back of the battery holder.
- Reconnect the keypad by inserting the keypad’s four posts into the matching holes.
- Push down to snap into place.
Using two hands, hold the keypad, thumbs down, on its left and right sides. Push up the keypad with your thumbs, and disconnect it from the safe by pulling it towards you.
NOTICETest first with the door open!(See the back cover of this manual for your factory code.)
Access codes
There are three possible ways to unlock and access the safe—by entering its preset Factory Code, your own User Code, or a User PIN (Personal Identification Number).You can always open the safe by entering the 5-digit Factory Code. This code cannot be deleted.But if you prefer to use your own code, you can program the safe to open to the 5-digit User Code of your choice. If you wish to give someone else temporary access to the safe, you can program a User PIN that can later be erased.
Programming a user code
There are two ways to program a user code.
Press the Program button. (Prog).
Enter the Factory Code. The green LED remains ON while you enter the 5-digit user code of your choice. After 5 digits are entered the green LED turns OFF.(To enter a new User Code, repeat these steps.)–OR–Press the red button on the inside of the door (hinge side). The lock will “beep” and the green LED will come on.
Enter a 5-digit user code. (To enter a new User Code, repeat these steps.)
Keep your new user code secure For your records, please copy it here:
Programming a user PIN
- Press the Program button.
- Press it a second time.
- Enter your 5-digit User Code. The green LED remains ON.
- Enter the 5-digit User PIN of your choice (any combination except 00000.) After 5 digits are entered, the green LED turns OFF.(To enter a new User PIN, repeat these steps. To erase the User PIN, press Program twice, enter your User Code, and then enter 00000.)If your electronic lock fails or you do not have any codes available, you may use the override key that comes with the unit.
Key override
- Using two hands, hold the keypad, thumbs down, on its left and right sides. Push up the keypad with your thumbs, disconnect and remove the battery holder.
Troubleshooting
2. Insert the skeleton key into the keyhole inside the opening for the battery.
3. Turn the key to the right.
4. Open the door.
Signals
Your electronic-lock safe communicates by means of several audio/visual signals.
| The Problem: | Why It Is Happening: | The Solution: |
| Red (Error) LED + three beeps indicates one of the following | You have pressed the Program key out of sequence. | Verify the code and re-enteror reprogram |
| You have entered an invalid code or user pin. | Verify the code and re-enteror reprogram | |
| You have let 5 seconds or more elapse between key presses. | ||
| Lights after three consecutive invalid codes are input (2-minute delay mode). | ||
| Green LED only | Comes ON after you enter a valid code and remains lit during the 4- the second period in which the safe can be opened. | |
| Comes ON in the Programming mode and remains lit until you have finished entering a 5-digit code. | ||
| Yellow LED only | The yellow light comes ON | Batteries need to be replaced. |
Delay mode
The lock automatically enters a 2-minute Delay mode after an invalid code has been entered three consecutive times. In this mode, the lock cannot be activated and any key entry will generate an ERROR signal.
Customer Servicewww.sentrysafe.comCustomer Service: 1-800-828-1438
Peril Protection
Fire ProtectionVerified by ETL SEMKO to meet manufacturer’s specification for fire resistance 1400°F (760°C) for 30 minutes endurance.
How to obtain a replacement key
To order replacement keys and/or combinations, we must have the correct model and a serial number of your safe. Find your safe’s Serial Number on the small label located on the outside of your safe and on the original owner’s manual. Once you locate this information, please visit www.sentrysafe.com or call customer service at 1-800-828-1438.Customer Service: 1-800-828-1438www.sentrysafe.com®2017Master Lock Company LLCMilwaukee, Wisconsin 53210 U.S.A.www.masterlock.com
References
[xyz-ips snippet=”download-snippet”]